Welcome to program SCHED. Version: 10.20 Release of about July 12, 2012 The manual is at http://www.aoc.nrao.edu/software/sched/index.html Unix users should set $SCHED to the base area where SCHED is installed. Most run time messages will be in sched.runlog Some useful commands to give now if running interactively: SCHedule= : Specify input file. PLOT : Invokes uv, xy, rd, and uptime plotting. FREQLIST=lowF,highF : Make frequency list (MHz). Then exit. EXIT : Leave program. / : End of inputs - run program (or EXIT). RDSET: Reading setup 1 sess312.L1024 RDSET: Reading setup file: sess312.L1024 SRREAD: Reading source catalog: Program_input STREAD: Reading station catalog: /home/deane/sched10.2/catalogs/stations.dat STREAD: Reading locations file: /home/deane/sched10.2/catalogs/locations.dat SRREAD: Reading source catalog: /home/deane/sched10.2/catalogs/sources.vlba GETFREQ: Reading frequency file: /home/deane/sched10.2/catalogs/freq.dat INPUT: Found 240 input scans. SHORTN: WARNING - Source names longer than 8 characters used. Mark III correlators and geodetic software will have problems. SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETFCAT: In setup: sess312.L1024 Station JODRELL1 Only 224.98 of 256.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: sess312.L1024 Station WSTRBORK Only 244.98 of 256.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: sess312.L1024 Station MEDICINA Only 160.00 of 256.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: sess312.L1024 Station SHANGHAI Only 244.98 of 256.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: sess312.L1024 Station NOTO Only 215.02 of 256.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: sess312.L1024 Station HART Only 244.98 of 256.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: sess312.L1024 Station ONSALA85 Only 240.00 of 256.00 MHz total bandwidth is within the IFs in the setup file before any FREQ or DOPPLER shifts. SETFCAT: In setup: sess312.L1024 Station EFLSBERG WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band ef1570 1 1 F F T T T T T T ef1570 2 2 F F T T T T T T ef1570 3 1 F F T T T T T T ef1570 4 2 F F T T T T T T ef1570 5 1 F F T T T T T T ef1570 6 2 F F T T T T T T ef1570 7 1 F F T T T T T T ef1570 8 2 F F T T T T T T ef1570 9 1 F F T T T T F T ef1570 10 2 F F T T T T F T ef1570 11 1 F F T T T T F T ef1570 12 2 F F T T T T F T ef1570 13 1 F F T T T T F T ef1570 14 2 F F T T T T F T ef1570 15 1 F F T T T T F T ef1570 16 2 F F T T T T F T ef1590 1 1 F T T T T T T T ef1590 2 2 F T T T T T T T ef1590 3 1 F T T T T T T T ef1590 4 2 F T T T T T T T ef1590 5 1 F T T T T T T T ef1590 6 2 F T T T T T T T ef1590 7 1 F T T T T T T T ef1590 8 2 F T T T T T T T ef1590 9 1 F T T T T T T T ef1590 10 2 F T T T T T T T ef1590 11 1 F T T T T T T T ef1590 12 2 F T T T T T T T ef1590 13 1 F T T T T T T T ef1590 14 2 F T T T T T T T ef1590 15 1 F T T T T T T T ef1590 16 2 F T T T T T T T ef18cm 1 1 F F T T T T T T ef18cm 2 2 F F T T T T T T ef18cm 3 1 F F T T T T T T ef18cm 4 2 F F T T T T T T ef18cm 5 1 F F T T T T T T ef18cm 6 2 F F T T T T T T ef18cm 7 1 F F T T T T T T ef18cm 8 2 F F T T T T T T ef18cm 9 1 F F T T T T T T ef18cm 10 2 F F T T T T T T ef18cm 11 1 F F T T T T T T ef18cm 12 2 F F T T T T T T ef18cm 13 1 F F T T T T T T ef18cm 14 2 F F T T T T T T ef18cm 15 1 F F T T T T T T ef18cm 16 2 F F T T T T T T --------------------------------------- TWOHDSET: Using 64 track mode for wide bandwidth. TWOHDSET: Using 16 Mbps per track record rate. Mark IV format on disk only. SCHOPT: First output scan will be number 1 WRTMSG: Special message from routine AUTODOWN: * Stations using automatic tape allocation or disk recording systems are being removed from scans when the source is below the antenna pointing limits. This behavior can be overridden using DODOWN. SCHOPT: There will be 240 output scans ( 1 - 240) from 298/06:30:00 to 298/18:00:00 CHKSCN: 167 scans had more than half the antennas arrive on-source after the start time. This could be normal if using duration scheduling with small gaps. SUMOPE: Writing summary file ed039.sum PROTECT: No PT or MK, so will not check that preemptable times are present. STALST: WARNING - A station has zero axis offset, which is unlikely. Accurate positions, including axis offsets are needed for correlation. Is your station location information adequate? See the summary file station list to see which stations are suspect. OMSOUT: Writing OMS file ed039.oms VXWRT : Writing V E X file ed039.vex JODRELL1: only 123 out of 126 Tsys measurements are on-source TORUN : only 72 out of 73 Tsys measurements are on-source EFLSBERG: only 72 out of 73 Tsys measurements are on-source SHANGHAI: only 17 out of 18 Tsys measurements are on-source VXSCH: Stations listed above are affected by slewing during Tsys calibration WRTMSG: Special message from routine VXSCH: Note that although you may have left gaps during which the system temperature can be measured at MkIV stations, one or more stations are still slewing at the scan starts. System temperatures measured when the antennas are slewing are unlikely to be useful. The time between useful Tsys measurements is therefore likely to be longer than the recommended 15 minutes at the stations listed above. Note that warnings about Westerbork and Arecibo can be safely ignored. V2DOUT: Writing V2D file ed039.tv2d FLAGS: Writing apriori flagging file ed039.flag Processing JODRELL1 Processing WSTRBORK Processing MEDICINA Processing ONSALA85 Processing TORUN Processing EFLSBERG Processing SVETLOE Processing ZELENCHK Processing BADARY Processing SHANGHAI Processing URUMQI Processing NOTO Processing HART Processing ARECIBO