!
! EVN Calibration Information File - To be used with the AIPS ANTAB program
! 
! Experiment : S02L1
! Date(s)    : 
! Waveband   : 
! Stations   : Wb
! Comments   : 
!
! See the file s02l1_tsys.ps on vlbeer for a plot of the Tsys in this
! experiment.
!
! N.B. You should remove from this file any antenna gain curves for antennas
! for which you have no data.
! N.B. Also check that the INDEX lines for each antenna are correct for this
! experiment/data format.
! N.B. If this experiment involves more than one frequency, you must run ANTAB
! once for each frequency. If the INDEX lines are different for each frequency
! then you must commenting out the INDEX lines in this file for the other
! frequencies.
!
! Compiled by Cormac Reynolds (reynolds@jive.nl) Wed
! Version: newantab.pl - 23 Apr 2002
!
! Send any changes or updates to the antenna information or queries about this
! file to the email address given above.
!
! Polarization 
! ------------
!
! If there is only one polarization available this is indicated by having DPFU
! value 0.0 for RCP (0.0 for LCP for S and X Band). The RCP DPFU is specified
! first, followed by a comma, and then the LCP DPFU.
!
! INDEX Line
! ----------
! 
! It is IMPORTANT to ensure the INDEX lines are correct. By default they are
! arranged such that the IF with the lowest frequency LCP is L1, the lowest
! frequency RCP is R1, etc. If you have any doubts about them, please contact
! the email address above for assistance.
!
! Negative TSYS values:
! ----------------------
!
! Overflows have been replaced by -2 in the appropriate column and missing
! measurements by -3. These values will be ignored by the AIPS task ANTAB. The
! user should replace any other numbers that they deem inappropriate (very high
! Tsys values) with appropriate numbers from adjacent scans or IFs. Some
! interpolation may already have been done by the producer of this file; see
! the comment line above for a brief description.
!
! TIMEOFF
! ----------
!
! In the absence of continuous TSYS measurements, the TIMEOFF keyword can be
! used to incorporate TSYS measurements made before/after the scan. Since ANTAB
! requires that the measurement falls within the scan itself TIMEOFF=90 is
! used. This will displace the measurement by 90 seconds. In the case of short
! scans this number should be lowered so that the measurement falls within the
! scan. Try with lower values until ANTAB recognises the value. Alternatively,
! you may set TIMEOFF to 0 and use the option 'OFFSET' in ANTAB instead to
! increase the effective length of the scans. In many cases - especially when
! there are Tsys at both ends of the scan - this is preferable to using
! TIMEOFF.
!
! Global VLBI Experiments Correlated at Socorro
! ---------------------------------------------
!
! Global experiments correlated at Socorro may have the TSYS and GAIN
! information for the Effelsberg antenna (EB) transferred automatically with
! the data in a format suitable for use with the AIPS task APCAL (in the same
! way as the VLBA antennas). If this is the case then the TSYS and GAIN entries
! for EB should be removed from this file before running ANTAB.
!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!                                                                   !
!    PIs should  carefully check TSYS values for obvious errors.    !
!                                                                   !
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!
!
!
! Station Comments:
!
!015 04:29.30:" S02L1     2002 WSTRBORK  W   Wb 
!015 04:29.30:" W  WSTRBORK HADC 4.9500 15.0    10 999.9 -999.9 15.0    10 999.9 -999.9 0.0 Wb      
!015 04:29.30:" Wb WSTRBORK  3828444.78000   445223.49000  5064921.57000          
!015 04:29.30:"       WSTRBORK 1417600  
!015 04:29.30:"  drudg version 011011 compiled under FS 9.5.2 
!015 07:04.70:" tied array problem from 06:22:30 to end
!015 07:05.13:" no useful data in the last 38 minutes
/