! FREQUENCY CATALOG for SCHED. ! ! The version is set up for the 512-1024 MHz IF range of the RDBE ! system. The rf ranges are slightly offset from the original ! freq.dat. ! This file gives a selection of possible frequency setups for ! many active VLBI stations. For the VLBA, the selection is ! basicaly complete - nearly all valid setups are included. For ! other stations, many of the frequently used setups are included. ! SCHED can use this file to find the appropriate LO and IF settings ! given the desired observing frequencies. The user should not ! need to know the hardware setups at the various stations. In ! fact, users should avoid making their own frequency setups if ! possible. If the desired frequency is in this file, it won't ! be necessary to bother the station friends for information. And ! this file is kept reasonably up to date so it should be trusted ! more than information in old schedules. ! ! SCHED will also use this file to check against any user generated ! setups. If the user setup does not match one here, warnings will ! be issued as a flag that the user should make doubly sure that ! the setup is ok. ! ! The input parameters are: ! STATION Stations covered by this group. ! PRIOrity Lower values are favored groups. ! RF1 Lower limit of RF frequencies covered by this group. ! RF2 Upper RF limit. ! POL Polarization of this IF. ! LO1 The sum of all LOs other than the BBC. ! IFNAME The name of the IF as used by control software. ! FE The front end name (mainly VLBA). ! SYN The 3 VLBA front end synthesizer settings. ! DUALX Use the wide band X band system on the VLBA. ! CH1RF1 Lower hard RF limit for channel 1. Mainly for 2cm VLBA. ! CH1RF2 Upper hard RF limit for channel 1. These select filter. ! RCP50CM, LCP50CM 50 cm VLBA filter (NARROW or BROAD) ! ! VLA specific items. For the meaning of most, see the SCHED manual. ! CHNSTA Used to show if IF is phased array or single dish. (obsolete) ! VLABAND, VLABW, VLAFEAB, VLAFECD, VLASYNA, VLASYNB, FLUKEA, FLUKEB ! ! ! For each of the VLBA bands, a summary of significant filters and ! LO's is given in the comments. ! Receiver and filter ranges are to nominal 1/2 power points. ! The "maximum range" and "good range" are taken from examination of ! plots of measured data in VLBA Test Memo 51. These are subjective, ! eyeball estimates. Anyone attempting to schedule near the limits ! should look at Memo 51. ! The protected bands in the U.S., that are within VLA or VLBA ! bands, are (from VLA-VLBA Interference Memo No 3): ! 73.00 - 74.60 MHz Primary ! 322.00 - 328.60 Footnote (Primary is fixed and mobile) ! 608.00 - 614.00 Primary ! 1330.00 - 1350.00 Footnote (Primary is Aero navigation) ! 1350.00 - 1400.00 Footnotes for redshifted HI. ! 1400.00 - 1427.00 Primary ! 1610.60 - 1613.80 Secondary for OH. ! 1660.00 - 1670.00 Primary ! 1718.80 - 1722.20 Footnote ! 2290 - 2300 Space Research (DSN) ! 2640.00 - 2655.00 Space Research secondary ! 2655.00 - 2690.00 Secondary (Primary is broadcast satellite!) ! 2690.00 - 2700.00 Primary ! 4825.00 - 4835.00 Footnote ! 4950.00 - 4990.00 Footnote ! 4990.00 - 5000.00 Primary ! 8400 - 8450 Space Research (DSN) ! 14.47 - 14.50 GHz Footnotes ! 15.20 - 15.35 EES, Space Research secondary ! 15.35 - 15.40 Primary ! 21.20 - 21.40 EES, SR primary ! 22.01 - 22.21 Footnote ! 22.21 - 22.50 Primary ! 22.81 - 22.86 Footnote ! 23.07 - 23.12 Footnote ! 23.60 - 24.00 Primary ! 42.50 - 43.50 Primary ! 48.94 - 49.04 Primary ! 86.00 - 92.00 Primary ! ! The full frequency catalog (freq.dat) is maintained in subset files. ! All changes should be made in those files, not in freq.dat itself. ! Any changes made directly to freq.dat will be lost at the next update. ! ! This top information is contained in a file called ! Master_NRAO/freq_top.dat. ! ! ! Before 25mar97 - merge the NRAO and EVN versions Huib-03/97 ! 25mar97 split freq.dat into rcwfreq.dat and huibfreq.dat. ! 28Jul97 Various changes including VLA digital patch panel. ! 08Aug97 Some changes to EVN stations and GB 6cm. ! 09Oct97 Split rcwfreq.dat and huibfreq.dat into freq_VLBA.dat etc. ! .... History not maintained for a long time. ! 2004mar01 Rewrite some of above. Add 86 GHz VLBA frequencies. RCW. ! 2011oct12 Make the RDBE version. RCW. ! ! ---------------------------------------------------------------------- ! VERSION is the date and time when this catalog was ! assembled from the master subcatalogs. VERSION = "2014Apr04-14:16:30" ! ! ===================================================================== ! The following entries in the SCHED frequency catalog are for VLBA ! stations only. ! This version is for use with the RDBE with IF range 512-1024 MHz. ! These stations are maintained in file freq_RDBE_VLBA.dat. ! ===================================================================== ! ! VLBA 50/90 cm 90 cm has fixed upconverting LO at 500 MHz. ! 50 cm has no first LO. ! 50 cm has optional filter 608.2-613.8 MHz. ! 90 cm: Receiver: 312-342 MHz. ! IF filter: 802-852 ! Maximum range: 302-352 ! Good range: 310-346 ! 50 cm: Receiver: 596-626 ! Narrow: Filter: 608.2-613.8 ! Max range: 608.4-613.4 ! Good range: 608.8-613.2 ! Wide: No filter ! Max range: 588-633 ! Good range: 595-628 ! Some sites, especially LA, have RFI that saturates the ! receiver if 50cm wide is used. This also ruins 90cm. ! ! Using extra IF's because the receiver can be called ! by either name. ! ! There is no change here for the RDBE because all ! the frequency ranges are limited by the RF filters. ! Name = v5090n Station = VLBA Priority = 0 rf1 = 302, 302, 608.4, 608.4, 302, 302, 608.4, 608.4 rf2 = 352, 352, 613.4, 613.4, 352, 352, 613.4, 613.4 pol = RCP, LCP, RCP, LCP, RCP, LCP, RCP, LCP ifname = B, D, B, D, B, D, B, D fe ='90cm','90cm','90cm','90cm','50cm','50cm','50cm','50cm' lo1 = -500, -500, 0, 0, -500, -500, 0, 0 rcp50cm = 'narrow' lcp50cm = 'narrow' / Name = v5090w Station = VLBA Priority = 1 rf1 = 302, 302, 588, 588, 302, 302, 588, 588 rf2 = 352, 352, 633, 633, 352, 352, 633, 633 pol = RCP, LCP, RCP, LCP, RCP, LCP, RCP, LCP ifname = B, D, B, D, B, D, B, D fe ='90cm','90cm','90cm','90cm','50cm','50cm','50cm','50cm' lo1 = -500, -500, 0, 0, -500, -500, 0, 0 rcp50cm = 'broad' lcp50cm = 'broad' note = 'Wide 50 cm filter. Beware RFI. Some stations will saturate.' / ! VLBA 20 cm Some sites require special RFI filters. ! Receiver (most) 1265 - 1835 MHz ! Receiver (FD) 1339 - 1756 ! Receiver (KP) 1333 - 1885 ! IF Filter (most) 475 - 1025 ! IF Filter (SC) 665 - 1027 ! The performance at the low end is quite variable - See Memo 51. ! Max range (most): 1180 - 1850 ! Good range (most): 1300 - 1760 ! Max range (FD): 1330 - 1760 ! Good range (FD): 1350 - 1750 ! Max range (KP): 1330 - 1850 ! Good range (KP): 1350 - 1760 ! Max range (SC); 1240 - 1740 ! Good range (SC): 1400 - 1730 (2.4 GHz firstlo only). ! SC might be extended upward with other LOs, but the ! RFI everywhere is so bad up there that it's not ! worth it. ! Note that this band has lots of RFI problems. There is info ! elsewhere on this. See the NRAO home page for VLA and VLBA. ! ! Jan 2013 adding 2.6 GHz LO to give other crossover and PFB ! possibilities. Name = v20cm_1 Station = VLBA Priority = 1 rf1 = 1180, 1180 ifname = A, C rf2 = 1588, 1588 fe = '20cm', '20cm' pol = RCP, LCP lo1 = 2100, 2100 syn(2) = 2.1 note='FD and KP filtered below 1330. SC filtered above 1440' / Name = v20cm_2 Station = VLBA Priority = 0 rf1 = 1376, 1376 ifname = A, C rf2 = 1850, 1850 fe = '20cm', '20cm' pol = RCP, LCP lo1 = 2400, 2400 syn(2) = 2.4 note='FD filtered above 1760. SC filtered above 1740.' / Name = v20cm_2 Station = VLBA Priority = 0 rf1 = 1576, 1576 ifname = A, C rf2 = 1850, 1850 fe = '20cm', '20cm' pol = RCP, LCP lo1 = 2600, 2600 syn(2) = 2.6 note='Beware RFI at high end.' ! Added to give PFB band frequency and DDC crossover flexibility. / ! VLBA 13 cm The nominal band is 2150 - 2350 Mhz, but the receiver ! is much wider than that. For observations well above ! the nominal band, users should consult Memo 51. ! All stations except MK, PT, and FD have a 2200-2400 ! GHz filter because of RFI. Many of the ranges given ! here only apply without that filter. It is possible ! that the additional headroom of the RDBE will allow ! some or all of those filters to be removed in the ! future. ! Receiver: 2000 - 2800 MHz ! LO Filter: 2700 - 3300 ! RFI filters: 2200 - 2400 -1db, 2150 - 2450 -60db ! All but MK, PT, FD. ! Maximum range: 1920 - 2840 without filters. ! Good range: 2000 - 2440 without filters. ! Another OK range: 2490 - 2650 without filters. ! Note that Tcals are poor outside of nominal range so be ! careful with calibration. ! ! Some of the most serious RFI in this band that affects all ! North American stations is from: ! Sirius Satellite Radio 2320.0 to 2332.5 MHz ! XM Satellite Radio 2332.5 to 2345.0 MHz ! Note that the frequency ranges do not take into ! account the S band RFI filters (2200-2400 GHz). Name = v13cm_1 Station = VLBA Priority = 0 rf1 = 1920, 1920 ifname = A, C rf2 = 2388, 2388 fe = '13cm', '13cm' pol = RCP, LCP lo1 = 2900, 2900 syn(2) = 2.9 note='Most only 2200-2400' / Name = v13cm_2 Station = VLBA Priority = 0 rf1 = 2076, 2076 ifname = A, C rf2 = 2588, 2588 fe = '13cm', '13cm' pol = RCP, LCP lo1 = 3100, 3100 syn(2) = 3.1 note='Most only 2200-2400' / ! The LO is a bit high for the IF filter. Name = v13cm_3 Station = VLBA Priority = 1 rf1 = 2376, 2376 ifname = A, C rf2 = 2840, 2840 fe = '13cm', '13cm' pol = RCP, LCP lo1 = 3400, 3400 syn(2) = 3.4 note='Most only 2200-2400' / ! Old VLBA 6 cm This one is fairly simple. ! Receiver: 4500 - 5200 MHz ! LO Filter: 3450 - 4750 ! Maximum range: 4440 - 5240 ! Good range: 4480 - 5200 ! !Name = v6cm_1 Station = VLBA Priority = 0 ! rf1 = 4440, 4440 ifname = A, C ! rf2 = 4924, 4924 fe = '6cm', '6cm' ! pol = RCP, LCP lo1 = 3900, 3900 syn(2) = 3.9 !/ !Name = v6cm_2 Station = VLBA Priority = 0 ! rf1 = 4612, 4612 ifname = A, C ! rf2 = 5124, 5124 fe = '6cm', '6cm' ! pol = RCP, LCP lo1 = 4100, 4100 syn(2) = 4.1 !/ !Name = v6cm_3 Station = VLBA Priority = 1 ! rf1 = 4912, 4912 ifname = A, C ! rf2 = 5240, 5240 fe = '6cm', '6cm' ! pol = RCP, LCP lo1 = 4400, 4400 syn(2) = 4.4 ! / ! VLBA 4-8 GHz receiver. ! With the IF at 512-1024, this one cannot be simple as ! it would be impossible to reach the center of the band ! without aliasing. So there is a choice of 2 filters ! at RF, plus the option to use upper or lower sideband. ! In addition, there can be 4 IF outputs split between ! 2 bands (2 LO's available). ! RF filter 1: 3900.0 - 5900.0 MHz ! RF filter 2: 5600.0 - 7900.0 MHz ! ! Syn(1) is attached to the BD channels. ! Syn(2) is attached to the AC channels. ! ! In some cases, part of a band will be subject to aliased ! signals. The RF ranges reflect the unaffected portions. ! ! The frequency sets below are created by program makefq_c.f ! in the $SCHED/RELATED_CODE/MAKEFREQ area. ! ! The priorities are set to discourage the use of the ! four IF systems when not needed. Name = vc_a Station = VLBA Priority = 1 ! This setup has a potential problem. The first harmonic ! of the LO is at 6800. That can mix with the RF that passes the ! lower filter (20db points 3750 and 6050 MHz) to give signal in the ! IF above 750 MHz. This will land on top of the desired signal ! that comes from RF above 4150. So this setup is primarily ! recommended if the very bottom end of the RF range is needed. ! All that said, no obvious effects showed up in the initial ! wideband tests so it might be ok across the whole band. It ! would depend the unknown strength of the 6800 MHz harmonic. rf1 = 3912., 3912. ifname = A, C rf2 = 4424., 4424. fe = '6cm', '6cm' syn(2) = 3.4 pol = RCP, LCP lo1 = 3400., 3400. note = 'Potential problems above 4150 see note in freq file.' / Name = vc_b Station = VLBA Priority = 0 rf1 = 4112., 4112. ifname = A, C rf2 = 4624., 4624. fe = '6cm', '6cm' syn(2) = 3.6 pol = RCP, LCP lo1 = 3600., 3600. / Name = vc_f Station = VLBA Priority = 2 rf1 = 4376., 4376. ifname = A, C rf2 = 4750., 4750. fe = '6cm', '6cm' syn(2) = 5.4 pol = RCP, LCP lo1 = 5400., 5400. / Name = vc_c Station = VLBA Priority = 0 rf1 = 4412., 4412. ifname = A, C rf2 = 4924., 4924. fe = '6cm', '6cm' syn(2) = 3.9 pol = RCP, LCP lo1 = 3900., 3900. / Name = vc_g Station = VLBA Priority = 1 rf1 = 4576., 4576. ifname = A, C rf2 = 5088., 5088. fe = '6cm', '6cm' syn(2) = 5.6 pol = RCP, LCP lo1 = 5600., 5600. / Name = vc_d Station = VLBA Priority = 0 rf1 = 4612., 4612. ifname = A, C rf2 = 5124., 5124. fe = '6cm', '6cm' syn(2) = 4.1 pol = RCP, LCP lo1 = 4100., 4100. / Name = vc_h Station = VLBA Priority = 0 rf1 = 4876., 4876. ifname = A, C rf2 = 5388., 5388. fe = '6cm', '6cm' syn(2) = 5.9 pol = RCP, LCP lo1 = 5900., 5900. / Name = vc_e Station = VLBA Priority = 2 rf1 = 5050., 5050. ifname = A, C rf2 = 5424., 5424. fe = '6cm', '6cm' syn(2) = 4.4 pol = RCP, LCP lo1 = 4400., 4400. / Name = vc_i Station = VLBA Priority = 0 rf1 = 5076., 5076. ifname = A, C rf2 = 5588., 5588. fe = '6cm', '6cm' syn(2) = 6.1 pol = RCP, LCP lo1 = 6100., 6100. / Name = vc_j Station = VLBA Priority = 0 rf1 = 5376., 5376. ifname = A, C rf2 = 5888., 5888. fe = '6cm', '6cm' syn(2) = 6.4 pol = RCP, LCP lo1 = 6400., 6400. / Name = vc_k Station = VLBA Priority = 2 rf1 = 5576., 5576. ifname = A, C rf2 = 5900., 5900. fe = '6cm', '6cm' syn(2) = 6.6 pol = RCP, LCP lo1 = 6600., 6600. / Name = vc_l Station = VLBA Priority = 2 rf1 = 5600., 5600. ifname = A, C rf2 = 5924., 5924. fe = '6cm', '6cm' syn(2) = 4.9 pol = RCP, LCP lo1 = 4900., 4900. / Name = vc_m Station = VLBA Priority = 0 rf1 = 5612., 5612. ifname = A, C rf2 = 6124., 6124. fe = '6cm', '6cm' syn(2) = 5.1 pol = RCP, LCP lo1 = 5100., 5100. / Name = vc_n Station = VLBA Priority = 0 rf1 = 5912., 5912. ifname = A, C rf2 = 6424., 6424. fe = '6cm', '6cm' syn(2) = 5.4 pol = RCP, LCP lo1 = 5400., 5400. / Name = vc_o Station = VLBA Priority = 0 rf1 = 6112., 6112. ifname = A, C rf2 = 6624., 6624. fe = '6cm', '6cm' syn(2) = 5.6 pol = RCP, LCP lo1 = 5600., 5600. / Name = vc_r Station = VLBA Priority = 2 rf1 = 6376., 6376. ifname = A, C rf2 = 6700., 6700. fe = '6cm', '6cm' syn(2) = 7.4 pol = RCP, LCP lo1 = 7400., 7400. / Name = vc_p Station = VLBA Priority = 0 rf1 = 6412., 6412. ifname = A, C rf2 = 6924., 6924. fe = '6cm', '6cm' syn(2) = 5.9 pol = RCP, LCP lo1 = 5900., 5900. / Name = vc_s Station = VLBA Priority = 0 rf1 = 6576., 6576. ifname = A, C rf2 = 7088., 7088. fe = '6cm', '6cm' syn(2) = 7.6 pol = RCP, LCP lo1 = 7600., 7600. / Name = vc_q Station = VLBA Priority = 2 rf1 = 6800., 6800. ifname = A, C rf2 = 7124., 7124. fe = '6cm', '6cm' syn(2) = 6.1 pol = RCP, LCP lo1 = 6100., 6100. / Name = vc_t Station = VLBA Priority = 0 rf1 = 6876., 6876. ifname = A, C rf2 = 7388., 7388. fe = '6cm', '6cm' syn(2) = 7.9 pol = RCP, LCP lo1 = 7900., 7900. / Name = vc_u Station = VLBA Priority = 0 rf1 = 7076., 7076. ifname = A, C rf2 = 7588., 7588. fe = '6cm', '6cm' syn(2) = 8.1 pol = RCP, LCP lo1 = 8100., 8100. / Name = vc_v Station = VLBA Priority = 0 rf1 = 7376., 7376. ifname = A, C rf2 = 7888., 7888. fe = '6cm', '6cm' syn(2) = 8.4 pol = RCP, LCP lo1 = 8400., 8400. / Name = vc_w Station = VLBA Priority = 1 rf1 = 7576., 7576. ifname = A, C rf2 = 7900., 7900. fe = '6cm', '6cm' syn(2) = 8.6 pol = RCP, LCP lo1 = 8600., 8600. / Name = vc_ab Station = VLBA Priority = 2 rf1 = 3912., 3912., 4112., 4112. ifname = A, C, B, D rf2 = 4424., 4424., 4624., 4624. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 3.6 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 3600., 3600. / Name = vc_af Station = VLBA Priority = 4 rf1 = 3912., 3912., 4376., 4376. ifname = A, C, B, D rf2 = 4424., 4424., 4750., 4750. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 5.4 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 5400., 5400. / Name = vc_ac Station = VLBA Priority = 2 rf1 = 3912., 3912., 4412., 4412. ifname = A, C, B, D rf2 = 4424., 4424., 4924., 4924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 3.9 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 3900., 3900. / Name = vc_ag Station = VLBA Priority = 3 rf1 = 3912., 3912., 4576., 4576. ifname = A, C, B, D rf2 = 4424., 4424., 5088., 5088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 5600., 5600. / Name = vc_ad Station = VLBA Priority = 2 rf1 = 3912., 3912., 4612., 4612. ifname = A, C, B, D rf2 = 4424., 4424., 5124., 5124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 4.1 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 4100., 4100. / Name = vc_ah Station = VLBA Priority = 2 rf1 = 3912., 3912., 4876., 4876. ifname = A, C, B, D rf2 = 4424., 4424., 5388., 5388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 5900., 5900. / Name = vc_ae Station = VLBA Priority = 4 rf1 = 3912., 3912., 5050., 5050. ifname = A, C, B, D rf2 = 4424., 4424., 5424., 5424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 4.4 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 4400., 4400. / Name = vc_ai Station = VLBA Priority = 2 rf1 = 3912., 3912., 5076., 5076. ifname = A, C, B, D rf2 = 4424., 4424., 5588., 5588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 6100., 6100. / Name = vc_aj Station = VLBA Priority = 2 rf1 = 3912., 3912., 5376., 5376. ifname = A, C, B, D rf2 = 4424., 4424., 5888., 5888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 6.4 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 6400., 6400. / Name = vc_ak Station = VLBA Priority = 4 rf1 = 3912., 3912., 5576., 5576. ifname = A, C, B, D rf2 = 4424., 4424., 5900., 5900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 6.6 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 6600., 6600. / Name = vc_al Station = VLBA Priority = 4 rf1 = 3912., 3912., 5600., 5600. ifname = A, C, B, D rf2 = 4424., 4424., 5924., 5924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 4.9 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 4900., 4900. / Name = vc_am Station = VLBA Priority = 2 rf1 = 3912., 3912., 5612., 5612. ifname = A, C, B, D rf2 = 4424., 4424., 6124., 6124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 5.1 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 5100., 5100. / Name = vc_an Station = VLBA Priority = 2 rf1 = 3912., 3912., 5912., 5912. ifname = A, C, B, D rf2 = 4424., 4424., 6424., 6424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 5.4 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 5400., 5400. / Name = vc_ao Station = VLBA Priority = 2 rf1 = 3912., 3912., 6112., 6112. ifname = A, C, B, D rf2 = 4424., 4424., 6624., 6624. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 5600., 5600. / Name = vc_ar Station = VLBA Priority = 4 rf1 = 3912., 3912., 6376., 6376. ifname = A, C, B, D rf2 = 4424., 4424., 6700., 6700. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 7.4 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 7400., 7400. / Name = vc_ap Station = VLBA Priority = 2 rf1 = 3912., 3912., 6412., 6412. ifname = A, C, B, D rf2 = 4424., 4424., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 5900., 5900. / Name = vc_as Station = VLBA Priority = 2 rf1 = 3912., 3912., 6576., 6576. ifname = A, C, B, D rf2 = 4424., 4424., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 7600., 7600. / Name = vc_aq Station = VLBA Priority = 4 rf1 = 3912., 3912., 6800., 6800. ifname = A, C, B, D rf2 = 4424., 4424., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 6100., 6100. / Name = vc_at Station = VLBA Priority = 2 rf1 = 3912., 3912., 6876., 6876. ifname = A, C, B, D rf2 = 4424., 4424., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 7900., 7900. / Name = vc_au Station = VLBA Priority = 2 rf1 = 3912., 3912., 7076., 7076. ifname = A, C, B, D rf2 = 4424., 4424., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 8100., 8100. / Name = vc_av Station = VLBA Priority = 2 rf1 = 3912., 3912., 7376., 7376. ifname = A, C, B, D rf2 = 4424., 4424., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 8400., 8400. / Name = vc_aw Station = VLBA Priority = 3 rf1 = 3912., 3912., 7576., 7576. ifname = A, C, B, D rf2 = 4424., 4424., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.4 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 3400., 3400., 8600., 8600. / Name = vc_bf Station = VLBA Priority = 3 rf1 = 4112., 4112., 4376., 4376. ifname = A, C, B, D rf2 = 4624., 4624., 4750., 4750. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 5.4 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 5400., 5400. / Name = vc_bc Station = VLBA Priority = 1 rf1 = 4112., 4112., 4412., 4412. ifname = A, C, B, D rf2 = 4624., 4624., 4924., 4924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 3.9 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 3900., 3900. / Name = vc_bg Station = VLBA Priority = 2 rf1 = 4112., 4112., 4576., 4576. ifname = A, C, B, D rf2 = 4624., 4624., 5088., 5088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 5600., 5600. / Name = vc_bd Station = VLBA Priority = 1 rf1 = 4112., 4112., 4612., 4612. ifname = A, C, B, D rf2 = 4624., 4624., 5124., 5124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 4.1 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 4100., 4100. / Name = vc_bh Station = VLBA Priority = 1 rf1 = 4112., 4112., 4876., 4876. ifname = A, C, B, D rf2 = 4624., 4624., 5388., 5388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 5900., 5900. / Name = vc_be Station = VLBA Priority = 3 rf1 = 4112., 4112., 5050., 5050. ifname = A, C, B, D rf2 = 4624., 4624., 5424., 5424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 4.4 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 4400., 4400. / Name = vc_bi Station = VLBA Priority = 1 rf1 = 4112., 4112., 5076., 5076. ifname = A, C, B, D rf2 = 4624., 4624., 5588., 5588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 6100., 6100. / Name = vc_bj Station = VLBA Priority = 1 rf1 = 4112., 4112., 5376., 5376. ifname = A, C, B, D rf2 = 4624., 4624., 5888., 5888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 6.4 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 6400., 6400. / Name = vc_bk Station = VLBA Priority = 3 rf1 = 4112., 4112., 5576., 5576. ifname = A, C, B, D rf2 = 4624., 4624., 5900., 5900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 6.6 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 6600., 6600. / Name = vc_bl Station = VLBA Priority = 3 rf1 = 4112., 4112., 5600., 5600. ifname = A, C, B, D rf2 = 4624., 4624., 5924., 5924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 4.9 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 4900., 4900. / Name = vc_bm Station = VLBA Priority = 1 rf1 = 4112., 4112., 5612., 5612. ifname = A, C, B, D rf2 = 4624., 4624., 6124., 6124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 5.1 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 5100., 5100. / Name = vc_bn Station = VLBA Priority = 1 rf1 = 4112., 4112., 5912., 5912. ifname = A, C, B, D rf2 = 4624., 4624., 6424., 6424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 5.4 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 5400., 5400. / Name = vc_bo Station = VLBA Priority = 1 rf1 = 4112., 4112., 6112., 6112. ifname = A, C, B, D rf2 = 4624., 4624., 6624., 6624. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 5600., 5600. / Name = vc_br Station = VLBA Priority = 3 rf1 = 4112., 4112., 6376., 6376. ifname = A, C, B, D rf2 = 4624., 4624., 6700., 6700. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 7.4 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 7400., 7400. / Name = vc_bp Station = VLBA Priority = 1 rf1 = 4112., 4112., 6412., 6412. ifname = A, C, B, D rf2 = 4624., 4624., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 5900., 5900. / Name = vc_bs Station = VLBA Priority = 1 rf1 = 4112., 4112., 6576., 6576. ifname = A, C, B, D rf2 = 4624., 4624., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 7600., 7600. / Name = vc_bq Station = VLBA Priority = 3 rf1 = 4112., 4112., 6800., 6800. ifname = A, C, B, D rf2 = 4624., 4624., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 6100., 6100. / Name = vc_bt Station = VLBA Priority = 1 rf1 = 4112., 4112., 6876., 6876. ifname = A, C, B, D rf2 = 4624., 4624., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 7900., 7900. / Name = vc_bu Station = VLBA Priority = 1 rf1 = 4112., 4112., 7076., 7076. ifname = A, C, B, D rf2 = 4624., 4624., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 8100., 8100. / Name = vc_bv Station = VLBA Priority = 1 rf1 = 4112., 4112., 7376., 7376. ifname = A, C, B, D rf2 = 4624., 4624., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 8400., 8400. / Name = vc_bw Station = VLBA Priority = 2 rf1 = 4112., 4112., 7576., 7576. ifname = A, C, B, D rf2 = 4624., 4624., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.6 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 3600., 3600., 8600., 8600. / Name = vc_fc Station = VLBA Priority = 3 rf1 = 4376., 4376., 4412., 4412. ifname = A, C, B, D rf2 = 4750., 4750., 4924., 4924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 3.9 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 3900., 3900. / Name = vc_fg Station = VLBA Priority = 4 rf1 = 4376., 4376., 4576., 4576. ifname = A, C, B, D rf2 = 4750., 4750., 5088., 5088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 5600., 5600. / Name = vc_fd Station = VLBA Priority = 3 rf1 = 4376., 4376., 4612., 4612. ifname = A, C, B, D rf2 = 4750., 4750., 5124., 5124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 4.1 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 4100., 4100. / Name = vc_fh Station = VLBA Priority = 3 rf1 = 4376., 4376., 4876., 4876. ifname = A, C, B, D rf2 = 4750., 4750., 5388., 5388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 5900., 5900. / Name = vc_fe Station = VLBA Priority = 5 rf1 = 4376., 4376., 5050., 5050. ifname = A, C, B, D rf2 = 4750., 4750., 5424., 5424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 4.4 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 4400., 4400. / Name = vc_fi Station = VLBA Priority = 3 rf1 = 4376., 4376., 5076., 5076. ifname = A, C, B, D rf2 = 4750., 4750., 5588., 5588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 6100., 6100. / Name = vc_fj Station = VLBA Priority = 3 rf1 = 4376., 4376., 5376., 5376. ifname = A, C, B, D rf2 = 4750., 4750., 5888., 5888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 6.4 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 6400., 6400. / Name = vc_fk Station = VLBA Priority = 5 rf1 = 4376., 4376., 5576., 5576. ifname = A, C, B, D rf2 = 4750., 4750., 5900., 5900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 6.6 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 6600., 6600. / Name = vc_fl Station = VLBA Priority = 5 rf1 = 4376., 4376., 5600., 5600. ifname = A, C, B, D rf2 = 4750., 4750., 5924., 5924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 4.9 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 4900., 4900. / Name = vc_fm Station = VLBA Priority = 3 rf1 = 4376., 4376., 5612., 5612. ifname = A, C, B, D rf2 = 4750., 4750., 6124., 6124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 5.1 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 5100., 5100. / Name = vc_fn Station = VLBA Priority = 3 rf1 = 4376., 4376., 5912., 5912. ifname = A, C, B, D rf2 = 4750., 4750., 6424., 6424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 5.4 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 5400., 5400. / Name = vc_fo Station = VLBA Priority = 3 rf1 = 4376., 4376., 6112., 6112. ifname = A, C, B, D rf2 = 4750., 4750., 6624., 6624. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 5600., 5600. / Name = vc_fr Station = VLBA Priority = 5 rf1 = 4376., 4376., 6376., 6376. ifname = A, C, B, D rf2 = 4750., 4750., 6700., 6700. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 7.4 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 7400., 7400. / Name = vc_fp Station = VLBA Priority = 3 rf1 = 4376., 4376., 6412., 6412. ifname = A, C, B, D rf2 = 4750., 4750., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 5900., 5900. / Name = vc_fs Station = VLBA Priority = 3 rf1 = 4376., 4376., 6576., 6576. ifname = A, C, B, D rf2 = 4750., 4750., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 7600., 7600. / Name = vc_fq Station = VLBA Priority = 5 rf1 = 4376., 4376., 6800., 6800. ifname = A, C, B, D rf2 = 4750., 4750., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 6100., 6100. / Name = vc_ft Station = VLBA Priority = 3 rf1 = 4376., 4376., 6876., 6876. ifname = A, C, B, D rf2 = 4750., 4750., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 7900., 7900. / Name = vc_fu Station = VLBA Priority = 3 rf1 = 4376., 4376., 7076., 7076. ifname = A, C, B, D rf2 = 4750., 4750., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 8100., 8100. / Name = vc_fv Station = VLBA Priority = 3 rf1 = 4376., 4376., 7376., 7376. ifname = A, C, B, D rf2 = 4750., 4750., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 8400., 8400. / Name = vc_fw Station = VLBA Priority = 4 rf1 = 4376., 4376., 7576., 7576. ifname = A, C, B, D rf2 = 4750., 4750., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 8600., 8600. / Name = vc_cg Station = VLBA Priority = 2 rf1 = 4412., 4412., 4576., 4576. ifname = A, C, B, D rf2 = 4924., 4924., 5088., 5088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 5600., 5600. / Name = vc_cd Station = VLBA Priority = 1 rf1 = 4412., 4412., 4612., 4612. ifname = A, C, B, D rf2 = 4924., 4924., 5124., 5124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 4.1 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 4100., 4100. / Name = vc_ch Station = VLBA Priority = 1 rf1 = 4412., 4412., 4876., 4876. ifname = A, C, B, D rf2 = 4924., 4924., 5388., 5388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 5900., 5900. / Name = vc_ce Station = VLBA Priority = 3 rf1 = 4412., 4412., 5050., 5050. ifname = A, C, B, D rf2 = 4924., 4924., 5424., 5424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 4.4 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 4400., 4400. / Name = vc_ci Station = VLBA Priority = 1 rf1 = 4412., 4412., 5076., 5076. ifname = A, C, B, D rf2 = 4924., 4924., 5588., 5588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 6100., 6100. / Name = vc_cj Station = VLBA Priority = 1 rf1 = 4412., 4412., 5376., 5376. ifname = A, C, B, D rf2 = 4924., 4924., 5888., 5888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 6.4 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 6400., 6400. / Name = vc_ck Station = VLBA Priority = 3 rf1 = 4412., 4412., 5576., 5576. ifname = A, C, B, D rf2 = 4924., 4924., 5900., 5900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 6.6 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 6600., 6600. / Name = vc_cl Station = VLBA Priority = 3 rf1 = 4412., 4412., 5600., 5600. ifname = A, C, B, D rf2 = 4924., 4924., 5924., 5924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 4.9 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 4900., 4900. / Name = vc_cm Station = VLBA Priority = 1 rf1 = 4412., 4412., 5612., 5612. ifname = A, C, B, D rf2 = 4924., 4924., 6124., 6124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 5.1 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 5100., 5100. / Name = vc_cn Station = VLBA Priority = 1 rf1 = 4412., 4412., 5912., 5912. ifname = A, C, B, D rf2 = 4924., 4924., 6424., 6424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 5.4 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 5400., 5400. / Name = vc_co Station = VLBA Priority = 1 rf1 = 4412., 4412., 6112., 6112. ifname = A, C, B, D rf2 = 4924., 4924., 6624., 6624. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 5600., 5600. / Name = vc_cr Station = VLBA Priority = 3 rf1 = 4412., 4412., 6376., 6376. ifname = A, C, B, D rf2 = 4924., 4924., 6700., 6700. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 7.4 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 7400., 7400. / Name = vc_cp Station = VLBA Priority = 1 rf1 = 4412., 4412., 6412., 6412. ifname = A, C, B, D rf2 = 4924., 4924., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 5900., 5900. / Name = vc_cs Station = VLBA Priority = 1 rf1 = 4412., 4412., 6576., 6576. ifname = A, C, B, D rf2 = 4924., 4924., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 7600., 7600. / Name = vc_cq Station = VLBA Priority = 3 rf1 = 4412., 4412., 6800., 6800. ifname = A, C, B, D rf2 = 4924., 4924., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 6100., 6100. / Name = vc_ct Station = VLBA Priority = 1 rf1 = 4412., 4412., 6876., 6876. ifname = A, C, B, D rf2 = 4924., 4924., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 7900., 7900. / Name = vc_cu Station = VLBA Priority = 1 rf1 = 4412., 4412., 7076., 7076. ifname = A, C, B, D rf2 = 4924., 4924., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 8100., 8100. / Name = vc_cv Station = VLBA Priority = 1 rf1 = 4412., 4412., 7376., 7376. ifname = A, C, B, D rf2 = 4924., 4924., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 8400., 8400. / Name = vc_cw Station = VLBA Priority = 2 rf1 = 4412., 4412., 7576., 7576. ifname = A, C, B, D rf2 = 4924., 4924., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 3.9 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 3900., 3900., 8600., 8600. / Name = vc_gd Station = VLBA Priority = 2 rf1 = 4576., 4576., 4612., 4612. ifname = A, C, B, D rf2 = 5088., 5088., 5124., 5124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 4.1 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 4100., 4100. / Name = vc_gh Station = VLBA Priority = 2 rf1 = 4576., 4576., 4876., 4876. ifname = A, C, B, D rf2 = 5088., 5088., 5388., 5388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 5900., 5900. / Name = vc_ge Station = VLBA Priority = 4 rf1 = 4576., 4576., 5050., 5050. ifname = A, C, B, D rf2 = 5088., 5088., 5424., 5424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 4.4 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 4400., 4400. / Name = vc_gi Station = VLBA Priority = 2 rf1 = 4576., 4576., 5076., 5076. ifname = A, C, B, D rf2 = 5088., 5088., 5588., 5588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 6100., 6100. / Name = vc_gj Station = VLBA Priority = 2 rf1 = 4576., 4576., 5376., 5376. ifname = A, C, B, D rf2 = 5088., 5088., 5888., 5888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 6.4 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 6400., 6400. / Name = vc_gk Station = VLBA Priority = 4 rf1 = 4576., 4576., 5576., 5576. ifname = A, C, B, D rf2 = 5088., 5088., 5900., 5900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 6.6 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 6600., 6600. / Name = vc_gl Station = VLBA Priority = 4 rf1 = 4576., 4576., 5600., 5600. ifname = A, C, B, D rf2 = 5088., 5088., 5924., 5924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 4.9 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 4900., 4900. / Name = vc_gm Station = VLBA Priority = 2 rf1 = 4576., 4576., 5612., 5612. ifname = A, C, B, D rf2 = 5088., 5088., 6124., 6124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 5.1 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 5100., 5100. / Name = vc_gn Station = VLBA Priority = 2 rf1 = 4576., 4576., 5912., 5912. ifname = A, C, B, D rf2 = 5088., 5088., 6424., 6424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 5.4 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 5400., 5400. / Name = vc_go Station = VLBA Priority = 2 rf1 = 4576., 4576., 6112., 6112. ifname = A, C, B, D rf2 = 5088., 5088., 6624., 6624. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 5600., 5600. / Name = vc_gr Station = VLBA Priority = 4 rf1 = 4576., 4576., 6376., 6376. ifname = A, C, B, D rf2 = 5088., 5088., 6700., 6700. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 7.4 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 7400., 7400. / Name = vc_gp Station = VLBA Priority = 2 rf1 = 4576., 4576., 6412., 6412. ifname = A, C, B, D rf2 = 5088., 5088., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 5900., 5900. / Name = vc_gs Station = VLBA Priority = 2 rf1 = 4576., 4576., 6576., 6576. ifname = A, C, B, D rf2 = 5088., 5088., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 7600., 7600. / Name = vc_gq Station = VLBA Priority = 4 rf1 = 4576., 4576., 6800., 6800. ifname = A, C, B, D rf2 = 5088., 5088., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 6100., 6100. / Name = vc_gt Station = VLBA Priority = 2 rf1 = 4576., 4576., 6876., 6876. ifname = A, C, B, D rf2 = 5088., 5088., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 7900., 7900. / Name = vc_gu Station = VLBA Priority = 2 rf1 = 4576., 4576., 7076., 7076. ifname = A, C, B, D rf2 = 5088., 5088., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 8100., 8100. / Name = vc_gv Station = VLBA Priority = 2 rf1 = 4576., 4576., 7376., 7376. ifname = A, C, B, D rf2 = 5088., 5088., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 8400., 8400. / Name = vc_gw Station = VLBA Priority = 3 rf1 = 4576., 4576., 7576., 7576. ifname = A, C, B, D rf2 = 5088., 5088., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 8600., 8600. / Name = vc_dh Station = VLBA Priority = 1 rf1 = 4612., 4612., 4876., 4876. ifname = A, C, B, D rf2 = 5124., 5124., 5388., 5388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 5900., 5900. / Name = vc_de Station = VLBA Priority = 3 rf1 = 4612., 4612., 5050., 5050. ifname = A, C, B, D rf2 = 5124., 5124., 5424., 5424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 4.4 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 4400., 4400. / Name = vc_di Station = VLBA Priority = 1 rf1 = 4612., 4612., 5076., 5076. ifname = A, C, B, D rf2 = 5124., 5124., 5588., 5588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 6100., 6100. / Name = vc_dj Station = VLBA Priority = 1 rf1 = 4612., 4612., 5376., 5376. ifname = A, C, B, D rf2 = 5124., 5124., 5888., 5888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 6.4 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 6400., 6400. / Name = vc_dk Station = VLBA Priority = 3 rf1 = 4612., 4612., 5576., 5576. ifname = A, C, B, D rf2 = 5124., 5124., 5900., 5900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 6.6 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 6600., 6600. / Name = vc_dl Station = VLBA Priority = 3 rf1 = 4612., 4612., 5600., 5600. ifname = A, C, B, D rf2 = 5124., 5124., 5924., 5924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 4.9 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 4900., 4900. / Name = vc_dm Station = VLBA Priority = 1 rf1 = 4612., 4612., 5612., 5612. ifname = A, C, B, D rf2 = 5124., 5124., 6124., 6124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 5.1 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 5100., 5100. / Name = vc_dn Station = VLBA Priority = 1 rf1 = 4612., 4612., 5912., 5912. ifname = A, C, B, D rf2 = 5124., 5124., 6424., 6424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 5.4 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 5400., 5400. / Name = vc_do Station = VLBA Priority = 1 rf1 = 4612., 4612., 6112., 6112. ifname = A, C, B, D rf2 = 5124., 5124., 6624., 6624. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 5600., 5600. / Name = vc_dr Station = VLBA Priority = 3 rf1 = 4612., 4612., 6376., 6376. ifname = A, C, B, D rf2 = 5124., 5124., 6700., 6700. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 7.4 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 7400., 7400. / Name = vc_dp Station = VLBA Priority = 1 rf1 = 4612., 4612., 6412., 6412. ifname = A, C, B, D rf2 = 5124., 5124., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 5900., 5900. / Name = vc_ds Station = VLBA Priority = 1 rf1 = 4612., 4612., 6576., 6576. ifname = A, C, B, D rf2 = 5124., 5124., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 7600., 7600. / Name = vc_dq Station = VLBA Priority = 3 rf1 = 4612., 4612., 6800., 6800. ifname = A, C, B, D rf2 = 5124., 5124., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 6100., 6100. / Name = vc_dt Station = VLBA Priority = 1 rf1 = 4612., 4612., 6876., 6876. ifname = A, C, B, D rf2 = 5124., 5124., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 7900., 7900. / Name = vc_du Station = VLBA Priority = 1 rf1 = 4612., 4612., 7076., 7076. ifname = A, C, B, D rf2 = 5124., 5124., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 8100., 8100. / Name = vc_dv Station = VLBA Priority = 1 rf1 = 4612., 4612., 7376., 7376. ifname = A, C, B, D rf2 = 5124., 5124., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 8400., 8400. / Name = vc_dw Station = VLBA Priority = 2 rf1 = 4612., 4612., 7576., 7576. ifname = A, C, B, D rf2 = 5124., 5124., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.1 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 4100., 4100., 8600., 8600. / Name = vc_he Station = VLBA Priority = 3 rf1 = 4876., 4876., 5050., 5050. ifname = A, C, B, D rf2 = 5388., 5388., 5424., 5424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 4.4 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 4400., 4400. / Name = vc_hi Station = VLBA Priority = 1 rf1 = 4876., 4876., 5076., 5076. ifname = A, C, B, D rf2 = 5388., 5388., 5588., 5588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 6100., 6100. / Name = vc_hj Station = VLBA Priority = 1 rf1 = 4876., 4876., 5376., 5376. ifname = A, C, B, D rf2 = 5388., 5388., 5888., 5888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 6.4 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 6400., 6400. / Name = vc_hk Station = VLBA Priority = 3 rf1 = 4876., 4876., 5576., 5576. ifname = A, C, B, D rf2 = 5388., 5388., 5900., 5900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 6.6 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 6600., 6600. / Name = vc_hl Station = VLBA Priority = 3 rf1 = 4876., 4876., 5600., 5600. ifname = A, C, B, D rf2 = 5388., 5388., 5924., 5924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 4.9 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 4900., 4900. / Name = vc_hm Station = VLBA Priority = 1 rf1 = 4876., 4876., 5612., 5612. ifname = A, C, B, D rf2 = 5388., 5388., 6124., 6124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 5.1 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 5100., 5100. / Name = vc_hn Station = VLBA Priority = 1 rf1 = 4876., 4876., 5912., 5912. ifname = A, C, B, D rf2 = 5388., 5388., 6424., 6424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 5.4 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 5400., 5400. / Name = vc_ho Station = VLBA Priority = 1 rf1 = 4876., 4876., 6112., 6112. ifname = A, C, B, D rf2 = 5388., 5388., 6624., 6624. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 5600., 5600. / Name = vc_hr Station = VLBA Priority = 3 rf1 = 4876., 4876., 6376., 6376. ifname = A, C, B, D rf2 = 5388., 5388., 6700., 6700. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 7.4 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 7400., 7400. / Name = vc_hp Station = VLBA Priority = 1 rf1 = 4876., 4876., 6412., 6412. ifname = A, C, B, D rf2 = 5388., 5388., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 5900., 5900. / Name = vc_hs Station = VLBA Priority = 1 rf1 = 4876., 4876., 6576., 6576. ifname = A, C, B, D rf2 = 5388., 5388., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 7600., 7600. / Name = vc_hq Station = VLBA Priority = 3 rf1 = 4876., 4876., 6800., 6800. ifname = A, C, B, D rf2 = 5388., 5388., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 6100., 6100. / Name = vc_ht Station = VLBA Priority = 1 rf1 = 4876., 4876., 6876., 6876. ifname = A, C, B, D rf2 = 5388., 5388., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 7900., 7900. / Name = vc_hu Station = VLBA Priority = 1 rf1 = 4876., 4876., 7076., 7076. ifname = A, C, B, D rf2 = 5388., 5388., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 8100., 8100. / Name = vc_hv Station = VLBA Priority = 1 rf1 = 4876., 4876., 7376., 7376. ifname = A, C, B, D rf2 = 5388., 5388., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 8400., 8400. / Name = vc_hw Station = VLBA Priority = 2 rf1 = 4876., 4876., 7576., 7576. ifname = A, C, B, D rf2 = 5388., 5388., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 8600., 8600. / Name = vc_ei Station = VLBA Priority = 3 rf1 = 5050., 5050., 5076., 5076. ifname = A, C, B, D rf2 = 5424., 5424., 5588., 5588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.4 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 4400., 4400., 6100., 6100. / Name = vc_ej Station = VLBA Priority = 3 rf1 = 5050., 5050., 5376., 5376. ifname = A, C, B, D rf2 = 5424., 5424., 5888., 5888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.4 syn(1) = 6.4 pol = RCP, LCP, RCP, LCP lo1 = 4400., 4400., 6400., 6400. / Name = vc_ek Station = VLBA Priority = 5 rf1 = 5050., 5050., 5576., 5576. ifname = A, C, B, D rf2 = 5424., 5424., 5900., 5900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.4 syn(1) = 6.6 pol = RCP, LCP, RCP, LCP lo1 = 4400., 4400., 6600., 6600. / Name = vc_el Station = VLBA Priority = 5 rf1 = 5050., 5050., 5600., 5600. ifname = A, C, B, D rf2 = 5424., 5424., 5924., 5924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.4 syn(1) = 4.9 pol = RCP, LCP, RCP, LCP lo1 = 4400., 4400., 4900., 4900. / Name = vc_em Station = VLBA Priority = 3 rf1 = 5050., 5050., 5612., 5612. ifname = A, C, B, D rf2 = 5424., 5424., 6124., 6124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.4 syn(1) = 5.1 pol = RCP, LCP, RCP, LCP lo1 = 4400., 4400., 5100., 5100. / Name = vc_en Station = VLBA Priority = 3 rf1 = 5050., 5050., 5912., 5912. ifname = A, C, B, D rf2 = 5424., 5424., 6424., 6424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.4 syn(1) = 5.4 pol = RCP, LCP, RCP, LCP lo1 = 4400., 4400., 5400., 5400. / Name = vc_eo Station = VLBA Priority = 3 rf1 = 5050., 5050., 6112., 6112. ifname = A, C, B, D rf2 = 5424., 5424., 6624., 6624. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.4 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 4400., 4400., 5600., 5600. / Name = vc_er Station = VLBA Priority = 5 rf1 = 5050., 5050., 6376., 6376. ifname = A, C, B, D rf2 = 5424., 5424., 6700., 6700. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.4 syn(1) = 7.4 pol = RCP, LCP, RCP, LCP lo1 = 4400., 4400., 7400., 7400. / Name = vc_ep Station = VLBA Priority = 3 rf1 = 5050., 5050., 6412., 6412. ifname = A, C, B, D rf2 = 5424., 5424., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.4 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 4400., 4400., 5900., 5900. / Name = vc_es Station = VLBA Priority = 3 rf1 = 5050., 5050., 6576., 6576. ifname = A, C, B, D rf2 = 5424., 5424., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.4 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 4400., 4400., 7600., 7600. / Name = vc_eq Station = VLBA Priority = 5 rf1 = 5050., 5050., 6800., 6800. ifname = A, C, B, D rf2 = 5424., 5424., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.4 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 4400., 4400., 6100., 6100. / Name = vc_et Station = VLBA Priority = 3 rf1 = 5050., 5050., 6876., 6876. ifname = A, C, B, D rf2 = 5424., 5424., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.4 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 4400., 4400., 7900., 7900. / Name = vc_eu Station = VLBA Priority = 3 rf1 = 5050., 5050., 7076., 7076. ifname = A, C, B, D rf2 = 5424., 5424., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.4 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 4400., 4400., 8100., 8100. / Name = vc_ev Station = VLBA Priority = 3 rf1 = 5050., 5050., 7376., 7376. ifname = A, C, B, D rf2 = 5424., 5424., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.4 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 4400., 4400., 8400., 8400. / Name = vc_ew Station = VLBA Priority = 4 rf1 = 5050., 5050., 7576., 7576. ifname = A, C, B, D rf2 = 5424., 5424., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.4 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 4400., 4400., 8600., 8600. / Name = vc_ij Station = VLBA Priority = 1 rf1 = 5076., 5076., 5376., 5376. ifname = A, C, B, D rf2 = 5588., 5588., 5888., 5888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 6.4 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 6400., 6400. / Name = vc_ik Station = VLBA Priority = 3 rf1 = 5076., 5076., 5576., 5576. ifname = A, C, B, D rf2 = 5588., 5588., 5900., 5900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 6.6 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 6600., 6600. / Name = vc_il Station = VLBA Priority = 3 rf1 = 5076., 5076., 5600., 5600. ifname = A, C, B, D rf2 = 5588., 5588., 5924., 5924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 4.9 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 4900., 4900. / Name = vc_im Station = VLBA Priority = 1 rf1 = 5076., 5076., 5612., 5612. ifname = A, C, B, D rf2 = 5588., 5588., 6124., 6124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 5.1 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 5100., 5100. / Name = vc_in Station = VLBA Priority = 1 rf1 = 5076., 5076., 5912., 5912. ifname = A, C, B, D rf2 = 5588., 5588., 6424., 6424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 5.4 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 5400., 5400. / Name = vc_io Station = VLBA Priority = 1 rf1 = 5076., 5076., 6112., 6112. ifname = A, C, B, D rf2 = 5588., 5588., 6624., 6624. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 5600., 5600. / Name = vc_ir Station = VLBA Priority = 3 rf1 = 5076., 5076., 6376., 6376. ifname = A, C, B, D rf2 = 5588., 5588., 6700., 6700. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 7.4 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 7400., 7400. / Name = vc_ip Station = VLBA Priority = 1 rf1 = 5076., 5076., 6412., 6412. ifname = A, C, B, D rf2 = 5588., 5588., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 5900., 5900. / Name = vc_is Station = VLBA Priority = 1 rf1 = 5076., 5076., 6576., 6576. ifname = A, C, B, D rf2 = 5588., 5588., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 7600., 7600. / Name = vc_iq Station = VLBA Priority = 3 rf1 = 5076., 5076., 6800., 6800. ifname = A, C, B, D rf2 = 5588., 5588., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 6100., 6100. / Name = vc_it Station = VLBA Priority = 1 rf1 = 5076., 5076., 6876., 6876. ifname = A, C, B, D rf2 = 5588., 5588., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 7900., 7900. / Name = vc_iu Station = VLBA Priority = 1 rf1 = 5076., 5076., 7076., 7076. ifname = A, C, B, D rf2 = 5588., 5588., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 8100., 8100. / Name = vc_iv Station = VLBA Priority = 1 rf1 = 5076., 5076., 7376., 7376. ifname = A, C, B, D rf2 = 5588., 5588., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 8400., 8400. / Name = vc_iw Station = VLBA Priority = 2 rf1 = 5076., 5076., 7576., 7576. ifname = A, C, B, D rf2 = 5588., 5588., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 8600., 8600. / Name = vc_jk Station = VLBA Priority = 3 rf1 = 5376., 5376., 5576., 5576. ifname = A, C, B, D rf2 = 5888., 5888., 5900., 5900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.4 syn(1) = 6.6 pol = RCP, LCP, RCP, LCP lo1 = 6400., 6400., 6600., 6600. / Name = vc_jl Station = VLBA Priority = 3 rf1 = 5376., 5376., 5600., 5600. ifname = A, C, B, D rf2 = 5888., 5888., 5924., 5924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.4 syn(1) = 4.9 pol = RCP, LCP, RCP, LCP lo1 = 6400., 6400., 4900., 4900. / Name = vc_jm Station = VLBA Priority = 1 rf1 = 5376., 5376., 5612., 5612. ifname = A, C, B, D rf2 = 5888., 5888., 6124., 6124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.4 syn(1) = 5.1 pol = RCP, LCP, RCP, LCP lo1 = 6400., 6400., 5100., 5100. / Name = vc_jn Station = VLBA Priority = 1 rf1 = 5376., 5376., 5912., 5912. ifname = A, C, B, D rf2 = 5888., 5888., 6424., 6424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.4 syn(1) = 5.4 pol = RCP, LCP, RCP, LCP lo1 = 6400., 6400., 5400., 5400. / Name = vc_jo Station = VLBA Priority = 1 rf1 = 5376., 5376., 6112., 6112. ifname = A, C, B, D rf2 = 5888., 5888., 6624., 6624. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.4 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 6400., 6400., 5600., 5600. / Name = vc_jr Station = VLBA Priority = 3 rf1 = 5376., 5376., 6376., 6376. ifname = A, C, B, D rf2 = 5888., 5888., 6700., 6700. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.4 syn(1) = 7.4 pol = RCP, LCP, RCP, LCP lo1 = 6400., 6400., 7400., 7400. / Name = vc_jp Station = VLBA Priority = 1 rf1 = 5376., 5376., 6412., 6412. ifname = A, C, B, D rf2 = 5888., 5888., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.4 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 6400., 6400., 5900., 5900. / Name = vc_js Station = VLBA Priority = 1 rf1 = 5376., 5376., 6576., 6576. ifname = A, C, B, D rf2 = 5888., 5888., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.4 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 6400., 6400., 7600., 7600. / Name = vc_jq Station = VLBA Priority = 3 rf1 = 5376., 5376., 6800., 6800. ifname = A, C, B, D rf2 = 5888., 5888., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.4 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 6400., 6400., 6100., 6100. / Name = vc_jt Station = VLBA Priority = 1 rf1 = 5376., 5376., 6876., 6876. ifname = A, C, B, D rf2 = 5888., 5888., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.4 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 6400., 6400., 7900., 7900. / Name = vc_ju Station = VLBA Priority = 1 rf1 = 5376., 5376., 7076., 7076. ifname = A, C, B, D rf2 = 5888., 5888., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.4 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 6400., 6400., 8100., 8100. / Name = vc_jv Station = VLBA Priority = 1 rf1 = 5376., 5376., 7376., 7376. ifname = A, C, B, D rf2 = 5888., 5888., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.4 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 6400., 6400., 8400., 8400. / Name = vc_jw Station = VLBA Priority = 2 rf1 = 5376., 5376., 7576., 7576. ifname = A, C, B, D rf2 = 5888., 5888., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.4 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 6400., 6400., 8600., 8600. / Name = vc_kl Station = VLBA Priority = 5 rf1 = 5576., 5576., 5600., 5600. ifname = A, C, B, D rf2 = 5900., 5900., 5924., 5924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.6 syn(1) = 4.9 pol = RCP, LCP, RCP, LCP lo1 = 6600., 6600., 4900., 4900. / Name = vc_km Station = VLBA Priority = 3 rf1 = 5576., 5576., 5612., 5612. ifname = A, C, B, D rf2 = 5900., 5900., 6124., 6124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.6 syn(1) = 5.1 pol = RCP, LCP, RCP, LCP lo1 = 6600., 6600., 5100., 5100. / Name = vc_kn Station = VLBA Priority = 3 rf1 = 5576., 5576., 5912., 5912. ifname = A, C, B, D rf2 = 5900., 5900., 6424., 6424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.6 syn(1) = 5.4 pol = RCP, LCP, RCP, LCP lo1 = 6600., 6600., 5400., 5400. / Name = vc_ko Station = VLBA Priority = 3 rf1 = 5576., 5576., 6112., 6112. ifname = A, C, B, D rf2 = 5900., 5900., 6624., 6624. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.6 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 6600., 6600., 5600., 5600. / Name = vc_kr Station = VLBA Priority = 5 rf1 = 5576., 5576., 6376., 6376. ifname = A, C, B, D rf2 = 5900., 5900., 6700., 6700. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.6 syn(1) = 7.4 pol = RCP, LCP, RCP, LCP lo1 = 6600., 6600., 7400., 7400. / Name = vc_kp Station = VLBA Priority = 3 rf1 = 5576., 5576., 6412., 6412. ifname = A, C, B, D rf2 = 5900., 5900., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.6 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 6600., 6600., 5900., 5900. / Name = vc_ks Station = VLBA Priority = 3 rf1 = 5576., 5576., 6576., 6576. ifname = A, C, B, D rf2 = 5900., 5900., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.6 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 6600., 6600., 7600., 7600. / Name = vc_kq Station = VLBA Priority = 5 rf1 = 5576., 5576., 6800., 6800. ifname = A, C, B, D rf2 = 5900., 5900., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.6 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 6600., 6600., 6100., 6100. / Name = vc_kt Station = VLBA Priority = 3 rf1 = 5576., 5576., 6876., 6876. ifname = A, C, B, D rf2 = 5900., 5900., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.6 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 6600., 6600., 7900., 7900. / Name = vc_ku Station = VLBA Priority = 3 rf1 = 5576., 5576., 7076., 7076. ifname = A, C, B, D rf2 = 5900., 5900., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.6 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 6600., 6600., 8100., 8100. / Name = vc_kv Station = VLBA Priority = 3 rf1 = 5576., 5576., 7376., 7376. ifname = A, C, B, D rf2 = 5900., 5900., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.6 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 6600., 6600., 8400., 8400. / Name = vc_kw Station = VLBA Priority = 4 rf1 = 5576., 5576., 7576., 7576. ifname = A, C, B, D rf2 = 5900., 5900., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.6 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 6600., 6600., 8600., 8600. / Name = vc_lm Station = VLBA Priority = 3 rf1 = 5600., 5600., 5612., 5612. ifname = A, C, B, D rf2 = 5924., 5924., 6124., 6124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.9 syn(1) = 5.1 pol = RCP, LCP, RCP, LCP lo1 = 4900., 4900., 5100., 5100. / Name = vc_ln Station = VLBA Priority = 3 rf1 = 5600., 5600., 5912., 5912. ifname = A, C, B, D rf2 = 5924., 5924., 6424., 6424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.9 syn(1) = 5.4 pol = RCP, LCP, RCP, LCP lo1 = 4900., 4900., 5400., 5400. / Name = vc_lo Station = VLBA Priority = 3 rf1 = 5600., 5600., 6112., 6112. ifname = A, C, B, D rf2 = 5924., 5924., 6624., 6624. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.9 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 4900., 4900., 5600., 5600. / Name = vc_lr Station = VLBA Priority = 5 rf1 = 5600., 5600., 6376., 6376. ifname = A, C, B, D rf2 = 5924., 5924., 6700., 6700. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.9 syn(1) = 7.4 pol = RCP, LCP, RCP, LCP lo1 = 4900., 4900., 7400., 7400. / Name = vc_lp Station = VLBA Priority = 3 rf1 = 5600., 5600., 6412., 6412. ifname = A, C, B, D rf2 = 5924., 5924., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.9 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 4900., 4900., 5900., 5900. / Name = vc_ls Station = VLBA Priority = 3 rf1 = 5600., 5600., 6576., 6576. ifname = A, C, B, D rf2 = 5924., 5924., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.9 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 4900., 4900., 7600., 7600. / Name = vc_lq Station = VLBA Priority = 5 rf1 = 5600., 5600., 6800., 6800. ifname = A, C, B, D rf2 = 5924., 5924., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.9 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 4900., 4900., 6100., 6100. / Name = vc_lt Station = VLBA Priority = 3 rf1 = 5600., 5600., 6876., 6876. ifname = A, C, B, D rf2 = 5924., 5924., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.9 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 4900., 4900., 7900., 7900. / Name = vc_lu Station = VLBA Priority = 3 rf1 = 5600., 5600., 7076., 7076. ifname = A, C, B, D rf2 = 5924., 5924., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.9 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 4900., 4900., 8100., 8100. / Name = vc_lv Station = VLBA Priority = 3 rf1 = 5600., 5600., 7376., 7376. ifname = A, C, B, D rf2 = 5924., 5924., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.9 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 4900., 4900., 8400., 8400. / Name = vc_lw Station = VLBA Priority = 4 rf1 = 5600., 5600., 7576., 7576. ifname = A, C, B, D rf2 = 5924., 5924., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 4.9 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 4900., 4900., 8600., 8600. / Name = vc_mn Station = VLBA Priority = 1 rf1 = 5612., 5612., 5912., 5912. ifname = A, C, B, D rf2 = 6124., 6124., 6424., 6424. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.1 syn(1) = 5.4 pol = RCP, LCP, RCP, LCP lo1 = 5100., 5100., 5400., 5400. / Name = vc_mo Station = VLBA Priority = 1 rf1 = 5612., 5612., 6112., 6112. ifname = A, C, B, D rf2 = 6124., 6124., 6624., 6624. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.1 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 5100., 5100., 5600., 5600. / Name = vc_mr Station = VLBA Priority = 3 rf1 = 5612., 5612., 6376., 6376. ifname = A, C, B, D rf2 = 6124., 6124., 6700., 6700. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.1 syn(1) = 7.4 pol = RCP, LCP, RCP, LCP lo1 = 5100., 5100., 7400., 7400. / Name = vc_mp Station = VLBA Priority = 1 rf1 = 5612., 5612., 6412., 6412. ifname = A, C, B, D rf2 = 6124., 6124., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.1 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 5100., 5100., 5900., 5900. / Name = vc_ms Station = VLBA Priority = 1 rf1 = 5612., 5612., 6576., 6576. ifname = A, C, B, D rf2 = 6124., 6124., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.1 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 5100., 5100., 7600., 7600. / Name = vc_mq Station = VLBA Priority = 3 rf1 = 5612., 5612., 6800., 6800. ifname = A, C, B, D rf2 = 6124., 6124., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.1 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 5100., 5100., 6100., 6100. / Name = vc_mt Station = VLBA Priority = 1 rf1 = 5612., 5612., 6876., 6876. ifname = A, C, B, D rf2 = 6124., 6124., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.1 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 5100., 5100., 7900., 7900. / Name = vc_mu Station = VLBA Priority = 1 rf1 = 5612., 5612., 7076., 7076. ifname = A, C, B, D rf2 = 6124., 6124., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.1 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 5100., 5100., 8100., 8100. / Name = vc_mv Station = VLBA Priority = 1 rf1 = 5612., 5612., 7376., 7376. ifname = A, C, B, D rf2 = 6124., 6124., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.1 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 5100., 5100., 8400., 8400. / Name = vc_mw Station = VLBA Priority = 2 rf1 = 5612., 5612., 7576., 7576. ifname = A, C, B, D rf2 = 6124., 6124., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.1 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 5100., 5100., 8600., 8600. / Name = vc_no Station = VLBA Priority = 1 rf1 = 5912., 5912., 6112., 6112. ifname = A, C, B, D rf2 = 6424., 6424., 6624., 6624. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 5.6 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 5600., 5600. / Name = vc_nr Station = VLBA Priority = 3 rf1 = 5912., 5912., 6376., 6376. ifname = A, C, B, D rf2 = 6424., 6424., 6700., 6700. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 7.4 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 7400., 7400. / Name = vc_np Station = VLBA Priority = 1 rf1 = 5912., 5912., 6412., 6412. ifname = A, C, B, D rf2 = 6424., 6424., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 5900., 5900. / Name = vc_ns Station = VLBA Priority = 1 rf1 = 5912., 5912., 6576., 6576. ifname = A, C, B, D rf2 = 6424., 6424., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 7600., 7600. / Name = vc_nq Station = VLBA Priority = 3 rf1 = 5912., 5912., 6800., 6800. ifname = A, C, B, D rf2 = 6424., 6424., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 6100., 6100. / Name = vc_nt Station = VLBA Priority = 1 rf1 = 5912., 5912., 6876., 6876. ifname = A, C, B, D rf2 = 6424., 6424., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 7900., 7900. / Name = vc_nu Station = VLBA Priority = 1 rf1 = 5912., 5912., 7076., 7076. ifname = A, C, B, D rf2 = 6424., 6424., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 8100., 8100. / Name = vc_nv Station = VLBA Priority = 1 rf1 = 5912., 5912., 7376., 7376. ifname = A, C, B, D rf2 = 6424., 6424., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 8400., 8400. / Name = vc_nw Station = VLBA Priority = 2 rf1 = 5912., 5912., 7576., 7576. ifname = A, C, B, D rf2 = 6424., 6424., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.4 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 5400., 5400., 8600., 8600. / Name = vc_or Station = VLBA Priority = 3 rf1 = 6112., 6112., 6376., 6376. ifname = A, C, B, D rf2 = 6624., 6624., 6700., 6700. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 7.4 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 7400., 7400. / Name = vc_op Station = VLBA Priority = 1 rf1 = 6112., 6112., 6412., 6412. ifname = A, C, B, D rf2 = 6624., 6624., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 5900., 5900. / Name = vc_os Station = VLBA Priority = 1 rf1 = 6112., 6112., 6576., 6576. ifname = A, C, B, D rf2 = 6624., 6624., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 7600., 7600. / Name = vc_oq Station = VLBA Priority = 3 rf1 = 6112., 6112., 6800., 6800. ifname = A, C, B, D rf2 = 6624., 6624., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 6100., 6100. / Name = vc_ot Station = VLBA Priority = 1 rf1 = 6112., 6112., 6876., 6876. ifname = A, C, B, D rf2 = 6624., 6624., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 7900., 7900. / Name = vc_ou Station = VLBA Priority = 1 rf1 = 6112., 6112., 7076., 7076. ifname = A, C, B, D rf2 = 6624., 6624., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 8100., 8100. / Name = vc_ov Station = VLBA Priority = 1 rf1 = 6112., 6112., 7376., 7376. ifname = A, C, B, D rf2 = 6624., 6624., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 8400., 8400. / Name = vc_ow Station = VLBA Priority = 2 rf1 = 6112., 6112., 7576., 7576. ifname = A, C, B, D rf2 = 6624., 6624., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.6 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 5600., 5600., 8600., 8600. / Name = vc_rp Station = VLBA Priority = 3 rf1 = 6376., 6376., 6412., 6412. ifname = A, C, B, D rf2 = 6700., 6700., 6924., 6924. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 7.4 syn(1) = 5.9 pol = RCP, LCP, RCP, LCP lo1 = 7400., 7400., 5900., 5900. / Name = vc_rs Station = VLBA Priority = 3 rf1 = 6376., 6376., 6576., 6576. ifname = A, C, B, D rf2 = 6700., 6700., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 7.4 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 7400., 7400., 7600., 7600. / Name = vc_rq Station = VLBA Priority = 5 rf1 = 6376., 6376., 6800., 6800. ifname = A, C, B, D rf2 = 6700., 6700., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 7.4 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 7400., 7400., 6100., 6100. / Name = vc_rt Station = VLBA Priority = 3 rf1 = 6376., 6376., 6876., 6876. ifname = A, C, B, D rf2 = 6700., 6700., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 7.4 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 7400., 7400., 7900., 7900. / Name = vc_ru Station = VLBA Priority = 3 rf1 = 6376., 6376., 7076., 7076. ifname = A, C, B, D rf2 = 6700., 6700., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 7.4 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 7400., 7400., 8100., 8100. / Name = vc_rv Station = VLBA Priority = 3 rf1 = 6376., 6376., 7376., 7376. ifname = A, C, B, D rf2 = 6700., 6700., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 7.4 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 7400., 7400., 8400., 8400. / Name = vc_rw Station = VLBA Priority = 4 rf1 = 6376., 6376., 7576., 7576. ifname = A, C, B, D rf2 = 6700., 6700., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 7.4 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 7400., 7400., 8600., 8600. / Name = vc_ps Station = VLBA Priority = 1 rf1 = 6412., 6412., 6576., 6576. ifname = A, C, B, D rf2 = 6924., 6924., 7088., 7088. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 7.6 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 7600., 7600. / Name = vc_pq Station = VLBA Priority = 3 rf1 = 6412., 6412., 6800., 6800. ifname = A, C, B, D rf2 = 6924., 6924., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 6100., 6100. / Name = vc_pt Station = VLBA Priority = 1 rf1 = 6412., 6412., 6876., 6876. ifname = A, C, B, D rf2 = 6924., 6924., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 7900., 7900. / Name = vc_pu Station = VLBA Priority = 1 rf1 = 6412., 6412., 7076., 7076. ifname = A, C, B, D rf2 = 6924., 6924., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 8100., 8100. / Name = vc_pv Station = VLBA Priority = 1 rf1 = 6412., 6412., 7376., 7376. ifname = A, C, B, D rf2 = 6924., 6924., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 8400., 8400. / Name = vc_pw Station = VLBA Priority = 2 rf1 = 6412., 6412., 7576., 7576. ifname = A, C, B, D rf2 = 6924., 6924., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 5.9 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 5900., 5900., 8600., 8600. / Name = vc_sq Station = VLBA Priority = 3 rf1 = 6576., 6576., 6800., 6800. ifname = A, C, B, D rf2 = 7088., 7088., 7124., 7124. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 7.6 syn(1) = 6.1 pol = RCP, LCP, RCP, LCP lo1 = 7600., 7600., 6100., 6100. / Name = vc_st Station = VLBA Priority = 1 rf1 = 6576., 6576., 6876., 6876. ifname = A, C, B, D rf2 = 7088., 7088., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 7.6 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 7600., 7600., 7900., 7900. / Name = vc_su Station = VLBA Priority = 1 rf1 = 6576., 6576., 7076., 7076. ifname = A, C, B, D rf2 = 7088., 7088., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 7.6 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 7600., 7600., 8100., 8100. / Name = vc_sv Station = VLBA Priority = 1 rf1 = 6576., 6576., 7376., 7376. ifname = A, C, B, D rf2 = 7088., 7088., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 7.6 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 7600., 7600., 8400., 8400. / Name = vc_sw Station = VLBA Priority = 2 rf1 = 6576., 6576., 7576., 7576. ifname = A, C, B, D rf2 = 7088., 7088., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 7.6 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 7600., 7600., 8600., 8600. / Name = vc_qt Station = VLBA Priority = 3 rf1 = 6800., 6800., 6876., 6876. ifname = A, C, B, D rf2 = 7124., 7124., 7388., 7388. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 7.9 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 7900., 7900. / Name = vc_qu Station = VLBA Priority = 3 rf1 = 6800., 6800., 7076., 7076. ifname = A, C, B, D rf2 = 7124., 7124., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 8100., 8100. / Name = vc_qv Station = VLBA Priority = 3 rf1 = 6800., 6800., 7376., 7376. ifname = A, C, B, D rf2 = 7124., 7124., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 8400., 8400. / Name = vc_qw Station = VLBA Priority = 4 rf1 = 6800., 6800., 7576., 7576. ifname = A, C, B, D rf2 = 7124., 7124., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 6.1 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 6100., 6100., 8600., 8600. / Name = vc_tu Station = VLBA Priority = 1 rf1 = 6876., 6876., 7076., 7076. ifname = A, C, B, D rf2 = 7388., 7388., 7588., 7588. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 7.9 syn(1) = 8.1 pol = RCP, LCP, RCP, LCP lo1 = 7900., 7900., 8100., 8100. / Name = vc_tv Station = VLBA Priority = 1 rf1 = 6876., 6876., 7376., 7376. ifname = A, C, B, D rf2 = 7388., 7388., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 7.9 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 7900., 7900., 8400., 8400. / Name = vc_tw Station = VLBA Priority = 2 rf1 = 6876., 6876., 7576., 7576. ifname = A, C, B, D rf2 = 7388., 7388., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 7.9 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 7900., 7900., 8600., 8600. / Name = vc_uv Station = VLBA Priority = 1 rf1 = 7076., 7076., 7376., 7376. ifname = A, C, B, D rf2 = 7588., 7588., 7888., 7888. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 8.1 syn(1) = 8.4 pol = RCP, LCP, RCP, LCP lo1 = 8100., 8100., 8400., 8400. / Name = vc_uw Station = VLBA Priority = 2 rf1 = 7076., 7076., 7576., 7576. ifname = A, C, B, D rf2 = 7588., 7588., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 8.1 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 8100., 8100., 8600., 8600. / Name = vc_vw Station = VLBA Priority = 2 rf1 = 7376., 7376., 7576., 7576. ifname = A, C, B, D rf2 = 7888., 7888., 7900., 7900. fe = '6cm', '6cm', '6cm', '6cm' syn(2) = 8.4 syn(1) = 8.6 pol = RCP, LCP, RCP, LCP lo1 = 8400., 8400., 8600., 8600. / ! 4cm This receiver can split RCP and route a second version ! through the LCP electronics with a separate LO. This ! option is given with the S/X groups below. It is for ! very wide spanned bandwidths. ! If both 13 and 4 cm channels are present, the ellipsoid ! and dichroic will be used. If only 4 cm is present, the ! ellipsoid will be swung out of the way for improved ! performance. ! Receiver: 7920 - 8880 MHz ! LO Filters: 7150 - 9650 ! Maximum range: 7700 - 9050 ! Good range: 7900 - 8900 ! Both upper and lower first LO sidebands can be used. ! The groups below use upper except where the LO would ! be in the receiver passband. ! The pure 4 cm groups below are probably not needed (the S/X ! groups cover most of the same ground), but are here for ! clarity. Also, the extreme frequency ranges are not covered ! under the S/X options. Name = v4cm_1 Station = VLBA Priority = 1 rf1 = 7700, 7700 ifname = B, D rf2 = 8124, 8124 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7100, 7100 syn(1) = 7.1 / Name = v4cm_2 Station = VLBA Priority = 0 rf1 = 7912, 7912 ifname = B, D rf2 = 8424, 8424 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7400, 7400 syn(1) = 7.4 / Name = v4cm_3 Station = VLBA Priority = 0 rf1 = 8112, 8112 ifname = B, D rf2 = 8624, 8624 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7600, 7600 syn(1) = 7.6 / Name = v4cm_4 Station = VLBA Priority = 2 rf1 = 8412, 8412 ifname = B, D rf2 = 8924, 8924 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7900, 7900 syn(1) = 7.9 note = 'LO is in receiver band.' / ! This is almost the same frequency range as v4cm_3, but ! allows matching non-VLBA stations that want a high LO. ! Note that with the PFB, the bands will not be the same ! as in v4cm_3 as there is a 36 MHz shift. Name = v4cm_5 Station = VLBA Priority = 1 rf1 = 8076, 8076 ifname = B, D rf2 = 8588, 8588 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 9100, 9100 syn(1) = 9.1 / Name = v4cm_6 Station = VLBA Priority = 0 rf1 = 8376, 8376 ifname = B, D rf2 = 8888, 8888 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 9400, 9400 syn(1) = 9.4 / Name = v4cm_7 Station = VLBA Priority = 0 rf1 = 8576, 8576 ifname = B, D rf2 = 9050, 9050 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 9600, 9600 syn(1) = 9.6 / ! S/X - Not quite an exhaustive set. ! Give all S/X modes slightly worse priority so that ! they will not be used for single frequency obs. ! Note that the frequency ranges do not take into ! account the S band RFI filters (2200-2400 GHz). Name = vsx_11 Station = VLBA Priority = 2 rf1 = 1876, 1876, 7912, 7912 ifname = A, C, B, D rf2 = 2388, 2388, 8424, 8424 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, LCP lo1 = 2900, 2900, 7400, 7400 syn(1) = 7.4 syn(2) = 2.9 / Name = vsx_12 Station = VLBA Priority = 2 rf1 = 1876, 1876, 8112, 8112 ifname = A, C , B , D rf2 = 2388, 2388, 8624, 8624 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, LCP lo1 = 2900, 2900, 7600, 7600 syn(1) = 7.6 syn(2) = 2.9 / ! Add this one because it is being used, but discourage it. Name = vsx_13 Station = VLBA Priority = 4 rf1 = 1876, 1876, 8412, 8412 ifname = A, C , B , D rf2 = 2388, 2388, 8924, 8924 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, LCP lo1 = 2900, 2900, 7900, 7900 syn(1) = 7.9 syn(2) = 2.9 note='Poor LO choice at 4cm - LO in receiver RF - consider 9.4 GHz' / Name = vsx_14 Station = VLBA Priority = 2 rf1 = 1876, 1876, 8376, 8376 ifname = A, C, B, D rf2 = 2388, 2388, 8888, 8888 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, LCP lo1 = 2900, 2900, 9400, 9400 syn(1) = 9.4 syn(2) = 2.9 / Name = vsx_15 Station = VLBA Priority = 2 rf1 = 1876, 1876, 8576, 8576 ifname = A, C, B, D rf2 = 2388, 2388, 9050, 9050 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, LCP lo1 = 2900, 2900, 9600, 9600 syn(1) = 9.6 syn(2) = 2.9 / Name = vsx_21 Station = VLBA Priority = 2 rf1 = 2076, 2076, 7912, 7912 ifname = A, C, B, D rf2 = 2588, 2588, 8424, 8424 fe = '13cm', '13cm','4cm', '4cm' pol = RCP, LCP, RCP, LCP lo1 = 3100, 3100, 7400, 7400 syn(1) = 7.4 syn(2) = 3.1 / Name = vsx_22 Station = VLBA Priority = 2 rf1 = 2076, 2076, 8112, 8112 ifname = A, C, B, D rf2 = 2588, 2588, 8624, 8624 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, LCP lo1 = 3100, 3100, 7600, 7600 syn(1) = 7.6 syn(2) = 3.1 / ! Add this one because it is being used, but discourage it. Name = vsx_23 Station = VLBA Priority = 4 rf1 = 2076, 2076, 8412, 8412 ifname = A, C , B , D rf2 = 2588, 2588, 8924, 8924 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, LCP lo1 = 3100, 3100, 7900, 7900 syn(1) = 7.9 syn(2) = 3.1 note='Poor LO choice at 4cm - LO in receiver RF - consider 9.4 GHz' / Name = vsx_24 Station = VLBA Priority = 2 rf1 = 2076, 2076, 8376, 8376 ifname = A, C, B, D rf2 = 2588, 2588, 8888, 8888 fe = '13cm', '13cm','4cm', '4cm' pol = RCP, LCP, RCP, LCP lo1 = 3100, 3100, 9400, 9400 syn(1) = 9.4 syn(2) = 3.1 / Name = vsx_25 Station = VLBA Priority = 2 rf1 = 2076, 2076, 8576, 8576 ifname = A, C, B, D rf2 = 2588, 2588, 9050, 9050 fe = '13cm', '13cm','4cm', '4cm' pol = RCP, LCP, RCP, LCP lo1 = 3100, 3100, 9600, 9600 syn(1) = 9.6 syn(2) = 3.1 / ! S/X With wide X - Not quite exhaustive. Includes only ! combinations with IF B in the lower part of X band and IF D in the ! upper. A full set would be very large. ! Give these even worse priority so they won't be used unless ! necessary. Name = vsx_1w Station = VLBA Priority = 3 rf1 = 1876, 1876, 7912, 8376 ifname = A, C, B, D rf2 = 2388, 2388, 8424, 8888 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, RCP lo1 = 2900, 2900, 7400, 9400 syn(1) = 7.4 syn(2) = 2.9 syn(3) = 9.4 dualx / Name = vsx_2w Station = VLBA Priority = 3 rf1 = 1876, 1876, 8112, 8376 ifname = A, C , B , D rf2 = 2388, 2388, 8624, 8888 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, RCP lo1 = 2900, 2900, 7600, 9400 syn(1) = 7.6 syn(2) = 2.9 syn(3) = 9.4 dualx / Name = vsx_3w Station = VLBA Priority = 3 rf1 = 2076, 2076, 7912, 8376 ifname = A, C, B, D rf2 = 2588, 2588, 8424, 8888 fe = '13cm', '13cm','4cm', '4cm' pol = RCP, LCP, RCP, RCP lo1 = 3100, 3100, 7400, 9400 syn(1) = 7.4 syn(2) = 3.1 syn(3) = 9.4 dualx / Name = vsx_4w Station = VLBA Priority = 3 rf1 = 2076, 2076, 8112, 8376 ifname = A, C, B, D rf2 = 2588, 2588, 8624, 8888 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, RCP lo1 = 3100, 3100, 7600, 9400 syn(1) = 7.6 syn(2) = 3.1 syn(3) = 9.4 dualx / Name = vsx_5w Station = VLBA Priority = 3 rf1 = 1876, 1876, 7912, 8576 ifname = A, C, B, D rf2 = 2388, 2388, 8424, 9050 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, RCP lo1 = 2900, 2900, 7400, 9600 syn(1) = 7.4 syn(2) = 2.9 syn(3) = 9.6 dualx / ! These two may be wanted for RDV at least allow a test. ! There is could be trouble with the 8.1 GHz LO at 500 MHz for the ! lower X band IF. Name = vsx_5wb Station = VLBA Priority = 4 rf1 = 1876, 1876, 8112, 8612 ifname = A, C, B, D rf2 = 2388, 2388, 8624, 9124 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, RCP lo1 = 2900, 2900, 7600, 8100 syn(1) = 7.6 syn(2) = 2.9 syn(3) = 8.1 dualx / Name = vsx_5wc Station = VLBA Priority = 4 rf1 = 2076, 1076, 8112, 8612 ifname = A, C, B, D rf2 = 2588, 2588, 8624, 9124 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, RCP lo1 = 3100, 3100, 7600, 8100 syn(1) = 7.6 syn(2) = 3.1 syn(3) = 8.1 dualx / ! Back to our regular programming. Name = vsx_6w Station = VLBA Priority = 3 rf1 = 1876, 1876, 8112, 8576 ifname = A, C , B , D rf2 = 2388, 2388, 8624, 9050 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, RCP lo1 = 2900, 2900, 7600, 9600 syn(1) = 7.6 syn(2) = 2.9 syn(3) = 9.6 dualx / Name = vsx_7w Station = VLBA Priority = 3 rf1 = 2076, 2076, 7912, 8576 ifname = A, C, B, D rf2 = 2588, 2588, 8424, 9050 fe = '13cm', '13cm','4cm', '4cm' pol = RCP, LCP, RCP, RCP lo1 = 3100, 3100, 7400, 9600 syn(1) = 7.4 syn(2) = 3.1 syn(3) = 9.6 dualx / Name = vsx_8w Station = VLBA Priority = 3 rf1 = 2076, 2076, 8112, 8576 ifname = A, C, B, D rf2 = 2588, 2588, 8624, 9050 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, RCP lo1 = 3100, 3100, 7600, 9600 syn(1) = 7.6 syn(2) = 3.1 syn(3) = 9.6 dualx / ! 2 cm The IF converter for this receiver has 4 RF filters. ! The on-line system chooses which to use based on the ! frequency of channel 1. ch1rf1 and ch1rf2 are the ! required frequency ranges for channel one for the given ! filter. The on-line system always assumes an upper ! sideband first mix ! ! There is a Radio Astronomy band from 15.35 to 15.4 GHz ! that is shared with other passive services. ! ! Receiver Nominal Channel 1 Max range Good range ! filter filter range range ! 1: 11820 - 12980 0 - 12900 11800 - 13000 12100 - 12950 ! 2: 12820 - 13980 12900 - 13900 12800 - 14000 12850 - 13950 ! 3: 13820 - 14980 13900 - 14900 13800 - 15000 13850 - 14950 ! 4: 14770 - 15630 14900 - inf 14700 - 15700 14800 - 15500 ! LO filter: 11000 - 16000 MHz ! Filter 1: Name = v2cm_a1 Station = VLBA Priority = 1 rf1 = 11800, 11800 ifname = B, D rf2 = 12124, 12124 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 11100, 11100 syn(1) = 11.1 ch1rf1 = 11000, 11000 ch1rf2 = 12900, 12900 note = 'First 2cm filter' / Name = v2cm_a2 Station = VLBA Priority = 0 rf1 = 11912, 11912 ifname = B, D rf2 = 12424, 12424 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 11400, 11400 syn(1) = 11.4 ch1rf1 = 11000, 11000 ch1rf2 = 12900, 12900 note = 'First 2cm filter' / Name = v2cm_a3 Station = VLBA Priority = 0 rf1 = 12112, 12112 ifname = B, D rf2 = 12624, 12624 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 11600, 11600 syn(1) = 11.6 ch1rf1 = 11900, 11900 ch1rf2 = 12900, 12900 note = 'First 2cm filter' / Name = v2cm_a4 Station = VLBA Priority = 0 rf1 = 12412, 12412 ifname = B, D rf2 = 12924, 12924 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 11900, 11900 syn(1) = 11.9 ch1rf1 = 11900, 11900 ch1rf2 = 12900, 12900 note = 'First 2cm filter' / Name = v2cm_a5 Station = VLBA Priority = 1 rf1 = 12612, 12612 ifname = B, D rf2 = 13000, 13000 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 12100, 12100 syn(1) = 12.1 ch1rf1 = 11900, 11900 ch1rf2 = 12900, 12900 note = 'First 2cm filter' / ! Filter 2: Name = v2cm_b1 Station = VLBA Priority = 1 rf1 = 12800, 12800 ifname = B, D rf2 = 13124, 13124 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 12100, 12100 syn(1) = 12.1 ch1rf1 = 12900, 12900 ch1rf2 = 13900, 13900 note = 'Second 2cm filter' / Name = v2cm_b2 Station = VLBA Priority = 0 rf1 = 12912, 12912 ifname = B, D rf2 = 13424, 13424 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 12400, 12400 syn(1) = 12.4 ch1rf1 = 12900, 12900 ch1rf2 = 13900, 13900 note = 'Second 2cm filter' / Name = v2cm_b3 Station = VLBA Priority = 0 rf1 = 13112, 13112 ifname = B, D rf2 = 13624, 13624 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 12600, 12600 syn(1) = 12.6 ch1rf1 = 12900, 12900 ch1rf2 = 13900, 13900 note = 'Second 2cm filter' / Name = v2cm_b4 Station = VLBA Priority = 0 rf1 = 13412, 13412 ifname = B, D rf2 = 13924, 13924 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 12900, 12900 syn(1) = 12.9 ch1rf1 = 12900, 12900 ch1rf2 = 13900, 13900 note = 'Second 2cm filter' / Name = v2cm_b5 Station = VLBA Priority = 1 rf1 = 13612, 13612 ifname = B, D rf2 = 14000, 14000 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 13100, 13100 syn(1) = 13.1 ch1rf1 = 12900, 12900 ch1rf2 = 13900, 13900 note = 'Second 2cm filter' / ! Third filter Name = v2cm_c1 Station = VLBA Priority = 1 rf1 = 13800, 13800 ifname = B, D rf2 = 14124, 14124 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 13100, 13100 syn(1) = 13.1 ch1rf1 = 13900, 13900 ch1rf2 = 14900, 14900 note = 'Third 2cm filter' / Name = v2cm_c2 Station = VLBA Priority = 0 rf1 = 13912, 13912 ifname = B, D rf2 = 14424, 14424 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 13400, 13400 syn(1) = 13.4 ch1rf1 = 13900, 13900 ch1rf2 = 14900, 14900 note = 'Third 2cm filter' / Name = v2cm_c3 Station = VLBA Priority = 0 rf1 = 14112, 14112 ifname = B, D rf2 = 14624, 14624 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 13600, 13600 syn(1) = 13.6 ch1rf1 = 13900, 13900 ch1rf2 = 14900, 14900 note = 'Third 2cm filter' / Name = v2cm_c4 Station = VLBA Priority = 0 rf1 = 14412, 14412 ifname = B, D rf2 = 14924, 14924 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 13900, 13900 syn(1) = 13.9 ch1rf1 = 13900, 13900 ch1rf2 = 14900, 14900 note = 'Third 2cm filter' / Name = v2cm_c5 Station = VLBA Priority = 1 rf1 = 14612, 14612 ifname = B, D rf2 = 15000, 15000 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 14100, 14100 syn(1) = 14.1 ch1rf1 = 13900, 13900 ch1rf2 = 14900, 14900 note = 'Third 2cm filter' / ! Fourth filter. Name = v2cm_d1 Station = VLBA Priority = 1 rf1 = 14700, 14700 ifname = B, D rf2 = 15124, 15124 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 14100, 14100 syn(1) = 14.1 ch1rf1 = 14900, 14900 ch1rf2 = 15900, 15900 note = 'Fourth 2cm filter' / Name = v2cm_d2 Station = VLBA Priority = 0 rf1 = 14912, 14912 ifname = B, D rf2 = 15424, 15424 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 14400, 14400 syn(1) = 14.4 ch1rf1 = 14900, 14900 ch1rf2 = 15900, 15900 note = 'Fourth 2cm filter' / Name = v2cm_d3 Station = VLBA Priority = 0 rf1 = 15112, 15112 ifname = B, D rf2 = 15624, 15624 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 14600, 14600 syn(1) = 14.6 ch1rf1 = 14900, 14900 ch1rf2 = 15900, 15900 note = 'Fourth 2cm filter' / Name = v2cm_d4 Station = VLBA Priority = 1 rf1 = 15412, 15412 ifname = B, D rf2 = 15924, 15924 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 14900, 14900 syn(1) = 14.9 ch1rf1 = 14900, 14900 ch1rf2 = 15900, 15900 note = 'Fourth 2cm filter. High IF freqs will be bad.' / ! 1 cm - At 1 cm, are two synthesizers and many combinations, ! some of which give the same frequency. ! First LO filter: 12000 - 14500 ! First IF filter: 9300 - 10200 ! Second LO filter: 7150 - 9650 ! Maximum range: 20500 - 25300 ! Good range: 21400 - 24300 ! Maximum 2-16 GHz synthesizer setting is 15.9 (16.1?) GHz. ! Reasonable second LO's that pass full 500 MHz bands of the ! right sideband are: 8.9 and 9.1 GHz. Anything else has ! the potential to loose signal at the first IF filter. ! However, a lower LO might be needed to reach extreme ! frequencies. ! ! Naming convention. ! eg v1cm_a3 The last 2 letters according to: ! Syn(1) = 8.6 (x), 8.9 (a), 9.1 (b), 9.4 (c) ! Syn(3) = 11.4 (-1), 11.6 (0), 11.9 (1), 12.1 (2), 12.4 (3), ! 12.6 (4), 12.9 (5), 13.1 (6), 13.4 (7), 13.6 (8), ! 13.9 (9), 14.1 (10), 14.4 (11), 14.6 (12), 14.9 (13) Name = v1cm_x-1 Station = VLBA Priority = 5 rf1 = 20512, 20512 ifname = B, D rf2 = 21024, 21024 fe = '1cm', '1cm' syn(1) = 8.6 pol = RCP, LCP lo1 = 20000, 20000 syn(3) = 11.4 note='Nominal IF cutoff at 20700 MHz. Syn3 600 MHz below LO filter' / Name = v1cm_x0 Station = VLBA Priority = 5 rf1 = 20712, 20712 ifname = B, D rf2 = 21224, 21224 fe = '1cm', '1cm' syn(1) = 8.6 pol = RCP, LCP lo1 = 20200, 20200 syn(3) = 11.6 note='Nominal IF cutoff at 20900 MHz. Syn3 400 MHz below LO filter' / Name = v1cm_x1 Station = VLBA Priority = 4 rf1 = 21012, 21012 ifname = B, D rf2 = 21524, 21524 fe = '1cm', '1cm' syn(1) = 8.6 pol = RCP, LCP lo1 = 20500, 20500 syn(3) = 11.9 note='Nominal IF cutoff at 21200 MHz Syn3 100 MHz below LO filter' / Name = v1cm_b0 Station = VLBA Priority = 4 rf1 = 21212, 21212 ifname = B, D rf2 = 21724, 21724 fe = '1cm', '1cm' syn(1) = 9.1 pol = RCP, LCP lo1 = 20700, 20700 syn(3) = 11.6 note='Syn3 is 400 MHz below first LO filter.' / Name = v1cm_a1 Station = VLBA Priority = 1 rf1 = 21312, 21312 ifname = B, D rf2 = 21824, 21824 fe = '1cm', '1cm' syn(1) = 8.9 pol = RCP, LCP lo1 = 20800, 20800 syn(3) = 11.9 note='Syn3 is 100 MHz below first LO filter.' / ! Can get with 9.1, 11.9, but poor on first LO filter. Name = v1cm_a2 Station = VLBA Priority = 0 rf1 = 21512, 21512 ifname = B, D rf2 = 22024, 22024 fe = '1cm', '1cm' syn(1) = 8.9 pol = RCP, LCP lo1 = 21000, 21000 syn(3) = 12.1 / Name = v1cm_b2 Station = VLBA Priority = 0 rf1 = 21712, 21712 ifname = B, D rf2 = 22224, 22224 fe = '1cm', '1cm' syn(1) = 9.1 pol = RCP, LCP lo1 = 21200, 21200 syn(3) = 12.1 / Name = v1cm_a3 Station = VLBA Priority = 0 rf1 = 21812, 21812 ifname = B, D rf2 = 22324, 22324 fe = '1cm', '1cm' syn(1) = 8.9 pol = RCP, LCP lo1 = 21300, 21300 syn(3) = 12.4 / Name = v1cm_b3 Station = VLBA Priority = 0 rf1 = 22012, 22012 ifname = B, D rf2 = 22524, 22524 fe = '1cm', '1cm' syn(1) = 9.1 pol = RCP, LCP lo1 = 21500, 21500 syn(3) = 12.4 / Name = v1cm_a4 Station = VLBA Priority = 0 rf1 = 22012, 22012 ifname = B, D rf2 = 22524, 22524 fe = '1cm', '1cm' syn(1) = 8.9 pol = RCP, LCP lo1 = 21500, 21500 syn(3) = 12.6 / Name = v1cm_b4 Station = VLBA Priority = 0 rf1 = 22212, 22212 ifname = B, D rf2 = 22724, 22724 fe = '1cm', '1cm' syn(1) = 9.1 pol = RCP, LCP lo1 = 21700, 21700 syn(3) = 12.6 / Name = v1cm_a5 Station = VLBA Priority = 0 rf1 = 22312, 22312 ifname = B, D rf2 = 22824, 22824 fe = '1cm', '1cm' syn(1) = 8.9 pol = RCP, LCP lo1 = 21800, 21800 syn(3) = 12.9 / Name = v1cm_a6 Station = VLBA Priority = 0 rf1 = 22512, 22512 ifname = B, D rf2 = 23024, 23024 fe = '1cm', '1cm' syn(1) = 8.9 pol = RCP, LCP lo1 = 22000, 22000 syn(3) = 13.1 / Name = v1cm_b5 Station = VLBA Priority = 0 rf1 = 22512, 22512 ifname = B, D rf2 = 23024, 23024 fe = '1cm', '1cm' syn(1) = 9.1 pol = RCP, LCP lo1 = 22000, 22000 syn(3) = 12.9 / Name = v1cm_b6 Station = VLBA Priority = 0 rf1 = 22712, 22712 ifname = B, D rf2 = 23224, 23224 fe = '1cm', '1cm' syn(1) = 9.1 pol = RCP, LCP lo1 = 22200, 22200 syn(3) = 13.1 / Name = v1cm_a7 Station = VLBA Priority = 0 rf1 = 22812, 22812 ifname = B, D rf2 = 23324, 23324 fe = '1cm', '1cm' syn(1) = 8.9 pol = RCP, LCP lo1 = 22300, 22300 syn(3) = 13.4 / Name = v1cm_b7 Station = VLBA Priority = 0 rf1 = 23012, 23012 ifname = B, D rf2 = 23524, 23524 fe = '1cm', '1cm' syn(1) = 9.1 pol = RCP, LCP lo1 = 22500, 22500 syn(3) = 13.4 / Name = v1cm_a8 Station = VLBA Priority = 0 rf1 = 23012, 23012 ifname = B, D rf2 = 23524, 23524 fe = '1cm', '1cm' syn(1) = 8.9 pol = RCP, LCP lo1 = 22500, 22500 syn(3) = 13.6 / Name = v1cm_b8 Station = VLBA Priority = 0 rf1 = 23212, 23212 ifname = B, D rf2 = 23724, 23724 fe = '1cm', '1cm' syn(1) = 9.1 pol = RCP, LCP lo1 = 22700, 22700 syn(3) = 13.6 / Name = v1cm_a9 Station = VLBA Priority = 0 rf1 = 23312, 23312 ifname = B, D rf2 = 23824, 23824 fe = '1cm', '1cm' syn(1) = 8.9 pol = RCP, LCP lo1 = 22800, 22800 syn(3) = 13.9 / Name = v1cm_a10 Station = VLBA Priority = 0 rf1 = 23512, 23512 ifname = B, D rf2 = 24024, 24024 fe = '1cm', '1cm' syn(1) = 8.9 pol = RCP, LCP lo1 = 23000, 23000 syn(3) = 14.1 / Name = v1cm_b9 Station = VLBA Priority = 0 rf1 = 23512, 23512 ifname = B, D rf2 = 24024, 24024 fe = '1cm', '1cm' syn(1) = 9.1 pol = RCP, LCP lo1 = 23000, 23000 syn(3) = 13.9 / Name = v1cm_b10 Station = VLBA Priority = 0 rf1 = 23712, 23712 ifname = B, D rf2 = 24224, 24224 fe = '1cm', '1cm' syn(1) = 9.1 pol = RCP, LCP lo1 = 23200, 23200 syn(3) = 14.1 / Name = v1cm_a11 Station = VLBA Priority = 0 rf1 = 23812, 23812 ifname = B, D rf2 = 24324, 24324 fe = '1cm', '1cm' syn(1) = 8.9 pol = RCP, LCP lo1 = 23300, 23300 syn(3) = 14.4 / Name = v1cm_b11 Station = VLBA Priority = 0 rf1 = 24012, 24012 ifname = B, D rf2 = 24524, 24524 fe = '1cm', '1cm' syn(1) = 9.1 pol = RCP, LCP lo1 = 23500, 23500 syn(3) = 14.4 / Name = v1cm_a12 Station = VLBA Priority = 0 rf1 = 24012, 24012 ifname = B, D rf2 = 24524, 24524 fe = '1cm', '1cm' syn(1) = 8.9 pol = RCP, LCP lo1 = 23500, 23500 syn(3) = 14.6 / Name = v1cm_b12 Station = VLBA Priority = 0 rf1 = 24212, 24212 ifname = B, D rf2 = 24724, 24724 fe = '1cm', '1cm' syn(1) = 9.1 pol = RCP, LCP lo1 = 23700, 23700 syn(3) = 14.6 / ! Below here, the first LO is a ways outside the filter. Name = v1cm_a13 Station = VLBA Priority = 1 rf1 = 24312, 24312 ifname = B, D rf2 = 24824, 24824 fe = '1cm', '1cm' syn(1) = 8.9 pol = RCP, LCP lo1 = 23800, 23800 syn(3) = 14.9 / Name = v1cm_b13 Station = VLBA Priority = 1 rf1 = 24512, 24512 ifname = B, D rf2 = 25024, 25024 fe = '1cm', '1cm' syn(1) = 9.1 pol = RCP, LCP lo1 = 24000, 24000 syn(3) = 14.9 / ! Memo 51 data look a bit like the one below is getting a wrong ! sideband or something, but I don't think it should. Name = v1cm_c13 Station = VLBA Priority = 2 rf1 = 24812, 24812 ifname = B, D rf2 = 25324, 25324 fe = '1cm', '1cm' syn(1) = 9.4 pol = RCP, LCP lo1 = 24300, 24300 syn(3) = 14.9 / ! VLBA 7mm The first LO is Syn(3) * 3. The second is Syn(2) ! Receiver nominal: 40.0 - 45.0 GHz ! LO filter before 3X multiply: 10.75 - 12.25 ! First IF filter: 7.70 - 9.10 ! First IF filter: 7.90 - 8.90 (KP, FD) ! Second LO filter: 7.15 - 9.65 ! Maximum range: 37.6 - 46.2 ! Good range: 39.2 - 45.2 ! Upper and lower sidebands at the second mix could be used. ! The on-line system did not originally support lower sidebands, ! but supposedly it does now. ! Possible second synthesizer settings: ! 7.4, 7.6 Good. ! 9.4, 9.6 Good. ! ! The following are possible, but are not used in the setups. ! 7.1 GHz IF will cut off below 600 MHz. Is used ! in some projects. ! 7.9 Probably good. LO in IF band. ! 8.1 Risk getting some lower sideband. ! ! Give the 9.4 and 9.6 second LO options lower priority ! because they give lower sideband mixes. This should be ok ! now (wasn't for a while), but is not all that well tested. ! ! Naming conventions: eg v7mm_b3 ! syn(2) = 7.1 (a), 7.4 (b), 7.6 (c), 7.9 (d), 8.1 (e), ! 9.1 (f), 9.4 (g), 9.6 (h), 9.9 (i) ! syn(3) = 9.9 (1), 10.1 (2), 10.4 (3), 10.6 (4), 10.9 (5), ! 11.1 (6), 11.4 (7), 11.6 (8), 11.9 (9), 12.1 (10), ! 12.4 (11), 12.6 (12) Name = v7mm_b1 Station = VLBA Priority = 1 rf1 = 37612, 37612 ifname = A, C rf2 = 38124, 38124 fe = '7mm', '7mm' syn(2) = 7.4 pol = RCP, LCP lo1 = 37100, 37100 syn(3) = 9.9 / Name = v7mm_c1 Station = VLBA Priority = 1 rf1 = 37812, 37812 ifname = A, C rf2 = 38324, 38324 fe = '7mm', '7mm' syn(2) = 7.6 pol = RCP, LCP lo1 = 37300, 37300 syn(3) = 9.9 / Name = v7mm_b2 Station = VLBA Priority = 1 rf1 = 38212, 38212 ifname = A, C rf2 = 38724, 38724 fe = '7mm', '7mm' syn(2) = 7.4 pol = RCP, LCP lo1 = 37700, 37700 syn(3) = 10.1 / Name = v7mm_c2 Station = VLBA Priority = 1 rf1 = 38412, 38412 ifname = A, C rf2 = 38924, 38924 fe = '7mm', '7mm' syn(2) = 7.6 pol = RCP, LCP lo1 = 37900, 37900 syn(3) = 10.1 / Name = v7mm_g2 Station = VLBA Priority = 2 rf1 = 38676, 38676 ifname = A, C rf2 = 39188, 39188 fe = '7mm', '7mm' syn(2) = 9.4 pol = RCP, LCP lo1 = 39700, 39700 syn(3) = 10.1 / Name = v7mm_h2 Station = VLBA Priority = 2 rf1 = 38876, 38876 ifname = A, C rf2 = 39388, 39388 fe = '7mm', '7mm' syn(2) = 9.6 pol = RCP, LCP lo1 = 39900, 39900 syn(3) = 10.1 / Name = v7mm_b3 Station = VLBA Priority = 1 rf1 = 39112, 39112 ifname = A, C rf2 = 39624, 39624 fe = '7mm', '7mm' syn(2) = 7.4 pol = RCP, LCP lo1 = 38600, 38600 syn(3) = 10.4 / Name = v7mm_c3 Station = VLBA Priority = 1 rf1 = 39312, 39312 ifname = A, C rf2 = 39824, 39824 fe = '7mm', '7mm' syn(2) = 7.6 pol = RCP, LCP lo1 = 38800, 38800 syn(3) = 10.4 / Name = v7mm_g3 Station = VLBA Priority = 2 rf1 = 39576, 39576 ifname = A, C rf2 = 40088, 40088 fe = '7mm', '7mm' syn(2) = 9.4 pol = RCP, LCP lo1 = 40600, 40600 syn(3) = 10.4 / Name = v7mm_b4 Station = VLBA Priority = 0 rf1 = 39712, 39712 ifname = A, C rf2 = 40224, 40224 fe = '7mm', '7mm' syn(2) = 7.4 pol = RCP, LCP lo1 = 39200, 39200 syn(3) = 10.6 / Name = v7mm_h3 Station = VLBA Priority = 2 rf1 = 39776, 39776 ifname = A, C rf2 = 40288, 40288 fe = '7mm', '7mm' syn(2) = 9.6 pol = RCP, LCP lo1 = 40800, 40800 syn(3) = 10.4 / Name = v7mm_c4 Station = VLBA Priority = 0 rf1 = 39912, 39912 ifname = A, C rf2 = 40424, 40424 fe = '7mm', '7mm' syn(2) = 7.6 pol = RCP, LCP lo1 = 39400, 39400 syn(3) = 10.6 / Name = v7mm_g4 Station = VLBA Priority = 2 rf1 = 40176, 40176 ifname = A, C rf2 = 40688, 40688 fe = '7mm', '7mm' syn(2) = 9.4 pol = RCP, LCP lo1 = 41200, 41200 syn(3) = 10.6 / Name = v7mm_h4 Station = VLBA Priority = 2 rf1 = 40376, 40376 ifname = A, C rf2 = 40888, 40888 fe = '7mm', '7mm' syn(2) = 9.6 pol = RCP, LCP lo1 = 41400, 41400 syn(3) = 10.6 / Name = v7mm_b5 Station = VLBA Priority = 0 rf1 = 40612, 40612 ifname = A, C rf2 = 41124, 41124 fe = '7mm', '7mm' syn(2) = 7.4 pol = RCP, LCP lo1 = 40100, 40100 syn(3) = 10.9 / Name = v7mm_c5 Station = VLBA Priority = 0 rf1 = 40812, 40812 ifname = A, C rf2 = 41324, 41324 fe = '7mm', '7mm' syn(2) = 7.6 pol = RCP, LCP lo1 = 40300, 40300 syn(3) = 10.9 / Name = v7mm_g5 Station = VLBA Priority = 2 rf1 = 41076, 41076 ifname = A, C rf2 = 41588, 41588 fe = '7mm', '7mm' syn(2) = 9.4 pol = RCP, LCP lo1 = 42100, 42100 syn(3) = 10.9 / Name = v7mm_b6 Station = VLBA Priority = 0 rf1 = 41212, 41212 ifname = A, C rf2 = 41724, 41724 fe = '7mm', '7mm' syn(2) = 7.4 pol = RCP, LCP lo1 = 40700, 40700 syn(3) = 11.1 / Name = v7mm_h5 Station = VLBA Priority = 2 rf1 = 41276, 41276 ifname = A, C rf2 = 41788, 41788 fe = '7mm', '7mm' syn(2) = 9.6 pol = RCP, LCP lo1 = 42300, 42300 syn(3) = 10.9 / Name = v7mm_c6 Station = VLBA Priority = 0 rf1 = 41412, 41412 ifname = A, C rf2 = 41924, 41924 fe = '7mm', '7mm' syn(2) = 7.6 pol = RCP, LCP lo1 = 40900, 40900 syn(3) = 11.1 / Name = v7mm_g6 Station = VLBA Priority = 4 rf1 = 41676, 41676 ifname = A, C rf2 = 42188, 42188 fe = '7mm', '7mm' syn(2) = 9.4 pol = RCP, LCP lo1 = 42700, 42700 syn(3) = 11.1 note = 'Lower sideband second mix - on-line system may have problems.' / Name = v7mm_h6 Station = VLBA Priority = 2 rf1 = 41876, 41876 ifname = A, C rf2 = 42388, 42388 fe = '7mm', '7mm' syn(2) = 9.6 pol = RCP, LCP lo1 = 42900, 42900 syn(3) = 11.1 / Name = v7mm_b6 Station = VLBA Priority = 0 rf1 = 42112, 42112 ifname = A, C rf2 = 42624, 42624 fe = '7mm', '7mm' syn(2) = 7.4 pol = RCP, LCP lo1 = 41600, 41600 syn(3) = 11.4 / Name = v7mm_c7 Station = VLBA Priority = 0 rf1 = 42312, 42312 ifname = A, C rf2 = 42824, 42824 fe = '7mm', '7mm' syn(2) = 7.6 pol = RCP, LCP lo1 = 41800, 41800 syn(3) = 11.4 / Name = v7mm_g7 Station = VLBA Priority = 2 rf1 = 42576, 42576 ifname = A, C rf2 = 43088, 43088 fe = '7mm', '7mm' syn(2) = 9.4 pol = RCP, LCP lo1 = 43600, 43600 syn(3) = 11.4 / Name = v7mm_b8 Station = VLBA Priority = 0 rf1 = 42712, 42712 ifname = A, C rf2 = 43224, 43224 fe = '7mm', '7mm' syn(2) = 7.4 pol = RCP, LCP lo1 = 42200, 42200 syn(3) = 11.6 / Name = v7mm_h7 Station = VLBA Priority = 2 rf1 = 42776, 42776 ifname = A, C rf2 = 43288, 43288 fe = '7mm', '7mm' syn(2) = 9.6 pol = RCP, LCP lo1 = 43800, 43800 syn(3) = 11.4 / Name = v7mm_c8 Station = VLBA Priority = 0 rf1 = 42912, 42912 ifname = A, C rf2 = 43424, 43424 fe = '7mm', '7mm' syn(2) = 7.6 pol = RCP, LCP lo1 = 42400, 42400 syn(3) = 11.6 / Name = v7mm_g8 Station = VLBA Priority = 2 rf1 = 43176, 43176 ifname = A, C rf2 = 43688, 43688 fe = '7mm', '7mm' syn(2) = 9.4 pol = RCP, LCP lo1 = 44200, 44200 syn(3) = 11.6 / Name = v7mm_h8 Station = VLBA Priority = 2 rf1 = 43376, 43376 ifname = A, C rf2 = 43888, 43888 fe = '7mm', '7mm' syn(2) = 9.6 pol = RCP, LCP lo1 = 44400, 44400 syn(3) = 11.6 / Name = v7mm_b9 Station = VLBA Priority = 0 rf1 = 43612, 43612 ifname = A, C rf2 = 44124, 44124 fe = '7mm', '7mm' syn(2) = 7.4 pol = RCP, LCP lo1 = 43100, 43100 syn(3) = 11.9 / Name = v7mm_c9 Station = VLBA Priority = 0 rf1 = 43812, 43812 ifname = A, C rf2 = 44324, 44324 fe = '7mm', '7mm' syn(2) = 7.6 pol = RCP, LCP lo1 = 43300, 43300 syn(3) = 11.9 / Name = v7mm_g9 Station = VLBA Priority = 2 rf1 = 44076, 44076 ifname = A, C rf2 = 44588, 44588 fe = '7mm', '7mm' syn(2) = 9.4 pol = RCP, LCP lo1 = 45100, 45100 syn(3) = 11.9 / Name = v7mm_b10 Station = VLBA Priority = 0 rf1 = 44212, 44212 ifname = A, C rf2 = 44724, 44724 fe = '7mm', '7mm' syn(2) = 7.4 pol = RCP, LCP lo1 = 43700, 43700 syn(3) = 12.1 / Name = v7mm_h9 Station = VLBA Priority = 2 rf1 = 44276, 44276 ifname = A, C rf2 = 44788, 44788 fe = '7mm', '7mm' syn(2) = 9.6 pol = RCP, LCP lo1 = 45300, 45300 syn(3) = 11.9 / Name = v7mm_c10 Station = VLBA Priority = 0 rf1 = 44412, 44412 ifname = A, C rf2 = 44924, 44924 fe = '7mm', '7mm' syn(2) = 7.6 pol = RCP, LCP lo1 = 43900, 43900 syn(3) = 12.1 / Name = v7mm_g10 Station = VLBA Priority = 2 rf1 = 44676, 44676 ifname = A, C rf2 = 45188, 45188 fe = '7mm', '7mm' syn(2) = 9.4 pol = RCP, LCP lo1 = 45700, 45700 syn(3) = 12.1 / Name = v7mm_h10 Station = VLBA Priority = 2 rf1 = 44876, 44876 ifname = A, C rf2 = 45388, 45388 fe = '7mm', '7mm' syn(2) = 9.6 pol = RCP, LCP lo1 = 45900, 45900 syn(3) = 12.1 / Name = v7mm_b11 Station = VLBA Priority = 1 rf1 = 45112, 45112 ifname = A, C rf2 = 45624, 45624 fe = '7mm', '7mm' syn(2) = 7.4 pol = RCP, LCP lo1 = 44600, 44600 syn(3) = 12.4 / Name = v7mm_c11 Station = VLBA Priority = 1 rf1 = 45312, 45312 ifname = A, C rf2 = 45824, 45824 fe = '7mm', '7mm' syn(2) = 7.6 pol = RCP, LCP lo1 = 44800, 44800 syn(3) = 12.4 / Name = v7mm_g11 Station = VLBA Priority = 2 rf1 = 45576, 45576 ifname = A, C rf2 = 46088, 46088 fe = '7mm', '7mm' syn(2) = 9.4 pol = RCP, LCP lo1 = 46600, 46600 syn(3) = 12.4 / Name = v7mm_b12 Station = VLBA Priority = 1 rf1 = 45712, 45712 ifname = A, C rf2 = 46224, 46224 fe = '7mm', '7mm' syn(2) = 7.4 pol = RCP, LCP lo1 = 45200, 45200 syn(3) = 12.6 / Name = v7mm_h11 Station = VLBA Priority = 2 rf1 = 45776, 45776 ifname = A, C rf2 = 46288, 46288 fe = '7mm', '7mm' syn(2) = 9.6 pol = RCP, LCP lo1 = 46800, 46800 syn(3) = 12.4 note = ' Upper end of receiver at 46200. ' / Name = v7mm_c12 Station = VLBA Priority = 1 rf1 = 45912, 45912 ifname = A, C rf2 = 46424, 46424 fe = '7mm', '7mm' syn(2) = 7.6 pol = RCP, LCP lo1 = 45400, 45400 syn(3) = 12.6 note = ' Upper end of receiver at 46200. ' / ! VLBA at 3mm ! The nominal band for the 86 GHz receiver is 80-96 GHz. The ! RF is mixed in the receiver with an LO that is synthesizer 3 ! multiplied by 6. The intermediate IF thus generated is sent ! to the 2 cm IF converter where it can pass through any of the ! 4 filters (Clark, 2004mar01). Care should be taken to not ! be on the boundaries between those filters. ! ! Keep Synthesizer 3 in range 10.9 to 13.6 (Hayward, Mar. 1, ! 2004). Hayward suggests picking a first IF close to 14.2 GHz. ! ! The 2 cm IF converter filter is chosen based on the intermediate ! IF frequency of the first channel in the same manner as for 2 cm. ! See the description of the 2 cm system above for details. ! ! By leaving out the second LO (synthesizer 1) settings that ! have IF's that cross the filter boundaries, we avoid ! confusion and insure full 500 MHz bands all the time. This ! means leaving out the N.1 (where N is 12, 13, or 14) MHz LO ! settings. We are left with a good set of allowed settings ! that allow any frequency to be reached. The set below has ! had the duplicates removed, favoring sets with the IF near ! 14.2 GHz. Also the RF ranges are restricted to fall in the ! range 79.7 to 96.2 GHz. ! ! The 2cm converter covers: ! Max range: 11800 - 15700 ! Good range: 12100 - 15500 ! Allowed LO settings: 11.1 - 14.9 ! Used settings: 11.9, 12.4, 12.6, 12.9, ! 13.4, 13.6, 13.9, 14.4 ! Recommended values of syn(3): ! 10.9, 11.1, 11.4, 11.6, 11.9, 12.1, ! 12.4, 12.6, 12.9, 13.1, 13.4, 13.6 ! After 6X multiple, the 0.3 GHz gaps become 1.8 GHz. ! ! ! Here is the old "standard" setup (Pre 2004mar01). It turns out ! not to be very good because the IF is at the edge of a 2cm IF ! converter filter. The 500 MHz IF was in 14600-15100 which should ! work for most cases, but could lose the top 100 MHz in a spread ! IF case. ! Name = v3mm_a Station = VLBA Priority = 0 ! rf1 = 86000, 86000 ifname = B, D ! rf2 = 86500, 86500 fe = '3mm', '3mm' syn(1) = 14.1 ! pol = RCP, LCP lo1 = 85500, 85500 syn(3) = 11.9 ! / ! ! The following setups were calculated by MAKEFREQ, a program kept ! with the development version of SCHED in the RELATED_CODE subdirectory ! The names are derived based on the LO settings, but they have been ! sorted here in order of RF frequency. ! Name = v3mm_be Station = VLBA Priority = 0 rf1 = 79712., 79712. ifname = B, D rf2 = 80224., 80224. fe = '3mm', '3mm' syn(1) = 12.6 pol = RCP, LCP lo1 = 79200., 79200. syn(3) = 11.1 ! First IF = 13112. to 13624. / Name = v3mm_ai Station = VLBA Priority = 0 rf1 = 79812., 79812. ifname = B, D rf2 = 80324., 80324. fe = '3mm', '3mm' syn(1) = 13.9 pol = RCP, LCP lo1 = 79300., 79300. syn(3) = 10.9 ! First IF = 14412. to 14924. / Name = v3mm_bf Station = VLBA Priority = 0 rf1 = 80012., 80012. ifname = B, D rf2 = 80524., 80524. fe = '3mm', '3mm' syn(1) = 12.9 pol = RCP, LCP lo1 = 79500., 79500. syn(3) = 11.1 ! First IF = 13412. to 13924. / Name = v3mm_aj Station = VLBA Priority = 0 rf1 = 80312., 80312. ifname = B, D rf2 = 80824., 80824. fe = '3mm', '3mm' syn(1) = 14.4 pol = RCP, LCP lo1 = 79800., 79800. syn(3) = 10.9 ! First IF = 14912. to 15424. / Name = v3mm_ak Station = VLBA Priority = 0 rf1 = 80512., 80512. ifname = B, D rf2 = 81024., 81024. fe = '3mm', '3mm' syn(1) = 14.6 pol = RCP, LCP lo1 = 80000., 80000. syn(3) = 10.9 ! First IF = 15112. to 15624. / Name = v3mm_bg Station = VLBA Priority = 0 rf1 = 80512., 80512. ifname = B, D rf2 = 81024., 81024. fe = '3mm', '3mm' syn(1) = 13.4 pol = RCP, LCP lo1 = 80000., 80000. syn(3) = 11.1 ! First IF = 13912. to 14424. / Name = v3mm_bh Station = VLBA Priority = 0 rf1 = 80712., 80712. ifname = B, D rf2 = 81224., 81224. fe = '3mm', '3mm' syn(1) = 13.6 pol = RCP, LCP lo1 = 80200., 80200. syn(3) = 11.1 ! First IF = 14112. to 14624. / Name = v3mm_cc Station = VLBA Priority = 0 rf1 = 80812., 80812. ifname = B, D rf2 = 81324., 81324. fe = '3mm', '3mm' syn(1) = 11.9 pol = RCP, LCP lo1 = 80300., 80300. syn(3) = 11.4 ! First IF = 12412. to 12924. / Name = v3mm_bi Station = VLBA Priority = 0 rf1 = 81012., 81012. ifname = B, D rf2 = 81524., 81524. fe = '3mm', '3mm' syn(1) = 13.9 pol = RCP, LCP lo1 = 80500., 80500. syn(3) = 11.1 ! First IF = 14412. to 14924. / Name = v3mm_cd Station = VLBA Priority = 0 rf1 = 81312., 81312. ifname = B, D rf2 = 81824., 81824. fe = '3mm', '3mm' syn(1) = 12.4 pol = RCP, LCP lo1 = 80800., 80800. syn(3) = 11.4 ! First IF = 12912. to 13424. / Name = v3mm_ce Station = VLBA Priority = 0 rf1 = 81512., 81512. ifname = B, D rf2 = 82024., 82024. fe = '3mm', '3mm' syn(1) = 12.6 pol = RCP, LCP lo1 = 81000., 81000. syn(3) = 11.4 ! First IF = 13112. to 13624. / Name = v3mm_bj Station = VLBA Priority = 0 rf1 = 81512., 81512. ifname = B, D rf2 = 82024., 82024. fe = '3mm', '3mm' syn(1) = 14.4 pol = RCP, LCP lo1 = 81000., 81000. syn(3) = 11.1 ! First IF = 14912. to 15424. / Name = v3mm_bk Station = VLBA Priority = 0 rf1 = 81712., 81712. ifname = B, D rf2 = 82224., 82224. fe = '3mm', '3mm' syn(1) = 14.6 pol = RCP, LCP lo1 = 81200., 81200. syn(3) = 11.1 ! First IF = 15112. to 15624. / Name = v3mm_cf Station = VLBA Priority = 0 rf1 = 81812., 81812. ifname = B, D rf2 = 82324., 82324. fe = '3mm', '3mm' syn(1) = 12.9 pol = RCP, LCP lo1 = 81300., 81300. syn(3) = 11.4 ! First IF = 13412. to 13924. / Name = v3mm_dc Station = VLBA Priority = 0 rf1 = 82012., 82012. ifname = B, D rf2 = 82524., 82524. fe = '3mm', '3mm' syn(1) = 11.9 pol = RCP, LCP lo1 = 81500., 81500. syn(3) = 11.6 ! First IF = 12412. to 12924. / Name = v3mm_cg Station = VLBA Priority = 0 rf1 = 82312., 82312. ifname = B, D rf2 = 82824., 82824. fe = '3mm', '3mm' syn(1) = 13.4 pol = RCP, LCP lo1 = 81800., 81800. syn(3) = 11.4 ! First IF = 13912. to 14424. / Name = v3mm_ch Station = VLBA Priority = 0 rf1 = 82512., 82512. ifname = B, D rf2 = 83024., 83024. fe = '3mm', '3mm' syn(1) = 13.6 pol = RCP, LCP lo1 = 82000., 82000. syn(3) = 11.4 ! First IF = 14112. to 14624. / Name = v3mm_dd Station = VLBA Priority = 0 rf1 = 82512., 82512. ifname = B, D rf2 = 83024., 83024. fe = '3mm', '3mm' syn(1) = 12.4 pol = RCP, LCP lo1 = 82000., 82000. syn(3) = 11.6 ! First IF = 12912. to 13424. / Name = v3mm_de Station = VLBA Priority = 0 rf1 = 82712., 82712. ifname = B, D rf2 = 83224., 83224. fe = '3mm', '3mm' syn(1) = 12.6 pol = RCP, LCP lo1 = 82200., 82200. syn(3) = 11.6 ! First IF = 13112. to 13624. / Name = v3mm_ci Station = VLBA Priority = 0 rf1 = 82812., 82812. ifname = B, D rf2 = 83324., 83324. fe = '3mm', '3mm' syn(1) = 13.9 pol = RCP, LCP lo1 = 82300., 82300. syn(3) = 11.4 ! First IF = 14412. to 14924. / Name = v3mm_df Station = VLBA Priority = 0 rf1 = 83012., 83012. ifname = B, D rf2 = 83524., 83524. fe = '3mm', '3mm' syn(1) = 12.9 pol = RCP, LCP lo1 = 82500., 82500. syn(3) = 11.6 ! First IF = 13412. to 13924. / Name = v3mm_cj Station = VLBA Priority = 0 rf1 = 83312., 83312. ifname = B, D rf2 = 83824., 83824. fe = '3mm', '3mm' syn(1) = 14.4 pol = RCP, LCP lo1 = 82800., 82800. syn(3) = 11.4 ! First IF = 14912. to 15424. / Name = v3mm_ck Station = VLBA Priority = 0 rf1 = 83512., 83512. ifname = B, D rf2 = 84024., 84024. fe = '3mm', '3mm' syn(1) = 14.6 pol = RCP, LCP lo1 = 83000., 83000. syn(3) = 11.4 ! First IF = 15112. to 15624. / Name = v3mm_dg Station = VLBA Priority = 0 rf1 = 83512., 83512. ifname = B, D rf2 = 84024., 84024. fe = '3mm', '3mm' syn(1) = 13.4 pol = RCP, LCP lo1 = 83000., 83000. syn(3) = 11.6 ! First IF = 13912. to 14424. / Name = v3mm_dh Station = VLBA Priority = 0 rf1 = 83712., 83712. ifname = B, D rf2 = 84224., 84224. fe = '3mm', '3mm' syn(1) = 13.6 pol = RCP, LCP lo1 = 83200., 83200. syn(3) = 11.6 ! First IF = 14112. to 14624. / Name = v3mm_ec Station = VLBA Priority = 0 rf1 = 83812., 83812. ifname = B, D rf2 = 84324., 84324. fe = '3mm', '3mm' syn(1) = 11.9 pol = RCP, LCP lo1 = 83300., 83300. syn(3) = 11.9 ! First IF = 12412. to 12924. / Name = v3mm_di Station = VLBA Priority = 0 rf1 = 84012., 84012. ifname = B, D rf2 = 84524., 84524. fe = '3mm', '3mm' syn(1) = 13.9 pol = RCP, LCP lo1 = 83500., 83500. syn(3) = 11.6 ! First IF = 14412. to 14924. / Name = v3mm_ed Station = VLBA Priority = 0 rf1 = 84312., 84312. ifname = B, D rf2 = 84824., 84824. fe = '3mm', '3mm' syn(1) = 12.4 pol = RCP, LCP lo1 = 83800., 83800. syn(3) = 11.9 ! First IF = 12912. to 13424. / Name = v3mm_ee Station = VLBA Priority = 0 rf1 = 84512., 84512. ifname = B, D rf2 = 85024., 85024. fe = '3mm', '3mm' syn(1) = 12.6 pol = RCP, LCP lo1 = 84000., 84000. syn(3) = 11.9 ! First IF = 13112. to 13624. / Name = v3mm_dj Station = VLBA Priority = 0 rf1 = 84512., 84512. ifname = B, D rf2 = 85024., 85024. fe = '3mm', '3mm' syn(1) = 14.4 pol = RCP, LCP lo1 = 84000., 84000. syn(3) = 11.6 ! First IF = 14912. to 15424. / Name = v3mm_dk Station = VLBA Priority = 0 rf1 = 84712., 84712. ifname = B, D rf2 = 85224., 85224. fe = '3mm', '3mm' syn(1) = 14.6 pol = RCP, LCP lo1 = 84200., 84200. syn(3) = 11.6 ! First IF = 15112. to 15624. / Name = v3mm_ef Station = VLBA Priority = 0 rf1 = 84812., 84812. ifname = B, D rf2 = 85324., 85324. fe = '3mm', '3mm' syn(1) = 12.9 pol = RCP, LCP lo1 = 84300., 84300. syn(3) = 11.9 ! First IF = 13412. to 13924. / Name = v3mm_fc Station = VLBA Priority = 0 rf1 = 85012., 85012. ifname = B, D rf2 = 85524., 85524. fe = '3mm', '3mm' syn(1) = 11.9 pol = RCP, LCP lo1 = 84500., 84500. syn(3) = 12.1 ! First IF = 12412. to 12924. / Name = v3mm_eg Station = VLBA Priority = 0 rf1 = 85312., 85312. ifname = B, D rf2 = 85824., 85824. fe = '3mm', '3mm' syn(1) = 13.4 pol = RCP, LCP lo1 = 84800., 84800. syn(3) = 11.9 ! First IF = 13912. to 14424. / Name = v3mm_eh Station = VLBA Priority = 0 rf1 = 85512., 85512. ifname = B, D rf2 = 86024., 86024. fe = '3mm', '3mm' syn(1) = 13.6 pol = RCP, LCP lo1 = 85000., 85000. syn(3) = 11.9 ! First IF = 14112. to 14624. / Name = v3mm_fd Station = VLBA Priority = 0 rf1 = 85512., 85512. ifname = B, D rf2 = 86024., 86024. fe = '3mm', '3mm' syn(1) = 12.4 pol = RCP, LCP lo1 = 85000., 85000. syn(3) = 12.1 ! First IF = 12912. to 13424. / Name = v3mm_fe Station = VLBA Priority = 0 rf1 = 85712., 85712. ifname = B, D rf2 = 86224., 86224. fe = '3mm', '3mm' syn(1) = 12.6 pol = RCP, LCP lo1 = 85200., 85200. syn(3) = 12.1 ! First IF = 13112. to 13624. / Name = v3mm_ei Station = VLBA Priority = 0 rf1 = 85812., 85812. ifname = B, D rf2 = 86324., 86324. fe = '3mm', '3mm' syn(1) = 13.9 pol = RCP, LCP lo1 = 85300., 85300. syn(3) = 11.9 ! First IF = 14412. to 14924. / Name = v3mm_ff Station = VLBA Priority = 0 rf1 = 86012., 86012. ifname = B, D rf2 = 86524., 86524. fe = '3mm', '3mm' syn(1) = 12.9 pol = RCP, LCP lo1 = 85500., 85500. syn(3) = 12.1 ! First IF = 13412. to 13924. / Name = v3mm_ej Station = VLBA Priority = 0 rf1 = 86312., 86312. ifname = B, D rf2 = 86824., 86824. fe = '3mm', '3mm' syn(1) = 14.4 pol = RCP, LCP lo1 = 85800., 85800. syn(3) = 11.9 ! First IF = 14912. to 15424. / Name = v3mm_ek Station = VLBA Priority = 0 rf1 = 86512., 86512. ifname = B, D rf2 = 87024., 87024. fe = '3mm', '3mm' syn(1) = 14.6 pol = RCP, LCP lo1 = 86000., 86000. syn(3) = 11.9 ! First IF = 15112. to 15624. / Name = v3mm_fg Station = VLBA Priority = 0 rf1 = 86512., 86512. ifname = B, D rf2 = 87024., 87024. fe = '3mm', '3mm' syn(1) = 13.4 pol = RCP, LCP lo1 = 86000., 86000. syn(3) = 12.1 ! First IF = 13912. to 14424. / Name = v3mm_fh Station = VLBA Priority = 0 rf1 = 86712., 86712. ifname = B, D rf2 = 87224., 87224. fe = '3mm', '3mm' syn(1) = 13.6 pol = RCP, LCP lo1 = 86200., 86200. syn(3) = 12.1 ! First IF = 14112. to 14624. / Name = v3mm_gc Station = VLBA Priority = 0 rf1 = 86812., 86812. ifname = B, D rf2 = 87324., 87324. fe = '3mm', '3mm' syn(1) = 11.9 pol = RCP, LCP lo1 = 86300., 86300. syn(3) = 12.4 ! First IF = 12412. to 12924. / Name = v3mm_fi Station = VLBA Priority = 0 rf1 = 87012., 87012. ifname = B, D rf2 = 87524., 87524. fe = '3mm', '3mm' syn(1) = 13.9 pol = RCP, LCP lo1 = 86500., 86500. syn(3) = 12.1 ! First IF = 14412. to 14924. / Name = v3mm_gd Station = VLBA Priority = 0 rf1 = 87312., 87312. ifname = B, D rf2 = 87824., 87824. fe = '3mm', '3mm' syn(1) = 12.4 pol = RCP, LCP lo1 = 86800., 86800. syn(3) = 12.4 ! First IF = 12912. to 13424. / Name = v3mm_ge Station = VLBA Priority = 0 rf1 = 87512., 87512. ifname = B, D rf2 = 88024., 88024. fe = '3mm', '3mm' syn(1) = 12.6 pol = RCP, LCP lo1 = 87000., 87000. syn(3) = 12.4 ! First IF = 13112. to 13624. / Name = v3mm_fj Station = VLBA Priority = 0 rf1 = 87512., 87512. ifname = B, D rf2 = 88024., 88024. fe = '3mm', '3mm' syn(1) = 14.4 pol = RCP, LCP lo1 = 87000., 87000. syn(3) = 12.1 ! First IF = 14912. to 15424. / Name = v3mm_fk Station = VLBA Priority = 0 rf1 = 87712., 87712. ifname = B, D rf2 = 88224., 88224. fe = '3mm', '3mm' syn(1) = 14.6 pol = RCP, LCP lo1 = 87200., 87200. syn(3) = 12.1 ! First IF = 15112. to 15624. / Name = v3mm_gf Station = VLBA Priority = 0 rf1 = 87812., 87812. ifname = B, D rf2 = 88324., 88324. fe = '3mm', '3mm' syn(1) = 12.9 pol = RCP, LCP lo1 = 87300., 87300. syn(3) = 12.4 ! First IF = 13412. to 13924. / Name = v3mm_hc Station = VLBA Priority = 0 rf1 = 88012., 88012. ifname = B, D rf2 = 88524., 88524. fe = '3mm', '3mm' syn(1) = 11.9 pol = RCP, LCP lo1 = 87500., 87500. syn(3) = 12.6 ! First IF = 12412. to 12924. / Name = v3mm_gg Station = VLBA Priority = 0 rf1 = 88312., 88312. ifname = B, D rf2 = 88824., 88824. fe = '3mm', '3mm' syn(1) = 13.4 pol = RCP, LCP lo1 = 87800., 87800. syn(3) = 12.4 ! First IF = 13912. to 14424. / Name = v3mm_gh Station = VLBA Priority = 0 rf1 = 88512., 88512. ifname = B, D rf2 = 89024., 89024. fe = '3mm', '3mm' syn(1) = 13.6 pol = RCP, LCP lo1 = 88000., 88000. syn(3) = 12.4 ! First IF = 14112. to 14624. / Name = v3mm_hd Station = VLBA Priority = 0 rf1 = 88512., 88512. ifname = B, D rf2 = 89024., 89024. fe = '3mm', '3mm' syn(1) = 12.4 pol = RCP, LCP lo1 = 88000., 88000. syn(3) = 12.6 ! First IF = 12912. to 13424. / Name = v3mm_he Station = VLBA Priority = 0 rf1 = 88712., 88712. ifname = B, D rf2 = 89224., 89224. fe = '3mm', '3mm' syn(1) = 12.6 pol = RCP, LCP lo1 = 88200., 88200. syn(3) = 12.6 ! First IF = 13112. to 13624. / Name = v3mm_gi Station = VLBA Priority = 0 rf1 = 88812., 88812. ifname = B, D rf2 = 89324., 89324. fe = '3mm', '3mm' syn(1) = 13.9 pol = RCP, LCP lo1 = 88300., 88300. syn(3) = 12.4 ! First IF = 14412. to 14924. / Name = v3mm_hf Station = VLBA Priority = 0 rf1 = 89012., 89012. ifname = B, D rf2 = 89524., 89524. fe = '3mm', '3mm' syn(1) = 12.9 pol = RCP, LCP lo1 = 88500., 88500. syn(3) = 12.6 ! First IF = 13412. to 13924. / Name = v3mm_gj Station = VLBA Priority = 0 rf1 = 89312., 89312. ifname = B, D rf2 = 89824., 89824. fe = '3mm', '3mm' syn(1) = 14.4 pol = RCP, LCP lo1 = 88800., 88800. syn(3) = 12.4 ! First IF = 14912. to 15424. / Name = v3mm_gk Station = VLBA Priority = 0 rf1 = 89512., 89512. ifname = B, D rf2 = 90024., 90024. fe = '3mm', '3mm' syn(1) = 14.6 pol = RCP, LCP lo1 = 89000., 89000. syn(3) = 12.4 ! First IF = 15112. to 15624. / Name = v3mm_hg Station = VLBA Priority = 0 rf1 = 89512., 89512. ifname = B, D rf2 = 90024., 90024. fe = '3mm', '3mm' syn(1) = 13.4 pol = RCP, LCP lo1 = 89000., 89000. syn(3) = 12.6 ! First IF = 13912. to 14424. / Name = v3mm_hh Station = VLBA Priority = 0 rf1 = 89712., 89712. ifname = B, D rf2 = 90224., 90224. fe = '3mm', '3mm' syn(1) = 13.6 pol = RCP, LCP lo1 = 89200., 89200. syn(3) = 12.6 ! First IF = 14112. to 14624. / Name = v3mm_ic Station = VLBA Priority = 0 rf1 = 89812., 89812. ifname = B, D rf2 = 90324., 90324. fe = '3mm', '3mm' syn(1) = 11.9 pol = RCP, LCP lo1 = 89300., 89300. syn(3) = 12.9 ! First IF = 12412. to 12924. / Name = v3mm_hi Station = VLBA Priority = 0 rf1 = 90012., 90012. ifname = B, D rf2 = 90524., 90524. fe = '3mm', '3mm' syn(1) = 13.9 pol = RCP, LCP lo1 = 89500., 89500. syn(3) = 12.6 ! First IF = 14412. to 14924. / Name = v3mm_id Station = VLBA Priority = 0 rf1 = 90312., 90312. ifname = B, D rf2 = 90824., 90824. fe = '3mm', '3mm' syn(1) = 12.4 pol = RCP, LCP lo1 = 89800., 89800. syn(3) = 12.9 ! First IF = 12912. to 13424. / Name = v3mm_ie Station = VLBA Priority = 0 rf1 = 90512., 90512. ifname = B, D rf2 = 91024., 91024. fe = '3mm', '3mm' syn(1) = 12.6 pol = RCP, LCP lo1 = 90000., 90000. syn(3) = 12.9 ! First IF = 13112. to 13624. / Name = v3mm_hj Station = VLBA Priority = 0 rf1 = 90512., 90512. ifname = B, D rf2 = 91024., 91024. fe = '3mm', '3mm' syn(1) = 14.4 pol = RCP, LCP lo1 = 90000., 90000. syn(3) = 12.6 ! First IF = 14912. to 15424. / Name = v3mm_hk Station = VLBA Priority = 0 rf1 = 90712., 90712. ifname = B, D rf2 = 91224., 91224. fe = '3mm', '3mm' syn(1) = 14.6 pol = RCP, LCP lo1 = 90200., 90200. syn(3) = 12.6 ! First IF = 15112. to 15624. / Name = v3mm_if Station = VLBA Priority = 0 rf1 = 90812., 90812. ifname = B, D rf2 = 91324., 91324. fe = '3mm', '3mm' syn(1) = 12.9 pol = RCP, LCP lo1 = 90300., 90300. syn(3) = 12.9 ! First IF = 13412. to 13924. / Name = v3mm_jc Station = VLBA Priority = 0 rf1 = 91012., 91012. ifname = B, D rf2 = 91524., 91524. fe = '3mm', '3mm' syn(1) = 11.9 pol = RCP, LCP lo1 = 90500., 90500. syn(3) = 13.1 ! First IF = 12412. to 12924. / Name = v3mm_ig Station = VLBA Priority = 0 rf1 = 91312., 91312. ifname = B, D rf2 = 91824., 91824. fe = '3mm', '3mm' syn(1) = 13.4 pol = RCP, LCP lo1 = 90800., 90800. syn(3) = 12.9 ! First IF = 13912. to 14424. / Name = v3mm_ih Station = VLBA Priority = 0 rf1 = 91512., 91512. ifname = B, D rf2 = 92024., 92024. fe = '3mm', '3mm' syn(1) = 13.6 pol = RCP, LCP lo1 = 91000., 91000. syn(3) = 12.9 ! First IF = 14112. to 14624. / Name = v3mm_jd Station = VLBA Priority = 0 rf1 = 91512., 91512. ifname = B, D rf2 = 92024., 92024. fe = '3mm', '3mm' syn(1) = 12.4 pol = RCP, LCP lo1 = 91000., 91000. syn(3) = 13.1 ! First IF = 12912. to 13424. / Name = v3mm_je Station = VLBA Priority = 0 rf1 = 91712., 91712. ifname = B, D rf2 = 92224., 92224. fe = '3mm', '3mm' syn(1) = 12.6 pol = RCP, LCP lo1 = 91200., 91200. syn(3) = 13.1 ! First IF = 13112. to 13624. / Name = v3mm_ii Station = VLBA Priority = 0 rf1 = 91812., 91812. ifname = B, D rf2 = 92324., 92324. fe = '3mm', '3mm' syn(1) = 13.9 pol = RCP, LCP lo1 = 91300., 91300. syn(3) = 12.9 ! First IF = 14412. to 14924. / Name = v3mm_jf Station = VLBA Priority = 0 rf1 = 92012., 92012. ifname = B, D rf2 = 92524., 92524. fe = '3mm', '3mm' syn(1) = 12.9 pol = RCP, LCP lo1 = 91500., 91500. syn(3) = 13.1 ! First IF = 13412. to 13924. / Name = v3mm_ij Station = VLBA Priority = 0 rf1 = 92312., 92312. ifname = B, D rf2 = 92824., 92824. fe = '3mm', '3mm' syn(1) = 14.4 pol = RCP, LCP lo1 = 91800., 91800. syn(3) = 12.9 ! First IF = 14912. to 15424. / Name = v3mm_ik Station = VLBA Priority = 0 rf1 = 92512., 92512. ifname = B, D rf2 = 93024., 93024. fe = '3mm', '3mm' syn(1) = 14.6 pol = RCP, LCP lo1 = 92000., 92000. syn(3) = 12.9 ! First IF = 15112. to 15624. / Name = v3mm_jg Station = VLBA Priority = 0 rf1 = 92512., 92512. ifname = B, D rf2 = 93024., 93024. fe = '3mm', '3mm' syn(1) = 13.4 pol = RCP, LCP lo1 = 92000., 92000. syn(3) = 13.1 ! First IF = 13912. to 14424. / Name = v3mm_jh Station = VLBA Priority = 0 rf1 = 92712., 92712. ifname = B, D rf2 = 93224., 93224. fe = '3mm', '3mm' syn(1) = 13.6 pol = RCP, LCP lo1 = 92200., 92200. syn(3) = 13.1 ! First IF = 14112. to 14624. / Name = v3mm_kc Station = VLBA Priority = 0 rf1 = 92812., 92812. ifname = B, D rf2 = 93324., 93324. fe = '3mm', '3mm' syn(1) = 11.9 pol = RCP, LCP lo1 = 92300., 92300. syn(3) = 13.4 ! First IF = 12412. to 12924. / Name = v3mm_ji Station = VLBA Priority = 0 rf1 = 93012., 93012. ifname = B, D rf2 = 93524., 93524. fe = '3mm', '3mm' syn(1) = 13.9 pol = RCP, LCP lo1 = 92500., 92500. syn(3) = 13.1 ! First IF = 14412. to 14924. / Name = v3mm_kd Station = VLBA Priority = 0 rf1 = 93312., 93312. ifname = B, D rf2 = 93824., 93824. fe = '3mm', '3mm' syn(1) = 12.4 pol = RCP, LCP lo1 = 92800., 92800. syn(3) = 13.4 ! First IF = 12912. to 13424. / Name = v3mm_ke Station = VLBA Priority = 0 rf1 = 93512., 93512. ifname = B, D rf2 = 94024., 94024. fe = '3mm', '3mm' syn(1) = 12.6 pol = RCP, LCP lo1 = 93000., 93000. syn(3) = 13.4 ! First IF = 13112. to 13624. / Name = v3mm_jj Station = VLBA Priority = 0 rf1 = 93512., 93512. ifname = B, D rf2 = 94024., 94024. fe = '3mm', '3mm' syn(1) = 14.4 pol = RCP, LCP lo1 = 93000., 93000. syn(3) = 13.1 ! First IF = 14912. to 15424. / Name = v3mm_jk Station = VLBA Priority = 0 rf1 = 93712., 93712. ifname = B, D rf2 = 94224., 94224. fe = '3mm', '3mm' syn(1) = 14.6 pol = RCP, LCP lo1 = 93200., 93200. syn(3) = 13.1 ! First IF = 15112. to 15624. / Name = v3mm_kf Station = VLBA Priority = 0 rf1 = 93812., 93812. ifname = B, D rf2 = 94324., 94324. fe = '3mm', '3mm' syn(1) = 12.9 pol = RCP, LCP lo1 = 93300., 93300. syn(3) = 13.4 ! First IF = 13412. to 13924. / Name = v3mm_lc Station = VLBA Priority = 0 rf1 = 94012., 94012. ifname = B, D rf2 = 94524., 94524. fe = '3mm', '3mm' syn(1) = 11.9 pol = RCP, LCP lo1 = 93500., 93500. syn(3) = 13.6 ! First IF = 12412. to 12924. / Name = v3mm_kg Station = VLBA Priority = 0 rf1 = 94312., 94312. ifname = B, D rf2 = 94824., 94824. fe = '3mm', '3mm' syn(1) = 13.4 pol = RCP, LCP lo1 = 93800., 93800. syn(3) = 13.4 ! First IF = 13912. to 14424. / Name = v3mm_kh Station = VLBA Priority = 0 rf1 = 94512., 94512. ifname = B, D rf2 = 95024., 95024. fe = '3mm', '3mm' syn(1) = 13.6 pol = RCP, LCP lo1 = 94000., 94000. syn(3) = 13.4 ! First IF = 14112. to 14624. / Name = v3mm_ld Station = VLBA Priority = 0 rf1 = 94512., 94512. ifname = B, D rf2 = 95024., 95024. fe = '3mm', '3mm' syn(1) = 12.4 pol = RCP, LCP lo1 = 94000., 94000. syn(3) = 13.6 ! First IF = 12912. to 13424. / Name = v3mm_le Station = VLBA Priority = 0 rf1 = 94712., 94712. ifname = B, D rf2 = 95224., 95224. fe = '3mm', '3mm' syn(1) = 12.6 pol = RCP, LCP lo1 = 94200., 94200. syn(3) = 13.6 ! First IF = 13112. to 13624. / Name = v3mm_ki Station = VLBA Priority = 0 rf1 = 94812., 94812. ifname = B, D rf2 = 95324., 95324. fe = '3mm', '3mm' syn(1) = 13.9 pol = RCP, LCP lo1 = 94300., 94300. syn(3) = 13.4 ! First IF = 14412. to 14924. / Name = v3mm_lf Station = VLBA Priority = 0 rf1 = 95012., 95012. ifname = B, D rf2 = 95524., 95524. fe = '3mm', '3mm' syn(1) = 12.9 pol = RCP, LCP lo1 = 94500., 94500. syn(3) = 13.6 ! First IF = 13412. to 13924. / Name = v3mm_kj Station = VLBA Priority = 0 rf1 = 95312., 95312. ifname = B, D rf2 = 95824., 95824. fe = '3mm', '3mm' syn(1) = 14.4 pol = RCP, LCP lo1 = 94800., 94800. syn(3) = 13.4 ! First IF = 14912. to 15424. / Name = v3mm_kk Station = VLBA Priority = 0 rf1 = 95512., 95512. ifname = B, D rf2 = 96024., 96024. fe = '3mm', '3mm' syn(1) = 14.6 pol = RCP, LCP lo1 = 95000., 95000. syn(3) = 13.4 ! First IF = 15112. to 15624. / Name = v3mm_lg Station = VLBA Priority = 0 rf1 = 95512., 95512. ifname = B, D rf2 = 96024., 96024. fe = '3mm', '3mm' syn(1) = 13.4 pol = RCP, LCP lo1 = 95000., 95000. syn(3) = 13.6 ! First IF = 13912. to 14424. / ! --------------- END OF VLBA SECTION ---------------------------- ! ! ===================================================================== ! Entries from freq_US.dat ! Just GBT entries: NRAO-140ft have been removed ! Revised, Jan 21, 2009 : GBT_S2 is obsolete: removed them. ! added: GBT_COLD for cold weather az motion restriction. ! added entries for prime focus 2 (910-1230 MHZ) ! Some additions to get same LOs as VLBA as needed by the RDBE. ! Later changed priority to use the original LOs by default, ! not the new RDBE ones. Force the RDBE user to set FIRSTLO. ! Aug. 15, 2011 Added the K band multi-beam receiver. RCW. ! Some date - changed to A, C for all but the new K band. RCW. ! ! *** This is a version set up for use with the RDBE. It is ! called freq_RDBE_GB.dat. ! For most bands, this is just using N*500+-100, or the corresponding ! restrictions for 2 LO systems. ! For cases where the VLBA and GBT use opposite sidebands, the ! GBT LO is set offset by 1024+512=1536 MHz from the corresponding ! VLBA LO. That way, the 512 MHz bands match. For the PFB ! personality, DiFX can invert sidebands so, if the RF frequencies ! match, they can be correlated. SCHED will be taught to ! recognize this. Oct 11, 2011 RCW ! ----------------------------------------------------------------- ! GBT based on web site on 8Dec2000 RCW. ! Revised 27Apr2002 FDG ! IF3 (=BBC) = LO1 - LO2 + LO3 - Fsky for X band and down. ! FIRSTLO ('lo1' in file below) = LO1 - LO2 + LO3; Fsky + 0.75GHz = lo1 ! IF3 (=BBC) = Fsky - LO1 - LO2 + LO3 at higher frequencies. ! FIRSTLO ('lo1' in file below) = LO1 + LO2 - LO3; Fsky - 0.75GHz = lo1 ! All GBT setups have LO3=10.5 GHz, IF3 = 0.75 GHz, and IF2 = 9.75 GHz. ! ! 90cm will still have 500 MHz added on the VLBA, not 512. ! So the full IF (mostly empty) corresponds to 12-524 MHz RF. ! The GBT then needs to be at 524+512=1036 MHz to get the ! same RF range. Name = gbt90cm Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 290, 290 ifname = A, C rf2 = 395, 395 fe = '90cm', '90cm' pol = RCP, LCP lo1 = 1036.0, 1036.0 note = 'LO1=1.348, LO2=10.812, LO3=10.5 ' / ! The VLBA can't do this so don't change to match IFs. Name = gbt70cm Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 385, 385 ifname = A, C rf2 = 520, 520 fe = '70cm', '70cm' pol = RCP, LCP lo1 = 1200.0, 1200.0 note = 'LO1=1.530, LO2=10.83, LO3=10.5 ' / ! I think setting the lo1 at 1536 will take care of having ! 512-1024 on the VLBA come out in 1024-512 in the GBT IF. Name = gbt50cm Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 512, 512 ifname = A, C rf2 = 690, 690 fe = '50cm', '50cm' pol = RCP, LCP lo1 = 1536.0, 1536.0 note = 'LO1=1.848, LO2=10.812, LO3=10.5 ' / ! The VLBA can't do this so don't change to match IFs. Name = gbt37cm Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 680, 680 ifname = A, C rf2 = 920, 920 fe = '37cm', '37cm' pol = RCP, LCP lo1 = 1550.0, 1550.0 note = 'LO1=1.880, LO2=10.83, LO3=10.5 ' / !---------------------------------------------------- ! Prime Focus 2 : 910 to 1230 MHz !---------------------------------------------------- ! This VLBA can't do this so don't bother trying to match IFs. Name = gbt28cm Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 910, 910 ifname = A, C rf2 = 1230, 1230 fe = '28cm', '28cm' pol = RCP, LCP lo1 = 1820.0, 1820.0 note = 'LO1=2.570, LO2=11.25, LO3=10.5 ' / !---------------------------------------------------- ! L-band: Range is 1.10 - 1.75 GHz ! Ghigo email of 04/19/2011 indicates 1.1-1.8 ! The entries below are both limited by this range. ! note there is an optional notch filter 1230-1340 MHz ! to cut out a nearby radar ! RF bandpass filters: 1.10-1.80 GHz, 1.10-1.45 GHz, ! 1.30-1.45 GHz, 1.60-1.75 GHz ! VLBA and GBT can use the same LOs, so just adjust for 512-1024 !---------------------------------------------------- Name = g20cm_1 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 1100, 1100 ifname = A, C rf2 = 1588, 1588 fe = '20cm', '20cm' pol = RCP, LCP lo1 = 2100.0, 2100.0 note = 'LO1=4.332, LO2=12.732, LO3=10.5 ' / Name = g20cm_2 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 1376, 1376 ifname = A, C rf2 = 1800, 1800 fe = '20cm', '20cm' pol = RCP, LCP lo1 = 2400.0, 2400.0 note = 'LO1=4.632, LO2=12.732, LO3=10.5 ' / !---------------------------------------------------- ! S-band: range is 1.68 - 2.65 GHz ! RF bandpass filters: 1.68-2.65 GHz, 2.10-2.40 GHz. ! Note: strong RFI from satellite at 2320-2345 MHz: ! A notch filter has been installed which cuts out 2320-2345 MHz. ! VLBA and GBT can use the same LOs, so just adjust for 512-1024 !---------------------------------------------------- Name = gbt16cm Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 1680, 1680 ifname = A, C rf2 = 2088, 2088 fe = '13cm', '13cm' pol = RCP, LCP lo1 = 2600.0, 2600.0 note = 'LO1=7.832, LO2=15.732, LO3=10.5 ' / Name = gbt13cm Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 1876, 1876 ifname = A, C rf2 = 2388, 2388 fe = '13cm', '13cm' pol = RCP, LCP lo1 = 2900.0, 2900.0 note = 'LO1=8.132, LO2=15.732, LO3=10.5 ' / Name = g13cm_2 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 2076, 2076 ifname = A, C rf2 = 2588, 2588 fe = '13cm', '13cm' pol = RCP, LCP lo1 = 3100.0, 3100.0 note = 'LO1=8.332, LO2=15.732, LO3=10.5 ' / !--------------------------------------------------------- ! C-band: range is 3.9-6.18 GHz ! RF bandpass filters: 3.90-5.90 GHz, 3.95-4.65 GHz ! 4.55-5.25 GHz, 5.15-5.85 GHz ! Note: C-band extends from 3.9 to 6.18 GHz; more setups could be added. !--------------------------------------------------------- ! New versions provided on Jan 25 2008 by Frank Ghigo in email. ! I did not put in this file until Jan 6, 2009 RCW Reconfirmed with ! Frank Ghigo at that time. ! Later they were adjusted for the RDBE. For example, for the second ! To match the 512-1024 IF band when the VLBA LO is at 3900, ! the GBT will need to be at 4924+512=5436 Name = gbt6cma Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 3912, 3912 ifname = A, C rf2 = 4424, 4424 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 4936.0, 4936.0 note = 'LO1=7.168, LO2=12.732, LO3=10.5 ' / Name = gbt6cmb Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 4412, 4412 ifname = A, C rf2 = 4924, 4924 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 5436.0, 5436.0 note = 'LO1=7.668, LO2=12.732, LO3=10.5 ' / Name = gbt6cmc Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 4612, 4612 ifname = A, C rf2 = 5124, 5124 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 5636.0, 5636.0 note = 'LO1=7.868, LO2=12.732, LO3=10.5 ' / ! Add a couple to use when the old standard frequecy of 4990 is ! being accessed using a high LO on the VLBA to match sidebands ! with the VLA, which requires net upper. The new VLBA receiver ! can do either sideband in this range. Name = gbt6cmc2 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 4576, 4576 ifname = A, C rf2 = 5088, 5088 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 5600.0, 5600.0 note = 'LO1=7.832, LO2=12.732, LO3=10.5 ' / Name = gbt6cmd2 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 4876, 4876 ifname = A, C rf2 = 5388, 5388 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 5900.0, 5900.0 note = 'LO1=8.150, LO2=12.750, LO3=10.5 ' / ! Worry about the rest trying to match the new VLBA receiver ! which will use a weird and wonderful set of sidebands. Name = gbt6cmd Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 5000, 5000 ifname = A, C rf2 = 5500, 5500 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 6000.0, 6000.0 note = 'LO1=8.250, LO2=12.75, LO3=10.5 ' / ! Performance will be degraded above 5850 Name = gbt6cme Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 5400, 5400 ifname = A, C rf2 = 5900, 5900 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 6400.0, 6400.0 note = 'LO1=8.650, LO2=12.75, LO3=10.5 ' / ! High range of C-band ! Performance will be degraded above 5850 Name = gbt6cmf Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 5750, 5750 ifname = A, C rf2 = 6180, 6180 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 6700.0, 6700.0 note = 'LO1=8.950, LO2=12.75, LO3=10.5 ' ! Frank: I have made 3 X band setups because 800 MHz ! is too wide for the 500 MHz VLBA backend IF. I have ! arbitrarily set the ranges to match the VLBA settings. ! That simplifies matters for anyone trying to maximize ! their instantaneous bandwidth. !--------------------------------------------------------- ! Note: X-band range is 7.9 - 11.6 GHz ! more setups could be added ! The VLBA can match first LOs at 9100 and 9400, but prefers ! upper sideband low in the range. If the VLBA is using ! upper sideband and the GBT lower, a match requires adding ! 36 MHz to the GBT frequencies. SCHED is reluctant to span ! crossover frequencies, which will be different between the ! choices, so that should drive it to select the right set. !--------------------------------------------------------- Name = gbt4cma Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 7912, 7912 ifname = A, C rf2 = 8424, 8424 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 8936.0, 8936.0 note = 'LO1=11.168, LO2=12.732, LO3=10.5 ' / Name = gbt4cmb Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 8076, 8076 ifname = A, C rf2 = 8588, 8588 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 9100.0, 9100.0 note = 'LO1=11.332, LO2=12.732, LO3=10.5 ' / Name = gbt4cmd Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 8112, 8112 ifname = A, C rf2 = 8624, 8624 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 9136.0, 9136.0 note = 'LO1=11.368, LO2=12.732, LO3=10.5 ' / Name = gbt4cmc Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 8376, 8376 ifname = A, C rf2 = 8888, 8888 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 9400.0, 9400.0 note = 'LO1=11.632, LO2=12.732, LO3=10.5 ' / Name = gbt4cme Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 8412, 8412 ifname = A, C rf2 = 8924, 8924 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 9436.0, 9436.0 note = 'LO1=11.668, LO2=12.732, LO3=10.5 ' / !--------------------------------------------------------- ! I have only included 2 setups at 2 cm, corresponding to ! the main ones used on the VLBA and using the VLBA names ! Many others could be added. ! Both observatories use upper sideband so only the rf range ! changes for the RDBE. !--------------------------------------------------------- ! Note: GBT 2 cm receiver range is 11.8-15.6 GHz !--------------------------------------------------------- Name = gbt2cm_a2 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 11912, 11912 ifname = A, C rf2 = 12424, 12424 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 11400.0, 11400.0 note = 'LO1=9.168, LO2=12.732, LO3=10.5 ' / Name = gbt2cm_d2 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 14912, 14912 ifname = A, C rf2 = 15424, 15424 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 14400.0, 14400.0 note = 'LO1=12.168, LO2=12.732, LO3=10.5 ' / ! Needed to match an option for EB_RDBE. Name = gbt2cm_d3 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 15112, 15112 ifname = A, C rf2 = 15624, 15624 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 14600, 14600 note = 'LO1=12.368, LO2=12.732, LO3=10.5 (?)' / !------------------------------------------------------------------------- ! For 1cm only give a few near the water line version ! for now, matching VLBA sets. Many more could be added. ! This sideband is opposite the VLBA so frequency shifts ! are needed. !------------------------------------------------------------------------- ! GBT with new 7-beam 18-26 GHz receiver (KFPA) ! for VLBI, we use just beam 1. From email by Frank Ghigo Aug 15, 2011. !------------------------------------------------------------------------- Name = gbt1cm_a1 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 21212, 21212 ifname = B, D rf2 = 21724, 21724 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 22236.0, 22236.0 note = 'LO1=28.368, LO2=16.532, LO3=10.5 ' / Name = gbt1cm_a1 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 21312, 21312 ifname = B, D rf2 = 21824, 21824 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 22336.0, 22336.0 note = 'LO1=28.368, LO2=16.532, LO3=10.5 ' / Name = gbt1cm_a2 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 21512, 21512 ifname = B, D rf2 = 22024, 22024 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 22536.0, 22536.0 note = 'LO1=28.568, LO2=16.532, LO3=10.5 ' / Name = gbt1cm_b2 Station = GBT_VLBA, GBT_COLD Priority = 0 rf1 = 21712, 21712 ifname = B, D rf2 = 22224, 22224 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 22736, 22736 note = 'LO1=28.768, LO2=16.532, LO3=10.5 ' / Name = gbt1cm_a3 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 21812, 21812 ifname = B, D rf2 = 22324, 22324 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 22836.0, 22836.0 note = 'LO1=28.868, LO2=16.532, LO3=10.5 ' / Name = gbt1cm_a4 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 22012, 22012 ifname = B, D rf2 = 22524, 22524 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 23036.0, 23036.0 note = 'LO1=28.868, LO2=16.532, LO3=10.5 ' / Name = gbt1cm_b3 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 23512, 23512 ifname = B, D rf2 = 24024, 24024 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 24536.0, 24536.0 note = 'LO1=30.568, LO2=16.532, LO3=10.5 ' / !------------------------------------------------------ ! 7mm SiO lines at 42519.3, 42820.54, and 43122.03 ! VLBA standard band at 43135 MHz. ! VLA band at 43289.90- 43339.90 ! These use the same sideband as the the VLBA so just ! change the RF ranges. !------------------------------------------------------ ! GBT 7 mm receiver frequency range is 40.0-48.0 GHz. !------------------------------------------------------ Name = gbt7mm_c7 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 42312, 42312 ifname = A, C rf2 = 42824, 42824 fe = '7mm', '7mm' pol = RCP, LCP lo1 = 41800.0, 41800.0 note = 'LO1=36.568, LO2=15.732, LO3=10.5 ' / Name = gbt7mm_b8 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 42712, 42712 ifname = A, C rf2 = 43224, 43224 fe = '7mm', '7mm' pol = RCP, LCP lo1 = 42200.0, 42200.0 note = 'LO1=36.968, LO2=15.732, LO3=10.5 ' / Name = gbt7mm_c8 Station = GBT_VLBA, GBT_COLD priority = 0 rf1 = 42912, 42912 ifname = A, C rf2 = 43424, 43424 fe = '7mm', '7mm' pol = RCP, LCP lo1 = 42400.0, 42400.0 note = 'LO1=37.168, LO2=15.732, LO3=10.5 ' / !------------------------------------------------------ ! Some example frequency setups for the GBT 3mm receiver, ! based on the standard freq.dat file !------------------------------------------------------ ! Adapted from email from Frank Ghigo on March 9, 2012. (RCW) ! ! The GBT receiver has 4 overlapping bands ! 68-74 GHz FL1 upper sideband; lo1 = sky frequency - 750 MHz ! 73-80 GHz FL2 lower sideband; lo1 = sky frequency + 750 MHz ! 79-86 GHz FL3 upper sideband; lo1 = sky frequency - 750 MHz ! 85-92 GHz FL4 upper sideband; lo1 = sky frequency - 750 MHz ! ! Beam 1 connects to DAR inputs A and C ! Beam 2 connects to DAR inputs B and D ! ! I am told the Tsys on beam 2 is slightly better, so ifname=B,D is used here. ! example in 68-74 GHz band: Name = gbt3mm_a0 Station = GBT_VLBA, GBT_COLD Priority = 0 rf1 = 70012., 70012. ifname = B, D rf2 = 70524., 70524. fe = '3mm', '3mm' pol = RCP, LCP lo1 = 69500., 69500. note = 'LO1A=66.0, LO2=14.0, LO3=10.5, filter2_8, upper sideband' / ! example in 73-80 GHz band: Name = gbt3mm_a1 Station = GBT_VLBA, GBT_COLD Priority = 0 rf1 = 74976., 75076. ifname = B, D rf2 = 75488., 75588. fe = '3mm', '3mm' pol = RCP, LCP lo1 = 76000., 76000. note = 'LO1A=66.0, LO1B=15.25, LO2=15.75, LO3=10.5, filter7_14, lower sideband' / ! examples in 79-86 band : Name = gbt3mm_be Station = GBT_VLBA, GBT_COLD Priority = 0 rf1 = 79712., 79712. ifname = B, D rf2 = 80224., 80224. fe = '3mm', '3mm' pol = RCP, LCP lo1 = 79200., 79200. note = 'LO1A=66.0, LO1B=8.8, LO2=14.9, LO3=10.5, filter13_20, upper sideband' / Name = gbt3mm_ai Station = GBT_VLBA, GBT_COLD Priority = 0 rf1 = 79812., 79812. ifname = B, D rf2 = 80324., 80324. fe = '3mm', '3mm' pol = RCP, LCP lo1 = 79300., 79300. note = 'LO1A=66.0, LO1B=8.8, LO2=15.0, LO3=10.5, filter13_20, upper sideband' / Name = gbt3mm_bf Station = GBT_VLBA, GBT_COLD Priority = 0 rf1 = 80012., 80012. ifname = B, D rf2 = 80524., 80524. fe = '3mm', '3mm' pol = RCP, LCP lo1 = 79500., 79500. note = 'LO1A=66.0, LO1B=8.8, LO2=15.2, LO3=10.5, filter13_20, upper sideband' / ! ! examples in 85-92 GHz: Name = gbt3mm_eh Station = GBT_VLBA, GBT_COLD Priority = 0 rf1 = 85512., 85512. ifname = B, D rf2 = 86024., 86024. fe = '3mm', '3mm' pol = RCP, LCP lo1 = 85000., 85000. note = 'LO1A=66.0, LO1B=13.75, LO2=15.75, LO3=10.5, filter19_26, upper sideband' / Name = gbt3mm_fe Station = GBT_VLBA, GBT_COLD Priority = 0 rf1 = 85712., 85712. ifname = B, D rf2 = 86224., 86224. fe = '3mm', '3mm' pol = RCP, LCP lo1 = 85200., 85200. note = 'LO1A=66.0, LO1B=13.95, LO2=15.75, LO3=10.5, filter19_26, upper sideband' / Name = gbt3mm_ei Station = GBT_VLBA, GBT_COLD Priority = 0 rf1 = 85812., 85812. ifname = B, D rf2 = 86324., 86324. fe = '3mm', '3mm' pol = RCP, LCP lo1 = 85300., 85300. note = 'LO1A=66.0, LO1B=14.05, LO2=15.75, LO3=10.5, filter19_26, upper sideband' / Name = gbt3mm_ff Station = GBT_VLBA, GBT_COLD Priority = 0 rf1 = 86012., 86012. ifname = B, D rf2 = 86524., 86524. fe = '3mm', '3mm' pol = RCP, LCP lo1 = 85500., 85500. note = 'LO1A=66.0, LO1B=14.25, LO2=15.75, LO3=10.5, filter19_26, upper sideband' / ! The following were added by Craig Walker to push high enough to cover ! the 86846.89 MHz SiO line. Note that the usual maser observed is at ! 86243.35 MHz so it is covered by the above set. ! Note that the final letters of the name indicate the VLBA setup that ! matches. Name = gbt3mm_ej Station = GBT_VLBA, GBT_COLD Priority = 0 rf1 = 86312., 86312. ifname = B, D rf2 = 86824., 86824. fe = '3mm', '3mm' pol = RCP, LCP lo1 = 85800., 85800. note = 'LO1A=66.0, LO1B=14.55, LO2=15.75, LO3=10.5, filter19_26, upper sideband' / Name = gbt3mm_ek Station = GBT_VLBA, GBT_COLD Priority = 0 rf1 = 86512., 86512. ifname = B, D rf2 = 87024., 87024. fe = '3mm', '3mm' pol = RCP, LCP lo1 = 86000., 86000. note = 'LO1A=66.0, LO1B=14.75, LO2=15.75, LO3=10.5, filter19_26, upper sideband' / ! ! ===================================================================== ! The following entries in the SCHED frequency catalog are for stations ! of the LBA and associates in the southern hemisphere. ! These stations are maintained in file freq_ATNF.dat. ! ===================================================================== Name = ho20cm Station = HOBART priority = 0 rf1 = 1320, 1320 ifname = '2N', '1N' rf2 = 1750, 1750 pol = RCP, LCP lo1 = 1800, 1800 note = 'Confirmed 11/06/2003 email from Brett Reid' ! lo1 is dummy value: lo is not controlled by VEX / Name = ho13cm Station = HOBART priority = 0 rf1 = 2200, 2200 ifname = '2N', '1N' rf2 = 2500, 2500 pol = RCP, LCP lo1 = 1500.0, 1500.0 / Name = ho6cm Station = HOBART priority = 0 rf1 = 4550, 4550 ifname = '2N', '1N' rf2 = 5050, 5050 pol = RCP, LCP lo1 = 4300.0, 4300.0 note = 'Confirmed 11/06/2003 email from Brett Reid' ! lo1 is dummy value: lo is not controlled by VEX / Name = ho5cm Station = HOBART priority = 0 rf1 = 6250, 6250 ifname = '2N', '1N' rf2 = 6950, 6950 pol = RCP, LCP lo1 = 4300.0, 4300.0 note = 'Confirmed 11/06/2003 email from Brett Reid' ! lo1 is dummy value: lo is not controlled by VEX / Name = ho3cm Station = HOBART, HOB_MK5 priority = 0 rf1 = 8150, 8150 ifname = '1N', '2N' rf2 = 8700, 8700 pol = RCP, LCP lo1 = 8080.0, 8080.0 note = 'Confirmed 11/06/2003 email from Brett Reid' ! lo1 is dummy value: lo is not controlled by VEX / Name = ho2cm Station = HOBART priority = 0 rf1 = 12150, 12150 ifname = '2N', '1N' rf2 = 12650, 12650 pol = RCP, LCP lo1 = 1000.0, 1000.0 note = 'Confirmed 11/06/2003 email from Brett Reid' ! lo1 is dummy value: lo is not controlled by VEX / Name = ho1cm Station = HOBART, HOB_MK5 priority = 0 rf1 = 16000, 16000 ifname = '2N', '1N' rf2 = 26000, 26000 pol = RCP, LCP lo1 = 19000.00, 19000.00 note = 'Confirmed 11/06/2003 email from Brett Reid' ! lo1 is dummy value: lo is not controlled by VEX / Name = ho1cm Station = HOB_MK5 priority = 5 rf1 = 22300, 22300 ifname = '2N', '1N' rf2 = 22700, 22700 altifn = '1A', '2A' pol = RCP, LCP lo1 = 22100.00, 22100.00 note = 'Dummy setup' / Name = hosx Station = HOBART, HOB_MK5 priority = 1 rf1 = 2190, 8180, 2190 ifname = '2N', '1N', '3N' rf2 = 2470, 8980, 2470 pol = RCP, RCP, RCP lo1 = 2020, 8080, 2020 note = 'Confirmed 11/06/2003 email from Brett Reid' ! lo1 is dummy value: lo is not controlled by VEX / Name = cd20cm Station = CEDUNA priority = 0 rf1 = 1320, 1320 ifname = '2N', '1N' rf2 = 1750, 1750 pol = RCP, LCP lo1 = 1800, 1800 note = 'Dummy entry for Tests' / Name = cd13cm Station = CEDUNA priority = 0 rf1 = 2200, 2200 ifname = '2N', '1N' rf2 = 2500, 2500 pol = RCP, LCP lo1 = 1500.0, 1500.0 ! updates June 2003 CJP by info from Simon Ellingsen / Name = cd6cm Station = CEDUNA priority = 0 rf1 = 4500, 4500 ifname = '2N', '1N' rf2 = 5000, 5000 pol = RCP, LCP lo1 = 4100.0, 4100.0 ! updates June 2003 CJP by info from Simon Ellingsen / Name = cd4cm Station = CEDUNA priority = 0 rf1 = 6200, 6200 ifname = '2N', '1N' rf2 = 6900, 6900 pol = RCP, LCP lo1 = 5000.0, 5000.0 ! updates June 2003 CJP by info from Simon Ellingsen / Name = cd3cm Station = CEDUNA priority = 0 rf1 = 8200, 8200 ifname = '2N', '1N' rf2 = 8800, 8800 pol = RCP, LCP lo1 = 7000.0, 7000.0 ! updates June 2003 CJP by info from Simon Ellingsen / Name = cd2cm Station = CEDUNA priority = 0 rf1 = 12000, 12000 ifname = '2N', '1N' rf2 = 12200, 12200 pol = RCP, LCP lo1 = 10000.0, 10000.0 ! updates June 2003 CJP by info from Simon Ellingsen / Name = cd1cm Station = CEDUNA priority = 0 rf1 = 21000, 21000 ifname = '2N', '1N' rf2 = 25200, 25200 pol = RCP, LCP lo1 = 20000.0, 20000.0 ! updates June 2003 CJP by info from Simon Ellingsen / Name = at20cm Station = ATCA priority = 0 rf1 = 1250, 1250 ifname = '2N', '1N' rf2 = 1780, 1780 pol = RCP, LCP lo1 = 700.0, 700.0 ! updated june 2003 Chris Phillips, ATCA observers guide ! lo1 is dummy value: lo is not controlled by VEX / Name = at13cm Station = ATCA priority = 0 rf1 = 2200, 2200 ifname = '2N', '1N' rf2 = 2500, 2500 pol = RCP, LCP lo1 = 2000.0, 2000.0 ! updated june 2003 Chris Phillips, ATCA observers guide ! lo1 is dummy value: lo is not controlled by VEX / Name = at6cm Station = ATCA priority = 0 rf1 = 4400, 4400 ifname = '2N', '1N' rf2 = 6700, 6700 pol = RCP, LCP lo1 = 4500.0, 4500.0 ! updated june 2003 Chris Phillips, ATCA observers guide ! lo1 is dummy value: lo is not controlled by VEX / Name = at3cm Station = ATCA priority = 0 rf1 = 8000, 8000 ifname = '2N', '1N' rf2 = 9200, 9200 pol = RCP, LCP lo1 = 7800.0, 7800.0 ! updated june 2003 Chris Phillips, ATCA observers guide ! lo1 is dummy value: lo is not controlled by VEX / Name = at1cm Station = ATCA priority = 5 rf1 = 16000, 16000 ifname = '2N', '1N' rf2 = 25200, 25200 pol = RCP, LCP lo1 = 19000.00, 19000.00 ! updated june 2003 Chris Phillips, ATCA observers guide ! lo1 is dummy value: lo is not controlled by VEX / Name = at7mm Station = ATCA priority = 5 rf1 = 30000, 30000 ifname = A, C rf2 = 45000, 45000 pol = RCP, LCP lo1 = 25000.00, 25000.00 ! lo1 is dummy value: lo is not controlled by VEX / Name = at3mm Station = ATCA priority = 5 rf1 = 86000, 86000 ifname = A, C rf2 = 105000, 105000 pol = RCP, LCP lo1 = 80000.00, 80000.00 ! lo1 is dummy value: lo is not controlled by VEX / Name = mp20cm Station = MOPRA priority = 0 rf1 = 1300, 1300 ifname = '2N', '1N' rf2 = 1800, 1800 pol = RCP, LCP lo1 = 1000.0, 1000.0 ! updated june 2003 from Mopra Technical Summary ! lo1 is dummy value: lo is not controlled by VEX / Name = mp13cm Station = MOPRA priority = 0 rf1 = 1800, 1800 ifname = '2N', '1N' rf2 = 3000, 3000 pol = RCP, LCP lo1 = 1600.0, 1600.0 ! updated june 2003 from Mopra Technical Summary ! lo1 is dummy value: lo is not controlled by VEX / Name = mp6cm Station = MOPRA priority = 0 rf1 = 4500, 4500 ifname = '2N', '1N' rf2 = 6700, 6700 pol = RCP, LCP lo1 = 4500.0, 4500.0 ! updated june 2003 from Mopra Technical Summary ! lo1 is dummy value: lo is not controlled by VEX / Name = mp3cm Station = MOPRA priority = 0 rf1 = 8000, 8000 ifname = '2N', '1N' rf2 = 9200, 9200 pol = RCP, LCP lo1 = 7800.0, 7800.0 ! updated june 2003 from Mopra Technical Summary ! lo1 is dummy value: lo is not controlled by VEX / Name = mp1cm Station = MOPRA priority = 0 rf1 = 20000, 20000 ifname = '2N', '1N' rf2 = 25200, 25200 pol = RCP, LCP lo1 = 19000.00, 19000.00 ! updated june 2003 from Mopra Technical Summary ! lo1 is dummy value: lo is not controlled by VEX / Name = mp3mm Station = MOPRA priority = 0 rf1 = 86000, 86000 ifname = A, C rf2 = 115000, 115000 pol = RCP, LCP lo1 = 80000.00, 80000.00 ! lo1 is dummy value: lo is not controlled by VEX / Name = mp7mm Station = MOPRA priority = 0 rf1 = 30000, 30000 ifname = A, C rf2 = 45000, 45000 pol = RCP, LCP lo1 = 25000.00, 25000.00 ! lo1 is dummy value: lo is not controlled by VEX / Name = pa20cm Station = PARKES priority = 0 rf1 = 1200, 1200 ifname = '2N', '1N' rf2 = 1800, 1800 pol = RCP, LCP lo1 = 1600.0, 1600.0 ! updated may 1999 with information from T Tzioumis. ! lo1 is dummy value: lo is not controlled by VEX ! http://www.parkes.atnf.csiro.au/documentation/user_guide/node4.html/ / Name = pa13cm Station = PARKES priority = 0 rf1 = 2200, 2200 ifname = '2N', '1N' rf2 = 2500, 2500 pol = RCP, LCP lo1 = 1600.0, 1600.0 ! updated may 1999 with information from T Tzioumis. ! lo1 is dummy value: lo is not controlled by VEX ! http://www.parkes.atnf.csiro.au/documentation/user_guide/node4.html / Name = pasx Station = PARKES, PARK_MK5 priority = 0 rf1 = 2200, 8100, 2200 ifname = '2N', '1N', '3N' rf2 = 2500, 8700, 2500 pol = RCP, RCP, RCP lo1 = 2020, 8100.0, 2020 ! lo1 is dummy value: lo is not controlled by VEX ! http://www.parkes.atnf.csiro.au/documentation/user_guide/node4.html / Name = pa6cm Station = PARKES priority = 0 rf1 = 4500, 4500 ifname = '2N', '1N' rf2 = 5100, 5100 pol = RCP, LCP lo1 = 4500.0, 4500.0 ! updated may 1999 with information from T Tzioumis. ! lo1 is dummy value: lo is not controlled by VEX ! http://www.parkes.atnf.csiro.au/documentation/user_guide/node4.html / Name = pa3cm Station = PARKES, PARK_MK5 priority = 1 rf1 = 8100, 8100 ifname = '2N', '1N' altifn = '1A', '2A' rf2 = 8700, 8700 pol = RCP, LCP lo1 = 8100.0, 8100.0 ! updated may 1999 with information from T Tzioumis. ! lo1 is dummy value: lo is not controlled by VEX ! http://www.parkes.atnf.csiro.au/documentation/user_guide/node4.html / Name = pa4cm Station = PARKES priority = 0 rf1 = 5900, 5900 ifname = '2N', '1N' rf2 = 6800, 6800 pol = RCP, LCP lo1 = 4500.0, 4500.0 ! updated june 2003 Chris Phillips ! lo1 is dummy value: lo is not controlled by VEX ! http://www.parkes.atnf.csiro.au/documentation/user_guide/node4.html / Name = pa2cm Station = PARKES priority = 0 rf1 = 12000, 12000 ifname = '2N', '1N' rf2 = 15000, 15000 pol = RCP, LCP lo1 = 10000.0, 10000.0 ! updated june 2003 Chris Phillips ! lo1 is dummy value: lo is not controlled by VEX ! http://www.parkes.atnf.csiro.au/documentation/user_guide/node4.html / Name = pa1cm Station = PARKES priority = 0 rf1 = 21000, 21000 ifname = '2N', '1N' rf2 = 25200, 25200 pol = RCP, LCP lo1 = 19000.00, 19000.00 ! updated may 1999 with information from T Tzioumis. ! lo1 is dummy value: lo is not controlled by VEX ! http://www.parkes.atnf.csiro.au/documentation/user_guide/node4.html / Name = ww20cm Station = WARK12M priority = 0 rf1 = 1200, 1200 ifname = 'A', 'B' rf2 = 1750, 1750 pol = RCP, LCP lo1 = 1000, 1000 note = 'Not actual values' / Name = ww13cm Station = WARK12M priority = 0 rf1 = 2200, 2200 ifname = 'C1', 'D2' rf2 = 2500, 2500 pol = RCP, LCP lo1 = 1900, 1900 note = 'From Stuart Weston, 2013/04/04' / Name = ww3cm Station = WARK12M priority = 1 rf1 = 8112, 8112 ifname = 'A1', 'B2' rf2 = 8624, 8624 altifn = 'B1', 'A2' pol = RCP, LCP lo1 = 7600, 7600 note = 'From Stuart Weston, 2013/04/04' / !Name = ww3cmr Station = WARK12M priority = 0 ! rf1 = 8112, 8112 ifname = 'A1', 'B1' ! rf2 = 8624, 8624 ! pol = RCP, RCP lo1 = 7600, 7600 ! note = 'From Stuart Weston, 2013/04/04' !/ Name = wwsx Station = WARK12M priority = 1 rf1 = 2200, 8100 ifname = 'C1', 'A1' rf2 = 2250, 8700 pol = RCP, RCP lo1 = 1900, 7600.0 ! lo1 is dummy value: lo is not controlled by VEX ! http://www.parkes.atnf.csiro.au/documentation/user_guide/node4.html / Name = ak20cm Station = ASKAP priority = 0 rf1 = 1130, 1130 ifname = '2N', '1N' rf2 = 1830, 1830 pol = RCP, LCP lo1 = 1000, 1000 note = 'Updated from CJP 20131121. Fake LO (is tunable)' / Name = ak3cm Station = ASKAP priority = 0 rf1 = 8000, 8000 ifname = '2N', '1N' rf2 = 9000, 9000 pol = RCP, LCP lo1 = 8000, 8000 note = 'Not actual values' / ! AuScope geodetic antennas Name = aus13cm station = katherin, yarragad, hobart12 priority = 1 rf1 = 1910, 1910 ifname = C2, B2 rf2 = 2412, 2412 altifn = D2, A4 pol = RCP, LCP lo1 = 1900, 1900 note = 'from Jim Lovell 2013' ! rf1, rf2 assume DBBC filter 2 / Name = aus3cm Station = KATHERIN, yarragad, hobart12 priority = 1 rf1 = 7610, 7610 ifname = A1, B1 rf2 = 8624, 8624 altifn = B4, A2 pol = RCP, LCP lo1 = 7600, 7600 note = 'From Jim Lovell 2013' ! rf1, rf2 assume DBBC filter 1 or 2 / Name = aussx Station = KATHERIN, yarragad, hobart12 priority = 2 rf1 = 8112, 8624, 1910 ifname = A1, B4, C2 rf2 = 8624, 9136, 2412 altifn = '', '', D2 pol = RCP, RCP, RCP lo1 = 7600, 7600, 1900 note = 'From Jim Lovell 2013' ! different rf1, rf2 come from different DBBC filters / ! ========================= Arecibo =============================== ! ================================================================== ! The following is the Freq.dat file for Arecibo LBW, S-Radar, C-band ! Tapasi Ghosh, 8 October 2001 ! ! Adding X-band and S-low and S-High today. TG, 26 April 2002 ! ! Adding 610 MHz and C-High, CJS, 15 May 2006 ! ! Also modifying LBW, S-Low, S-High, C-band and X-band to avoid the loss ! of correlation for i.f. frequencies below 600 MHz. Should be good for ! up to 2 GBps recording. Sideband swap for X-band Rx above 8.5 GHz ! taken into acocunt -- hopefully! CJS, 15 May 2006 ! ! Removing S2 July 22, 2010 RCW. ! ================================================================== ! !---------------- 327 MHz Rx ------------------------------ / Name = ar90cm Station = ARECIBO priority = 0 rf1 = 309, 309 ifname = A, C rf2 = 344, 344 fe = '90cm', '90cm' pol = RCP, LCP lo1 = 1076, 1076 note = 'Frontend 30-MHz filter (between 312-342 MHz), TG 22-Sep-04' / !---------------- 610 MHz Rx ------------------------------ / Name = ar50cm Station = ARECIBO priority = 0 rf1 = 605, 605 ifname = A, C rf2 = 615, 615 fe = '50cm', '50cm' pol = RCP, LCP lo1 = 1360, 1360 note = 'Frontend 4-MHz filter for 607.6-611.8 MHz (HPW), CS 15-May-06' / !---------------- LBW Rx ------------------------------ / Name = arlb5a Station = ARECIBO priority = 0 rf1 = 1110, 1110 ifname = A, C rf2 = 1400, 1400 fe = '205a', '205a' pol = RCP, LCP lo1 = 2005, 2005 note = 'RX=LBW, with lfbf=5, lower 300 MHz CS 15-May-06' / Name = arlbw2 Station = ARECIBO priority = 0 rf1 = 1120, 1120 ifname = A, C rf2 = 1220, 1220 fe = '20c2', '20c2' pol = RCP, LCP lo1 = 1920, 1920 note = 'RX=LBW, with lfbf=2, TG 07-Oct-01' / Name = arlbw8 Station = ARECIBO priority = 0 rf1 = 1180, 1180 ifname = A, C rf2 = 1280, 1280 fe = '20c8', '20c8' pol = RCP, LCP lo1 = 1980, 1980 note = 'RX=LBW, with lfbf=8, TG 07-Oct-01' / Name = arlbw3 Station = ARECIBO priority = 0 rf1 = 1230, 1230 ifname = A, C rf2 = 1470, 1470 fe = '20c3', '20c3' pol = RCP, LCP lo1 = 2100, 2100 note = 'RX=LBW, with lfbf=3, TG 07-Oct-01' / Name = arlb5b Station = ARECIBO priority = 0 rf1 = 1300, 1300 ifname = A, C rf2 = 1600, 1600 fe = '205b', '205b' pol = RCP, LCP lo1 = 2200, 2200 note = 'RX=LBW, with lfbf=5, middle 300 MHz CS 15-May-06' / Name = arlbw6 Station = ARECIBO priority = 0 rf1 = 1360, 1360 ifname = A, C rf2 = 1470, 1470 fe = '20c6', '20c6' pol = RCP, LCP lo1 = 2165, 2165 note = 'RX=LBW, with lfbf=6, TG 07-Oct-01' / Name = arlb5d Station = ARECIBO priority = 0 rf1 = 1390, 1390 ifname = A, C rf2 = 1690, 1690 fe = '205d', '205d' pol = RCP, LCP lo1 = 2290, 2290 note = 'RX=LBW, with lfbf=5, incl. HI+OH for z=0 CS 15-May-06' / Name = arlb5c Station = ARECIBO priority = 0 rf1 = 1500, 1500 ifname = A, C rf2 = 1800, 1800 fe = '205c', '205c' pol = RCP, LCP lo1 = 2400, 2400 note = 'RX=LBW, with lfbf=5, upper 300 MHz CS 15-May-06' / Name = arlbw4 Station = ARECIBO priority = 0 rf1 = 1550, 1550 ifname = A, C rf2 = 1820, 1820 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 2435, 2435 note = 'RX=LBW, with lfbf=4, TG 07-Oct-01' / !----------------- S-Radar Rx ------------------------------ Name = arsrdh Station = ARECIBO priority = 0 rf1 = 2330, 2330 ifname = C, A rf2 = 2430, 2430 fe = 'srd1', 'srd1' pol = RCP, LCP lo1 = 3130.0, 3130.0 note = 'Using S-radar Rx + High filter, RFI at 2400 MHz' / Name = arsrdl Station = ARECIBO priority = 0 rf1 = 2230, 2230 ifname = C, A rf2 = 2330, 2330 fe = 'srd2', 'srd2' pol = RCP, LCP lo1 = 3030.0, 3030.0 note = 'Using S-radar+low filter, Needs ~1hr to change from high' / !--- S-Low (1.8 - 3.1 GHz) Rx, native linear, use Zbox for circ --- / Name = arslo1 Station = ARECIBO priority = 0 rf1 = 1700, 1700 ifname = A, C rf2 = 2000, 2000 fe = 'slo1', 'slo1' pol = RCP, LCP lo1 = 2600, 2600 note = 'S-low, with sbwfb=1, strong RFI around 1.9 and 2.4 GHz' / Name = arslo2 Station = ARECIBO priority = 0 rf1 = 1900, 1900 ifname = A, C rf2 = 2200, 2200 fe = 'slo2', 'slo2' pol = RCP, LCP lo1 = 2800, 2800 note = 'S-low, with sbwfb=2 or 4, strong RFI around 1.9 and 2.4 GHz' / Name = arslo3 Station = ARECIBO priority = 0 rf1 = 2100, 2100 ifname = A, C rf2 = 2400, 2400 fe = 'slo3', 'slo3' pol = RCP, LCP lo1 = 3000, 3000 note = 'S-low, with sbwfb=2, strong RFI around 1.9 and 2.4 GHz' / Name = arslo4 Station = ARECIBO priority = 0 rf1 = 2300, 2300 ifname = A, C rf2 = 2600, 2600 fe = 'slo4', 'slo4' pol = RCP, LCP lo1 = 3200, 3200 note = 'S-low, with sbwfb=4, strong RFI around 1.9 and 2.4 GHz' / Name = arslo5 Station = ARECIBO priority = 0 rf1 = 2600, 2600 ifname = A, C rf2 = 2900, 2900 fe = 'slo5', 'slo5' pol = RCP, LCP lo1 = 3500, 3500 note = 'S-low, with sbwfb=3' / Name = arslo6 Station = ARECIBO priority = 0 rf1 = 2800, 2800 ifname = A, C rf2 = 3100, 3100 fe = 'slo1', 'slo1' pol = RCP, LCP lo1 = 2600, 2600 note = 'S-low, with sbwfb=3' / !---------------- S-High (3-4 GHz) Rx ------------------------------ / Name = arshi1 Station = ARECIBO priority = 0 rf1 = 3000, 3000 ifname = A, C rf2 = 3300, 3300 fe = 'shi1', 'shi1' pol = RCP, LCP lo1 = 3900, 3900 note = 'S-hi, no RF filters, native linear, use Zeeman box' / Name = arshi2 Station = ARECIBO priority = 0 rf1 = 3200, 3200 ifname = A, C rf2 = 3500, 3500 fe = 'shi2', 'shi2' pol = RCP, LCP lo1 = 4100, 4100 note = 'S-hi, no RF filters, native linear, use Zeeman box' / Name = arshi3 Station = ARECIBO priority = 0 rf1 = 3400, 3400 ifname = A, C rf2 = 3700, 3700 fe = 'shi3', 'shi3' pol = RCP, LCP lo1 = 4300, 4300 note = 'S-hi, no RF filters, native linear, use Zeeman box' / Name = arshi4 Station = ARECIBO priority = 0 rf1 = 3600, 3600 ifname = A, C rf2 = 3900, 3900 fe = 'shi1', 'shi1' pol = RCP, LCP lo1 = 4500, 4500 note = 'S-hi, no RF filters, native linear, use Zeeman box' / Name = arshi5 Station = ARECIBO priority = 0 rf1 = 3800, 3800 ifname = A, C rf2 = 4100, 4100 fe = 'shi5', 'shi5' pol = RCP, LCP lo1 = 4700, 4700 note = 'S-hi, no RF filters, native linear, use Zeeman box' / !-----C-band (3.85 - 6 GHz) Rx, native linear, use the Zbox ---- / Name = arcb0 Station = ARECIBO priority = 0 rf1 = 4050, 4050 ifname = A, C rf2 = 4350, 4350 fe = '6cm0', '6cm0' pol = RCP, LCP lo1 = 4950.0, 4950.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcb1 Station = ARECIBO priority = 0 rf1 = 4250, 4250 ifname = A, C rf2 = 4550, 4550 fe = '6cm1', '6cm1' pol = RCP, LCP lo1 = 5150.0, 5150.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcb2 Station = ARECIBO priority = 0 rf1 = 4450, 4450 ifname = A, C rf2 = 4750, 4750 fe = '6cm2', '6cm2' pol = RCP, LCP lo1 = 5350.0, 5350.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcb3 Station = ARECIBO priority = 0 rf1 = 4650, 4650 ifname = A, C rf2 = 4950, 4950 fe = '6cm3', '6cm3' pol = RCP, LCP lo1 = 5550.0, 5550.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcb4 Station = ARECIBO priority = 0 rf1 = 4850, 4850 ifname = A, C rf2 = 5150, 5150 fe = '6cm4', '6cm4' pol = RCP, LCP lo1 = 5750.0, 5750.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcb5 Station = ARECIBO priority = 0 rf1 = 5050, 5050 ifname = A, C rf2 = 5350, 5350 fe = '6cm5', '6cm5' pol = RCP, LCP lo1 = 5950.0, 5950.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcb6 Station = ARECIBO priority = 0 rf1 = 5250, 5250 ifname = A, C rf2 = 5550, 5550 fe = '6cm6', '6cm6' pol = RCP, LCP lo1 = 6150.0, 6150.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcb7 Station = ARECIBO priority = 0 rf1 = 5450, 5450 ifname = A, C rf2 = 5750, 5750 fe = '6cm7', '6cm7' pol = RCP, LCP lo1 = 6350.0, 6350.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcb8 Station = ARECIBO priority = 0 rf1 = 5650, 5650 ifname = A, C rf2 = 5950, 5950 fe = '6cm8', '6cm8' pol = RCP, LCP lo1 = 6550.0, 6550.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcb9 Station = ARECIBO priority = 0 rf1 = 5850, 5850 ifname = A, C rf2 = 6150, 6150 fe = '6cm9', '6cm9' pol = RCP, LCP lo1 = 6750.0, 6750.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / !----- CBHigh (6-8 GHz) Rx, native linear, use the Z Box --- / Name = arcbh0 Station = ARECIBO priority = 0 rf1 = 5900, 5900 ifname = A, C rf2 = 6200, 6200 fe = 'cbh0', 'cbh0' pol = RCP, LCP lo1 = 6800.0, 6800.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcbh1 Station = ARECIBO priority = 0 rf1 = 6100, 6100 ifname = A, C rf2 = 6400, 6400 fe = 'cbh1', 'cbh1' pol = RCP, LCP lo1 = 7000.0, 7000.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcbh2 Station = ARECIBO priority = 0 rf1 = 6300, 6300 ifname = A, C rf2 = 6600, 6600 fe = 'cbh2', 'cbh2' pol = RCP, LCP lo1 = 7200.0, 7200.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcbh3 Station = ARECIBO priority = 0 rf1 = 6500, 6500 ifname = A, C rf2 = 6800, 6800 fe = 'cbh3', 'cbh3' pol = RCP, LCP lo1 = 7400.0, 7400.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcbh4 Station = ARECIBO priority = 0 rf1 = 6700, 6700 ifname = A, C rf2 = 7000, 7000 fe = 'cbh4', 'cbh4' pol = RCP, LCP lo1 = 7600.0, 7600.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcbh5 Station = ARECIBO priority = 0 rf1 = 6900, 6900 ifname = A, C rf2 = 7200, 7200 fe = 'cbh5', 'cbh5' pol = RCP, LCP lo1 = 7800.0, 7800.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcbh6 Station = ARECIBO priority = 0 rf1 = 7100, 7100 ifname = A, C rf2 = 7400, 7400 fe = 'cbh6', 'cbh6' pol = RCP, LCP lo1 = 8000.0, 8000.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcbh7 Station = ARECIBO priority = 0 rf1 = 7300, 7300 ifname = A, C rf2 = 7600, 7600 fe = 'cbh7', 'cbh7' pol = RCP, LCP lo1 = 8200.0, 8200.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcbh8 Station = ARECIBO priority = 0 rf1 = 7500, 7500 ifname = A, C rf2 = 7800, 7800 fe = 'cbh8', 'cbh8' pol = RCP, LCP lo1 = 8400.0, 8400.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / Name = arcbh9 Station = ARECIBO priority = 0 rf1 = 7700, 7700 ifname = A, C rf2 = 8000, 8000 fe = 'cbh9', 'cbh9' pol = RCP, LCP lo1 = 8600.0, 8600.0 note = 'Using up-down conversion unit + VLBIinp at 1.5 MHz' / !----- X-band (8-10 GHz) Rx, native linear, use the Z Box --- / Name = arxbh0 Station = ARECIBO priority = 0 rf1 = 7850, 7850 ifname = A, C rf2 = 8150, 8150 fe = 'xbh0', 'xbh0' pol = RCP, LCP lo1 = 8750, 8750 note = 'No rf filters yet, RFI at ~ 9.3 and 9.7 GHz' / Name = arxbh1 Station = ARECIBO priority = 0 rf1 = 8050, 8050 ifname = A, C rf2 = 8350, 8350 fe = 'xbh1', 'xbh1' pol = RCP, LCP lo1 = 8950, 8950 note = 'No rf filters yet, RFI at ~ 9.3 and 9.7 GHz' / Name = arxbh2 Station = ARECIBO priority = 0 rf1 = 8250, 8250 ifname = A, C rf2 = 8550, 8550 fe = 'xbh2', 'xbh2' pol = RCP, LCP lo1 = 9150, 9150 note = 'No rf filters yet, RFI at ~ 9.3 and 9.7 GHz' / ! This one added to match the VLBA at 9100 first LO for ! RDBE tests. Name = arxbha2 Station = ARECIBO priority = 1 rf1 = 8200, 8200 ifname = A, C rf2 = 8500, 8500 fe = 'xbh2', 'xbh2' pol = RCP, LCP lo1 = 9100, 9100 note = 'Match VLBA. No rf filters yet, RFI at ~ 9.3 and 9.7 GHz' / Name = arxbh3 Station = ARECIBO priority = 0 rf1 = 8450, 8450 ifname = A, C rf2 = 8750, 8750 fe = 'xbh3', 'xbh3' pol = RCP, LCP lo1 = 7850, 7850 note = 'No rf filters yet, RFI at ~ 9.3 and 9.7 GHz' / Name = arxbh4 Station = ARECIBO priority = 0 rf1 = 8650, 8650 ifname = A, C rf2 = 8950, 8950 fe = 'xbh4', 'xbh4' pol = RCP, LCP lo1 = 8050, 8050 note = 'No rf filters yet, RFI at ~ 9.3 and 9.7 GHz' / Name = arxbh5 Station = ARECIBO priority = 0 rf1 = 8850, 8850 ifname = A, C rf2 = 9150, 9150 fe = 'xbh5', 'xbh5' pol = RCP, LCP lo1 = 8250, 8250 note = 'No rf filters yet, RFI at ~ 9.3 and 9.7 GHz' / Name = arxbh6 Station = ARECIBO priority = 0 rf1 = 9050, 9050 ifname = A, C rf2 = 9350, 9350 fe = 'xbh6', 'xbh6' pol = RCP, LCP lo1 = 8450, 8450 note = 'No rf filters yet, RFI at ~ 9.3 and 9.7 GHz' / Name = arxbh7 Station = ARECIBO priority = 0 rf1 = 9250, 9250 ifname = A, C rf2 = 9550, 9550 fe = 'xbh7', 'xbh7' pol = RCP, LCP lo1 = 8650, 8650 note = 'No rf filters yet, RFI at ~ 9.3 and 9.7 GHz' / Name = arxbh8 Station = ARECIBO priority = 0 rf1 = 9450, 9450 ifname = A, C rf2 = 9750, 9750 fe = 'xbh8', 'xbh8' pol = RCP, LCP lo1 = 8850, 8850 note = 'No rf filters yet, RFI at ~ 9.3 and 9.7 GHz' / Name = arxbh9 Station = ARECIBO priority = 0 rf1 = 9650, 9650 ifname = A, C rf2 = 9950, 9950 fe = 'xbh9', 'xbh9' pol = RCP, LCP lo1 = 9050, 9050 note = 'No rf filters yet, RFI at ~ 9.3 and 9.7 GHz' / Name = arxbha Station = ARECIBO priority = 0 rf1 = 9850, 9850 ifname = A, C rf2 = 10150, 10150 fe = 'xbha', 'xbha' pol = RCP, LCP lo1 = 9250, 9250 note = 'No rf filters yet, RFI at ~ 9.3 and 9.7 GHz' / ! ! ! ! ===================================================================== ! The following entries in the SCHED frequency catalog are for EVN ! stations. ! These stations are maintained in file freq_EVN.dat which is maintained ! by C. Reynolds (up tp 2007), A.Polatidis (JIVE), Friso Olnon ! (since sep 2009) and Des Small (since nov 2010). ! ===================================================================== ! Any changes directly to freq.dat will be lost at the next update. ! ! 211097: changes requested by Phil Edwards VSOG, upd priorities ! 170997: changed to freq_EVN.dat ! 210897: Changed on_sx to ON60; inserted Cm frequencies ! 130897: inserted various X band setups Wb,Mc,Nt,On ! 310798: L-band filter VLBA_EB ! 231198: 5cm OH+Methanol/6cm OH setups collected by Desmurs (JFD) ! 231198: changes to LO shanghai ! 260199: 21cm and 7mm setups collected by Desmurs (JFD) ! 220699: Update Hart, small change to eb ! 151099: inserted UHF findings from Desmurs ! 270100: fixed an error in K band CM ! 070200: red-shifted OH and HI Eh7/Ek10 (Hagiwara/Kloeckner) (TrEf/EfOn/WbJb) ! 280300: entires for Sh (dual pol) and Ur ! ----------------------------------------------------------------- ! 301100: responsibility for maintenance of freq_EVN.dat passed to Cormac ! Reynolds (CR). ! 301100: update Hh, Mh, Mc, Tr, Cm, Sh ! 300101: update Mc again ! 020201: update 5cm/OH entries from CJP email (Eb, Nt) ! 160501: update ON 6cm freq range from Conway email ! 030701: ON sx setup ! 050701: Ef/Eb x and sx setup ! 090701: Sh sx setup: added second X-band IF ! 021001: Mh and Eb 3mm setup removed - now maintained in freq_mm.dat by J. ! Attridge at Haystack. ! 171001: 5 and 6 cm OH setups added for several stations after email from JFD ! Mh ifnames at 22 GHz also changed. ! 291001: new 21cm setups for CM/JB ! 180102: 5 cm setups for ON ! 100602: Ef S/X setup - IF1 and IF2 swapped. ! 020702: Added dummy dual pol setups at single pol stations. ! 100902: Changed On 21cm LO. ! 210103: Added multiple 21cm LOs for Onsala. ! 250903: Lovell at 6cm ! 070104: Corrected cm18cm ! 040812: Update to Ur 6cm, 30cm ! 040813: sorted all entries on (lowest) lo freq. ! 040826: update Jb,Eb,Tr ! 050927: new shanghai 18cm LO. JB1_VLBA had wrong IF names at 90cm. ! 051115: added back 3mm setups for Mh, On, Ef/Eb and new PdB and PV ! 051122: Shanghai updates (email from An Tao) ! 051123: Urumqi updates (email from Liu Xiang) ! 060126: Onsala dummy dual pol, Nt 5cm, ! 060518: New Shanghai S/X receiver ! 061012: Removed 43GHz entries for Mc (email from A. Orlati) ! 061102: Put back Nt X-band dummy dual-pol ! 061128: Changed Nt X-band dummy dual-pol to have RCP in the correct IF. ! 070221: Added Hh at 1cm. ! 070525: Changed On at 6cm to avoid high patch at 1Gbps ! 070618: mc_s had the wrong 'fe' - fixed ! 070903: fixed LO and rf1, rf2 for mc5cm ! 080901: Added eb_1420_hi setup - used in HSA 21cm example - from D.Graham/C.Walker ! 080908: New Nt 5cm entries from Cassaro's email ! 080920: Dummy dual pol X band entry OK for Nt ! 081120: Extended frequency range and LO for Wb 6cm to suppress 1Gb/s error messages ! 081120: Extended frequency range for Ef 6cm to suppress 1Gb/s error messages ! 081120: Extended frequency range for On 6cm to suppress 1Gb/s error messages ! 081120: Extended frequency range for Jb1 6cm to suppress 1Gb/s error messages ! 081120: Extended frequency range for Jb2 6cm to suppress 1Gb/s error messages ! 081121: Added "high" 1cm entries for JB2, Cm, On, Ys, Hh, Mc ! 081121: Refined YS 1cm entry ! 081121: Refined Ur X band entries - single pol RCP and dummy dual X band ! 081121: Refined Ys X and S/X band entries - S to IFB deVicente email 081015 ! 081212: Added entries for MERLIN outstations (Da, Ta, Kn, De) to the Cm setups ! 090219: Added Yebes 5cm entries. RCW based on AP email of today. ! 090400: Modified Yebes 5cm and added 6cm ! 090511: Added Kunming ! 090706: Added Beijing (Miyun50 to be?) ! 090924: Added Robledo 34m ! 090924: Renamed Beijing to Miyun50 ! 100318: Fix LOs for sx at EB. RCW. ! 110209: Update Ys values, based on Pablo de Vicente's email. DMS ! 120323: Added KVZR stations with R1002 digital backends. DMS ! 120710: Updated Hh K-band LO. DMS ! 131115: Updated Ef and Eb from Uwe Bach's catalogs. ! 131204: Fix "ifname" (was "name") and missing "fe" on several lines. RCW ! 131209: Add altif for EFLSBERG where needed for examples. May get ! replaced by EVN version. RCW. ! 140210: Changed Hart 26m setups for the new DBBC. IF names changed, but ! frequency ranges not. CR ! ! ------------------------------------------------------------------------- ! KVAZAR stations. ! Added by small@jive.nl 2012-03-23 ! Name = kvzr_l Station=BADARY,SVETLOE,ZELENCHK priority=0 rf1 = 1380, 1380 ifname = A, B rf2 = 1720, 1720 fe = '18cm' pol = RCP, LCP lo1 = 1260.0, 1260.0 note = 'passed by Alexey Melnikov, Mar2014' / Name = kvzr_s Station=BADARY,SVETLOE,ZELENCHK priority=0 rf1 = 2150, 2150 ifname = A, B rf2 = 2500, 2500 fe = '13cm' pol = RCP, LCP lo1 = 2020.0, 2020.0 note = 'passed by Alexey Melnikov, Mar2014' / Name = kvzr_c Station=BADARY,SVETLOE,ZELENCHK priority=0 rf1 = 4600, 4600 ifname = A, B rf2 = 5500, 5500 fe = '6cm' pol = RCP, LCP lo1 = 4500.0, 4500.0 note = 'Added by Des Small, 24 February 2012' / Name = kvzr_x Station=BADARY,SVETLOE,ZELENCHK priority=0 rf1 = 8180, 8180 ifname = A, B rf2 = 9080, 9080 fe = '4cm' pol = RCP, LCP lo1 = 8080.0, 8080.0 note = 'Added by Des Small, 24 February 2012' / Name = kvzr_k Station=BADARY,SVETLOE,ZELENCHK priority=0 rf1 = 22020, 22020 ifname = A, B rf2 = 22920, 22920 fe = '1cm' pol = RCP, LCP lo1 = 21920.0, 21920.0 note = 'Added by Des Small, 24 February 2012' / ! ----------------------------------------------------------------------- ! Effelsberg ! ! From Dave Graham EMAIL of 15 Nov 1996. ! There are some cases of multiple receivers. Think about ! how to deal with them. ! 2013nov12 Update of Ef and Eb frequency ranges. Uwe Bach ! ! ----------------------------------------------------------------------- ! ! EB_RDBE ! Name = eb_610 Station = EB_RDBE priority = 0 rf1 = 607, 607 ifname = A, C rf2 = 650, 650 fe = '50cm', '50cm' pol = RCP, LCP lo1 = 0, 0 note = 'Prime focus system: not usually available (new in 2011).' / Name = eb_1330 Station = EB_RDBE priority = 0 rf1 = 1280, 1280 ifname = B, D rf2 = 1400, 1400 fe = '20cm', '20cm' pol = RCP, LCP lo1 = 780, 780 note = 'Prime focus receiver, new 2008 (lower edge)' / Name = eb_1360 Station = EB_RDBE priority = 0 rf1 = 1290, 1290 ifname = B, D rf2 = 1430, 1430 fe = '20cm', '20cm' pol = RCP, LCP lo1 = 810, 810 note = 'Prime focus receiver, new 2008 (centre)' / Name = eb_1390 Station = EB_RDBE priority = 0 rf1 = 1320, 1320 ifname = B, D rf2 = 1450, 1450 fe = '20cm', '20cm' pol = RCP, LCP lo1 = 840, 840 note = 'Prime focus receiver, new 2008 (upper edge)' / Name = eb_1620 Station = EB_RDBE priority = 0 rf1 = 1560, 1560 ifname = B, D rf2 = 1690, 1690 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 1090, 1090 note = 'Prime focus receiver, new 2008 (lower)' / Name = eb_1640 Station = EB_RDBE priority = 0 rf1 = 1590, 1590 ifname = B, D rf2 = 1730, 1730 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 1090, 1090 note = 'Prime focus receiver, new 2008 (centre)' / Name = eb_1660 Station = EB_RDBE priority = 0 rf1 = 1610, 1610 ifname = B, D rf2 = 1735, 1735 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 1110, 1110 note = 'Prime focus receiver, new 2008 (upper)' / Name = eb_s Station = EB_RDBE priority = 1 rf1 = 2200, 2200 ifname = B, D rf2 = 2320, 2320 fe = '13cm', '13cm' pol = RCP, RCP lo1 = 1700, 1700 note = '170Jy S-band system for use with SX, RCP only.' / Name = eb_sd Station = EB_RDBE priority = 5 rf1 = 2200, 2200 ifname = B, D rf2 = 2320, 2320 fe = '13cm', '13cm' pol = RCP, LCP lo1 = 1700, 1700 note = 'Dummy dual-pol entry, only RCP available (CR 2Jul02).' / Name = eb_2695 Station = EB_RDBE priority = 0 rf1 = 2645, 2645 ifname = B, D rf2 = 2745, 2745 fe = '13cm', '13cm' pol = RCP, LCP lo1 = 2000, 2000 note = '30Jy S-Band, not for use with X' / Name = eb_6cm Station = EB_RDBE priority = 0 rf1 = 4612, 4612 ifname = A, C rf2 = 5124, 5124 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 4100, 4100 note = '6cm secondary focus.' / Name = eb_6150 Station = EB_RDBE priority = 4 rf1 = 5912, 5912 ifname = A, C rf2 = 6424, 6424 fe = '5cm', '5cm' pol = RCP, LCP lo1 = 5400, 5400 note = 'rebuild in 2011' / Name = eb_6650 Station = EB_RDBE priority = 4 rf1 = 6412, 6412 ifname = A, C rf2 = 6924, 6924 fe = '5cm', '5cm' pol = RCP, LCP lo1 = 5900, 5900 note = 'rebuild in 2011' / Name = eb_sx Station = EB_RDBE priority = 2 rf1 = 2200, 2200, 8300, 8300 ifname = B, D, A, C rf2 = 2320, 2320, 8800, 8800 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, RCP, RCP, LCP lo1 = 1700, 1700, 7800, 7800 note = 'SX using 4cm secondary focus: not easy to get below 8300.' / Name = eb_x Station = EB_RDBE priority = 0 rf1 = 8312, 8312 ifname = A, C rf2 = 8824, 8824 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7800, 7800 note = '4cm secondary focus.' / Name = eb_xa Station = EB_RDBE priority = 1 rf1 = 7912, 7912 ifname = A, C rf2 = 8424, 8424 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7400, 7400 note = '4cm secondary focus. Tunable in 1 MHz steps' / Name = eb_xb Station = EB_RDBE priority = 1 rf1 = 8112, 8112 ifname = A, C rf2 = 8624, 8624 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7600, 7600 note = '4cm secondary focus. Tunable in 1 MHz steps' / Name = eb_xc Station = EB_RDBE priority = 1 rf1 = 8412, 8412 ifname = A, C rf2 = 8924, 8924 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7900, 7900 note = '4cm secondary focus. Tunable in 1 MHz steps' / Name = eb_xd Station = EB_RDBE priority = 2 rf1 = 8512, 8512 ifname = A, C rf2 = 9024, 9024 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 8100, 8100 note = '4cm secondary focus. Tunable in 1 MHz steps' / Name = eb2cm_p Station = EB_RDBE priority = 0 rf1 = 11700, 11700 ifname = B, D rf2 = 12500, 12500 fe = '2cm', '2cm' pol = LCP, LCP lo1 = 11500, 11500 note = '12GHz prime focus: not usually available:LCP only' / Name = eb2cm_a Station = EB_RDBE priority = 1 rf1 = 13712, 13712 ifname = A, C rf2 = 14224, 14224 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 13200, 13200 note = '2cm secondary focus' / Name = eb2cm_b Station = EB_RDBE priority = 1 rf1 = 14212, 14212 ifname = A, C rf2 = 14724, 14724 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 13700, 13700 note = '2cm secondary focus' / Name = eb2cm_c Station = EB_RDBE priority = 0 rf1 = 14712, 14712 ifname = A, C rf2 = 15224, 15224 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 14200, 14200 note = '2cm secondary focus' / Name = eb2cm_d Station = EB_RDBE priority = 0 rf1 = 15112, 15112 ifname = A, C rf2 = 15624, 15624 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 14600, 14600 note = '2cm secondary focus' / ! 1.3cm secondary focus Name = eb1cm_a Station = EB_RDBE priority = 1 rf1 = 21512, 21512 ifname = A, C rf2 = 21824, 21824 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 20800, 20800 note = '1.3cm secondary focus. Tunable in 1 MHz steps' / Name = eb1cm_b Station = EB_RDBE priority = 1 rf1 = 21712, 21712 ifname = A, C rf2 = 22224, 22224 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 21200, 21200 note = '1.3cm secondary focus. Tunable in 1 MHz steps' / Name = eb1cm_c Station = EB_RDBE priority = 1 rf1 = 21812, 21812 ifname = A, C rf2 = 22324, 22324 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 21300, 21300 note = '1.3cm secondary focus. Tunable in 1 MHz steps' / Name = eb1cm_d Station = EB_RDBE priority = 0 rf1 = 22012, 22012 ifname = A, C rf2 = 22524, 22524 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 21500, 21500 note = '1.3cm secondary focus. Tunable in 1 MHz steps' / Name = eb1cm_e Station = EB_RDBE priority = 1 rf1 = 22512, 22512 ifname = A, C rf2 = 23024, 23024 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 22000, 22000 note = '1.3cm secondary focus. Tunable in 1 MHz steps' / Name = eb1cm_f Station = EB_RDBE priority = 1 rf1 = 23012, 23012 ifname = A, C rf2 = 23524, 23524 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 22500, 22500 note = '1.3cm secondary focus. Tunable in 1 MHz steps' / Name = eb1cm_g Station = EB_RDBE priority = 1 rf1 = 23512, 23512 ifname = A, C rf2 = 24024, 24024 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 23000, 23000 note = '1.3cm secondary focus. Tunable in 1 MHz steps' / Name = eb1cm_h Station = EB_RDBE priority = 1 rf1 = 24012, 24012 ifname = A, C rf2 = 24424, 24424 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 23500, 23500 note = '1.3cm secondary focus. Tunable in 1 MHz steps' / Name = eb7mm Station = EB_RDBE priority = 1 rf1 = 42882, 42882 ifname = A, C rf2 = 43394, 43394 fe = '7mm', '7mm' pol = RCP, LCP lo1 = 43870, 43870 note = '7mm secondary focus: only LSB, no USB available' / Name = 3mm_EB_RDBE Station = EB_RDBE Priority = 0 rf1 = 86012, 86012 ifname = A, C rf2 = 86524, 86524 fe = '3mm', '3mm' pol = RCP, LCP lo1 = 85500, 85500 note = 'new 3mm RX: April 2001 for CMVA' / ! This section gives a selection of possible frequency setups for ! the Effelsberg DBBC (station code EFLSBERG) ! ! ! 2013nov06 Update for Ef frequency ranges. Uwe Bach ! ! ----------------------------------------------------------------------- ! ! EFLSBERG Name = ef92cm Station = EFLSBERG priority = 0 rf1 = 290, 290 ifname = A2, B4 rf2 = 370, 370 fe = '92cm', '92cm' pol = RCP, LCP lo1 = 177, 177 note = 'Prime focus system: not usually available (new in 2011).' / Name = ef50cm Station = EFLSBERG priority = 0 rf1 = 595, 595 ifname = A2, B4 rf2 = 626, 626 fe = '50cm', '50cm' pol = RCP, LCP lo1 = 460, 460 note = 'Prime focus system: not usually available (new in 2011).' / Name = ef30cm.EV8B Station = EFLSBERG priority = 4 rf1 = 785.5 , 785.5 ifname = A2, B4 rf2 = 793.5 , 793.5 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 640.5 , 640.5 note = 'RCV shifted LO1 (thus BBsyn) because HI line in upper part of 8 MHz' ! Obs freq 791.5 MHz ! BBC range 145-155MHz / Name = ef30cm.EM34 Station = EFLSBERG priority = 4 rf1 = 846.8 , 846.8 ifname = A2, B4 rf2 = 854.8 , 854.8 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 699.8 , 699.8 note = 'email from D.Graham (JFD 23-08-99) to cover 147-155 MHz in IF' ! Obs freq 848.8 MHz ! BBC range 145-155MHz / Name = ef30cm.EP30 Station = EFLSBERG priority = 4 rf1 = 848.49, 848.49 ifname = A2, B4 rf2 = 856.49, 856.49 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 701.49, 701.49 note = 'email from D.Graham (JFD 23-08-99) to cover 147-155 MHz in IF' ! Obs freq 850.49 MHz ! BBC range 145-155MHz / Name = ef30cm.E4C Station = EFLSBERG priority = 4 rf1 = 874.7 , 874.7 ifname = A2, B4 rf2 = 882.7 , 882.7 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 727.7 , 727.7 note = 'email from D.Graham (JFD 23-08-99) to cover 147-155 MHz in IF' ! Obs freq 876.7 MHz ! BBC range 145-155MHz / Name = ef30cm.EV8A Station = EFLSBERG priority = 4 rf1 = 882.6 , 882.6 ifname = A2, B4 rf2 = 890.6 , 890.6 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 737.6 , 737.6 note = 'RCV shifted LO1 (thus BBsyn) because HI line in upper part of 8 MHz' ! Obs freq 888.6 MHz ! BBC range 145-155MHz / Name = ef30cm.EB15B Station = EFLSBERG priority = 4 rf1 = 986.7 , 986.7 ifname = A2, B4 rf2 = 990.7 , 990.7 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 838.7 , 838.7 note = 'RCV shifted LO1 (thus BBsyn) because only 4 MHz needed' ! Obs freq 988.7 MHz ! BBC range 145-155MHz / Name = ef30cm.EB15A Station = EFLSBERG priority = 4 rf1 = 986.7 , 986.7 ifname = A2, B4 rf2 = 994.7 , 994.7 fe = '30cm' , '30cm' pol = RCP , LCP lo1 =839.7 , 839.7 note = 'email from D.Graham (JFD 23-08-99) to cover 147-155 MHz in IF' ! Obs freq 988.7 MHz ! BBC range 145-155MHz / Name = ef30cm.EO4B Station = EFLSBERG priority = 4 rf1 = 1033.2 , 1033.2 ifname = A2, B4 rf2 = 1041.2 , 1041.2 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 886.2 , 886.2 note = 'email from D.Graham (JFD 23-08-99) to cover 147-155 MHz in IF' ! Obs freq 1035.2 MHz ! BBC range 145-155MHz / Name = ef30cm.EO4A Station = EFLSBERG priority = 4 rf1 = 1046.6 , 1046.6 ifname = A2, B4 rf2 = 1054.6 , 1054.6 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 899.6 , 899.6 note = 'email from D.Graham (JFD 23-08-99) to cover 147-155 MHz in IF' ! Obs freq 1048.6 MHz ! BBC range 145-155MHz / Name = ef30cm.EP31A Station = EFLSBERG priority = 4 rf1 = 1068.75 , 1068.75 ifname = A2, B4 rf2 = 1076.75 , 1076.75 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 923.75 , 923.75 note = 'RCV shifted LO1 (thus BBsyn) because HI line in upper part of 8 MHz' ! Obs freq 1074.75 MHz ! BBC range 145-155MHz / Name = ef30cm.VAH1 Station = EFLSBERG priority = 4 rf1 = 1123.2 , 1123.2 ifname = A2, B4 rf2 = 1131.2 , 1131.2 fe = '30cm' , '30cm' pol = RCP , LCP lo1 =976.2 , 976.2 note = 'email from D.Graham (JFD 23-08-99) to cover 147-155 MHz in IF' ! Obs freq 1125.2 MHz ! BBC range 145-155MHz / Name = ef30cm.EP31B Station = EFLSBERG priority = 4 rf1 = 1163.25 , 1163.25 ifname = A2, B4 rf2 = 1171.25 , 1171.25 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 1016.25 , 1016.25 note = 'email from D.Graham (JFD 23-08-99) to cover 147-155 MHz in IF' ! Obs freq 1165.25 MHz ! BBC range 145-155MHz / Name = ef1340 Station = EFLSBERG priority = 5 rf1 = 1270, 1270 ifname = A2, B4 rf2 = 1310, 1410 fe = '20cm', '20cm' pol = RCP, LCP lo1 = 1190.0, 1190.0 note = '21cm prime focus receiver, lower edge at 1270 MHz' / Name = ef1380 Station = EFLSBERG priority = 4 rf1 = 1310, 1310 ifname = A2, B4 rf2 = 1450, 1450 fe = '20cm', '20cm' pol = RCP, LCP lo1 = 1230.0, 1230.0 note = '21cm prime focus receiver' / Name = ef1400 Station = EFLSBERG priority = 4 rf1 = 1330, 1330 ifname = A2, B4 rf2 = 1450, 1450 fe = '20cm', '20cm' pol = RCP, LCP lo1 = 1250.0, 1250.0 note = '21cm prime focus receiver, upper edge at 1450 MHz' / Name = ef21cm Station = EFLSBERG priority = 5 rf1 = 1370, 1370 ifname = A2, B4 rf2 = 1450, 1450 fe = '20cm', '20cm' pol = RCP, LCP lo1 = 1290.0, 1290.0 note = '21cm prime focus receiver, upper edge at 1450 MHz' / Name = ef1620 Station = EFLSBERG priority = 5 rf1 = 1550, 1550 ifname = A2, B4 rf2 = 1690, 1690 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 1470.0, 1470.0 note = '18cm prime focus receiver. Entry for red-shifted OH' / Name = ef1640 Station = EFLSBERG priority = 5 rf1 = 1570, 1570 ifname = A2, B4 rf2 = 1710, 1710 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 1490, 1490 note = '18cm Prime focus receiver, low LO' / Name = ef18cm Station = EFLSBERG priority = 4 rf1 = 1590, 1590 ifname = A2, B4 rf2 = 1730, 1730 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 1510.0, 1510.0 note = '18cm Prime focus receiver, standard LO' / Name = efsx Station = EFLSBERG priority = 5 rf1 = 8360, 2200 ifname = A2, B4 rf2 = 8460, 2300 fe = '13cm', '4cm' pol = RCP, RCP lo1 = 8260.0, 2100.0 note = 'Guessing from Pc-sched' ! ranges guessed assuming 100 - 200 BBC range in low output ! updated ifname and altifn after email from A. Kraus (CR 5Jun01) ! Swapped lo1 values March 18, 2010 RCW. / Name = efgeosx Station = EFLSBERG priority = 5 rf1 = 8210, 2200 ifname = A2, B4 rf2 = 8600, 2300 fe = '13cm', '4cm' pol = RCP, RCP lo1 = 8110.0, 2100.0 note = 'special setup for Geodesy, contact friend of VLBI' ! ranges guessed assuming 100 - 500 BBC ! Added after email from A. Kraus (CR 5Jun01) ! Swapped lo1 values March 18, 2010 RCW. / Name = ef6cm Station = EFLSBERG priority = 0 rf1 = 4600, 4600 ifname = A1, B3 rf2 = 5100, 5100 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 4100.0, 4100.0 note = '6cm secondary focus receiver. This LO covers the whole band.' / Name = ef5cm1 Station = EFLSBERG priority = 5 rf1 = 5900, 5900 ifname = A1, B3 rf2 = 6400, 6400 fe = '5cm', '5cm' pol = RCP, LCP lo1 = 5400.0, 5400.0 note = '5cm prime focus receiver. 500-1000 MHz IF.' / Name = ef5cm2 Station = EFLSBERG priority = 5 rf1 = 6100, 6100 ifname = A1, B3 rf2 = 6600, 6600 fe = '5cm', '5cm' pol = RCP, LCP lo1 = 5600.0, 5600.0 note = '5cm prime focus receiver. 500-1000 MHz IF.' / Name = ef5cm3 Station = EFLSBERG priority = 4 rf1 = 6400, 6400 ifname = A1, B3 rf2 = 6900, 6900 fe = '5cm', '5cm' pol = RCP, LCP lo1 = 5900.0, 5900.0 note = '5cm prime focus receiver. 500-1000 MHz IF.' / Name = ef_x Station = EFLSBERG priority = 0 rf1 = 8200, 8200 ifname = A1, B3 rf2 = 8700, 8700 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7700.0, 7700.0 note = '4cm secondary focus receiver. 500-1000 MHz IF.' / Name = ef_xa Station = EFLSBERG priority = 1 rf1 = 7900, 7900 ifname = A1, B3 rf2 = 8400, 8400 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7400, 7400 note = '4cm secondary focus receiver. 500-1000 MHz IF.' / Name = ef_xb Station = EFLSBERG priority = 1 rf1 = 8100, 8100 ifname = A1, B3 rf2 = 8600, 8600 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7600, 7600 note = '4cm secondary focus receiver. 500-1000 MHz IF.' / Name = ef_xc Station = EFLSBERG priority = 1 rf1 = 8300, 8300 ifname = A1, B3 rf2 = 8800, 8800 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7800, 7800 note = '4cm secondary focus receiver. 500-1000 MHz IF.' / Name = ef_xd Station = EFLSBERG priority = 1 rf1 = 8400, 8400 ifname = A1, B3 rf2 = 8900, 8900 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7900, 7900 note = '4cm secondary focus receiver. 500-1000 MHz IF.' / Name = ef_xe Station = EFLSBERG priority = 2 rf1 = 8600, 8600 ifname = A1, B3 rf2 = 9000, 9000 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 8100, 8100 note = '4cm secondary focus receiver. 500-1000 MHz IF, bamd edge at 9.0 GHz.' / Name = ef2cm_p Station = EFLSBERG priority = 0 rf1 = 11700, 11700 ifname = A2, B4 rf2 = 12500, 12500 fe = '2cm', '2cm' pol = LCP, LCP lo1 = 11500, 11500 note = '12GHz prime focus: not usually available:LCP' / Name = ef2cm_a Station = EFLSBERG priority = 1 rf1 = 13700, 13700 ifname = A1, B3 rf2 = 14200, 14200 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 13200, 13200 note = '2cm secondary focus. 500-1000 MHz IF.' / Name = ef2cm_b Station = EFLSBERG priority = 1 rf1 = 14200, 14200 ifname = A1, B3 rf2 = 14700, 14700 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 13700, 13700 note = '2cm secondary focus. 500-1000 MHz IF.' / Name = ef2cm_c Station = EFLSBERG priority = 0 rf1 = 14700, 14700 ifname = A1, B3 rf2 = 15200, 15200 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 14200, 14200 note = '2cm secondary focus. 500-1000 MHz IF.' / Name = ef2cm_d Station = EFLSBERG priority = 0 rf1 = 15100, 15100 ifname = A1, B3 rf2 = 15600, 15600 fe = '2cm', '2cm' pol = RCP, LCP lo1 = 14600, 14600 note = '2cm secondary focus. 500-1000 MHz IF.' / ! Original ifname = A1, B3 Name = ef1cm_a Station = EFLSBERG priority = 1 rf1 = 21500, 21500 ifname = A1, B3 altifn = B1, A3 rf2 = 21800, 21800 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 20800, 20800 note = '1.3cm secondary focus, IF 500-1000 MHz' / Name = ef1cm_b Station = EFLSBERG priority = 1 rf1 = 21700, 21700 ifname = A1, B3 altifn = B1, A3 rf2 = 22200, 22200 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 21200, 21200 note = '1.3cm secondary focus, IF 500-1000 MHz' / Name = ef1cm_c Station = EFLSBERG priority = 1 rf1 = 21800, 21800 ifname = A1, B3 altifn = B1, A3 rf2 = 22300, 22300 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 21300, 21300 note = '1.3cm secondary focus, IF 500-1000 MHz' / Name = ef1cm_d Station = EFLSBERG priority = 0 rf1 = 22000, 22000 ifname = A1, B3 altifn = B1, A3 rf2 = 22500, 22500 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 21500, 21500 note = '1.3cm secondary focus, IF 500-1000 MHz' / Name = ef1cm_e Station = EFLSBERG priority = 1 rf1 = 22500, 22500 ifname = A1, B3 altifn = B1, A3 rf2 = 23000, 23000 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 22000, 22000 note = '1.3cm secondary focus, IF 500-1000 MHz' / Name = ef1cm_f Station = EFLSBERG priority = 1 rf1 = 23000, 23000 ifname = A1, B3 altifn = B1, A3 rf2 = 23500, 23500 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 22500, 22500 note = '1.3cm secondary focus, IF 500-1000 MHz' / Name = ef1cm_g Station = EFLSBERG priority = 0 rf1 = 23500, 23500 ifname = A1, B3 altifn = B1, A3 rf2 = 24000, 24000 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 23000, 23000 note = '1.3cm secondary focus, IF 500-1000 MHz' / Name = ef1cm_h Station = EFLSBERG priority = 1 rf1 = 24000, 24000 ifname = A1, B3 altifn = B1, A3 rf2 = 24400, 24400 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 23500, 23500 note = '1.3cm secondary focus, IF 500-1000 MHz' / Name = ef7mm Station = EFLSBERG priority = 1 rf1 = 42870, 42870 ifname = A1, B3 rf2 = 43370, 43370 fe = '7mm', '7mm' pol = RCP, LCP lo1 = 43870, 43870 note = '7mm secondary focus: only LSB, no USB available' / Name = 3mm_eflsbg Station = EFLSBERG Priority = 0 rf1 = 86100, 86100 ifname = A1, B3 rf2 = 86400, 86400 fe = '3mm', '3mm' pol = LCP, RCP lo1 = 85500, 85500 note = 'new 3mm RX: April 2001 for CMVA' / ! ! EVN data by Huib Jan van Langevelde ! LO's from various e-mails, ifnames based on recorder ! rf1 and rf2 are usually simple guesses from BBC range. ! ! First EVN stations with VLBA -type recorders ! ! ! Add entries for all MERLIN outstations similar to Cambridge 32M ! since they share the VLBA DAR Name = cm21cm Station = CAMBG32M, DARNHALL, KNOCKIN, TABLEY, DEFFORD priority = 4 rf1 = 1400, 1400 ifname = C, A rf2 = 1430, 1430 fe = '21cm', '21cm' pol = RCP, LCP lo1 = 830.0, 830.0 note = 'From Burgess via email (CR 29Oct01)' / Name = cm18cm Station = CAMBG32M, DARNHALL, KNOCKIN, TABLEY, DEFFORD priority = 4 rf1 = 1610, 1610 ifname = C, A rf2 = 1730, 1730 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 1110.0, 1110.0 note = 'Confirmed by Alastair Gunn 31 Jan 2005' / Name = cm6cmOH Station = CAMBG32M, DARNHALL, KNOCKIN, TABLEY, DEFFORD priority = 5 rf1 = 4640, 4640 ifname = C, A rf2 = 5100, 5100 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 4140.0, 4140.0 note = 'MK2 LO setting-400MHz, P. Burgess (JFD 05Oct01)' ! update from JFD (CR 17Oct01) / Name = cm6cm Station = CAMBG32M, DARNHALL, KNOCKIN, TABLEY, DEFFORD priority = 4 rf1 = 4940, 4940 ifname = C, A rf2 = 5400, 5400 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 4440.0, 4440.0 note = 'Confirmed by Alastair Gunn 210897' / Name = cm5cmOH Station = CAMBG32M, DARNHALL, KNOCKIN, TABLEY, DEFFORD priority = 4 rf1 = 6000, 6000 ifname = C, A rf2 = 6100, 6100 fe = '5cm', '5cm' pol = RCP, LCP lo1 = 5512, 5512 note = 'MK2 LO setting-400MHz, P. Burgess (JFD 15Oct01)' ! ranges guessed assuming 100 - 200 BBC range ! update from JFD (CR 17Oct01) / Name = cm5cm Station = CAMBG32M, DARNHALL, KNOCKIN, TABLEY, DEFFORD priority = 4 rf1 = 6600, 6600 ifname = C, A rf2 = 6700, 6700 fe = '5cm', '5cm' pol = RCP, LCP lo1 = 6120, 6120 note = 'MK2 LO setting-400MHz, P. Burgess (JFD 15Oct01)' ! update from Burgess (CR 24Oct01) / Name = cm1cm Station = CAMBG32M, DARNHALL, KNOCKIN, TABLEY, DEFFORD priority = 4 rf1 = 22200,22200 ifname = C, A rf2 = 22600,22600 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 21680.0, 21680.0 note = 'Confirmed by Alastair Gunn 210897 CHECK' / Name = cm1cmhigh Station = CAMBG32M, DARNHALL, KNOCKIN, TABLEY, DEFFORD priority = 4 rf1 = 23500,23500 ifname = C, A rf2 = 23900,23900 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 23000.0, 23000.0 note = 'for high K-band test, ranges guessed' / Name = mh18cm Station = METSAHOV priority = 5 note = 'No 18cm at MH' / Name = mh6cm Station = METSAHOV priority = 5 note = 'No 6cm at MH' / Name = mh_sx Station = METSAHOV priority = 5 rf1 = 2210, 8150 ifname = C, A rf2 = 2350, 8630 fe = '13cm', '4cm' pol = RCP, RCP lo1 = 1530, 7650 note = 'From Mujunen 25/11/2005' / Name = mh1cm Station = METSAHOV priority = 4 rf1 = 21980, 21980 ifname = C, A rf2 = 22480, 22480 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 21480.0, 21480.0 note = 'LO based on Wiik 03JUN96' ! RCP & LCP, BBC range ~500-1000MHz (CR: from Kononen 1Dec00) ! CR: ifname C, A instead of B, A (from Huib 17Oct01, confirmed Kononen) / Name = mh7mm_sio Station = METSAHOV priority = 4 rf1 = 42980, 42980 ifname = C, A rf2 = 43480, 43480 fe = '7mm', '7mm' pol = LCP, LCP lo1 = 42480.0, 42480.0 note = ' ** LCP only **, Values from E-mail K.Karlamaa (JFD 19jan99) ' ! only single Pol LCP, BBC range ~500-1000MHz ! ifname updated from Kononen (CR 2Dec00) / ! METSAHOV at 3 mm for 256-16-1 dual pol ! Name = 3mm_metsa Station = METSAHOV Priority = 0 rf1 = 85872, 85872 ifname = A, C rf2 = 86372, 86372 fe = '3mm', '3mm' ! pol = LCP, RCP lo1 = 85372, 85372 pol = LCP, RCP lo1 = 85501, 85501 / ! Name = nt90cm Station = NOTO, NOTO_S2 priority = 3 Name = nt90cm Station = NOTO priority = 3 rf1 = 250, 250 ifname = C, A rf2 = 600, 600 fe = '90cm', '90cm' pol = RCP, LCP lo1 = 1150.1, 1150.1 note = '' ! awaiting confirmation from Cassaro (CR 21 Sep 2004) / !Name = nt50cm Station = NOTO, NOTO_S2 priority = 3 Name = nt50cm Station = NOTO priority = 3 rf1 = 600, 600 ifname = C, A rf2 = 950, 950 fe = '50cm', '50cm' pol = RCP, LCP lo1 = 0, 0 note = '' ! from Cassaro email 040820 (CR 21 Sep 2004) / ! Name = nt18cm Station = NOTO, NOTO_S2 priority = 3 Name = nt18cm Station = NOTO priority = 3 rf1 = 1622, 1622 ifname = C, A rf2 = 1702, 1702 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 799.1, 799.1 note = 'LO from Trigilio 26Sep96' ! email update Cassaro April 2003 (CR 1May03) / ! Name = nt18+21cm Station = NOTO, NOTO_S2 priority = 4 Name = nt18+21cm Station = NOTO priority = 4 rf1 = 1400, 1400 ifname = C, A rf2 = 1702, 1702 fe = '18+21cm', '18+21cm' pol = RCP, LCP lo1 = 799.1, 799.1 note = 'LO from Trigilio 26Sep96' ! email update Cassaro April 2003 (CR 1May03) / Name = ntsx Station = NOTO priority = 5 rf1 = 2040, 2040, 8100, 8100 ifname = C, D, A, B rf2 = 2540, 2540, 8600, 8600 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, RCP, RCP, RCP lo1 = 1540.1, 1540.1, 7600.1, 7600.1 note = 'From e-mail Corrado Trigilio 29/07/97, only RCP' ! ranges from assuming BBC can do 500 - 1000 MHz / ! Name = nt6cm Station = NOTO, NOTO_S2 priority = 3 Name = nt6cm Station = NOTO priority = 3 rf1 = 4700, 4700 ifname = C, A rf2 = 5100, 5100 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 4120.1, 4120.1 note = 'LO from Gino Tuccari 04JUN96; channels from Trigilio 27SEP96' ! ranges guessed assuming a 500 - 1000 MHz BBC / !Name = nt5cmOH Station = NOTO, NOTO_S2 priority = 5 ! rf1 = 6000, 6000 ifname = C, A ! rf2 = 6100, 6100 fe = '5cm', '5cm' ! pol = RCP, LCP lo1 = 5280.1, 5280.1 ! note = 'Setup not yet confirmed - may not work at all (CR 25Jan06)' ! ! added after email from C.Phillips (CR 2Feb01) ! ! removed after email from Cassaro - frequencies not available (CR 1May03) ! AGP: removed again after email from Cassaro 08Sep2008 !/ !Name = nt5cm Station = NOTO, NOTO_S2 priority = 5 ! rf1 = 6600, 6600 ifname = C, A ! rf2 = 6800, 6800 fe = '5cm', '5cm' ! pol = RCP, LCP lo1 = 7435.9, 7435.9 ! note = 'LSB receiver - LO by C. Trigilio Mar03' ! ! email update from Cassaro (CR 1May03) ! AGP: Removed and commented out after email from Cassaro 08Sep2008 ! Replaced by nt5cmA below !/ ! ! AGP: All Nt 5cm setups from email by Cassaro 08Sep2008 Name = nt5cmA Station = NOTO priority = 5 rf1 = 6500, 6500 ifname = C, A rf2 = 6800, 6800 fe = '5cm', '5cm' pol = RCP, LCP lo1 = 7435.9, 7435.9 note = 'LSB receiver - LO by P.Cassaro sep08' / Name = nt5cmB Station = NOTO priority = 5 rf1 = 6200, 6200 ifname = C, A rf2 = 6500, 6500 fe = '5cm', '5cm' pol = RCP, LCP lo1 = 7135.9, 7135.9 note = 'LSB receiver - LO by P.Cassaro sep08' / Name = nt5cmC Station = NOTO priority = 5 rf1 = 5900, 5900 ifname = C, A rf2 = 6200, 6200 fe = '5cm', '5cm' pol = RCP, LCP lo1 = 6835.9, 6835.9 note = 'LSB receiver - LO by P.Cassaro sep08' / Name = nt5cmD Station = NOTO priority = 5 rf1 = 5600, 5600 ifname = C, A rf2 = 5900, 5900 fe = '5cm', '5cm' pol = RCP, LCP lo1 = 6535.9, 6535.9 note = 'LSB receiver - LO by P.Cassaro sep08' / Name = nt5cmE Station = NOTO priority = 5 rf1 = 5300, 5300 ifname = C, A rf2 = 5600, 5600 fe = '5cm', '5cm' pol = RCP, LCP lo1 = 6235.9, 6235.9 note = 'LSB receiver - LO by P.Cassaro sep08' / !Name = nt_x Station = NOTO priority = 4 ! rf1 = 8100, 8100 ifname = C, A ! rf2 = 8600, 8600 fe = '4cm', '4cm' ! pol = RCP, RCP lo1 = 7600.1, 7600.1 ! note = 'Based on e-mail Corrado Trigilio 29/07/97' ! ! ranges from assuming BBC can do 500 - 1000 MHz ! ! removed after email from Cassaro (CR 1May03) !/ Name = nt_xd Station = NOTO priority = 6 rf1 = 8100, 8100 ifname = A, C rf2 = 8600, 8600 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7600.1, 7600.1 note = 'Dummy dual-pol entry, only RCP available (CR 28Nov06).' ! Worked Oct 2008 N08X1 and GW019B (AGP 20Oct08) ! ranges from assuming BBC can do 500 - 1000 MHz / Name = nt1cm Station = NOTO priority = 4 rf1 = 21950, 21950 ifname = C, A rf2 = 22325, 22325 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 21389.1, 21389.1 note = 'LO from Gino Tuccari 04JUN96; channels from Tuccari Mar03' ! ranges guessed assuming a 500 - 1000 MHz BBC ! email update Cassaro April 2003 (CR 1May03) ! removed NOTO_S2 email from Cassaro 08Sep2008 / Name = nt7mm_sio Station = NOTO priority = 4 rf1 = 42500 ifname = 'C' fe = '7mm' rf2 = 43250 pol = LCP lo1 = 42270.0 note = ' ** LCP only **, (JFD 05jan99); LO from Trigilio Mar03' ! only single Pol LCP, the receiver is shared with Medicina ! email update Cassaro April 2003 (CR 1May03) / ! removed at request of H. Xinyong (CR 3Sep03) !Name = sh18cmo Station = SHANGHAI, SHANG_S2 priority = 5 ! rf1 = 1320, 1320 ifname = A ! rf2 = 1820, 1820 fe = '18cm', '18cm' ! pol = LCP, LCP lo1 = 820.10, 820.10 ! note = 'Huang Xinyong 231198, old (obsolete?) configuration' ! ! ranges from assuming BBC can do 500 - 1000 MHz !/ ! Name = sh18cm Station = SHANGHAI, SHANG_S2 priority = 4 Name = sh18cm Station = SHANGHAI priority = 4 rf1 = 1600, 1600 ifname = C, A rf2 = 1740, 1740 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 2300.00, 2300.00 note = 'Huang Xinyong 27Sept05' / ! Name = sh6cm Station = SHANGHAI, SHANG_S2 priority = 5 Name = sh6cm Station = SHANGHAI priority = 5 rf1 = 4650, 4650 ifname = C, A rf2 = 5150, 5150 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 4200.0, 4200.0 note = 'Update freq. range AnTao 22Mar08' / Name = sh5cm Station = SHANGHAI, SHANG_S2 priority = 5 rf1 = 6400,6400 ifname = C, A rf2 = 6825,6825 fe = '5cm', '5cm' pol = RCP, LCP lo1 = 5900.0, 5900.0 note = 'Email from Shen Zhiqiang, 30 Jan 2010' / ! Name = shsx Station = SHANGHAI, SHANG_S2 priority = 5 Name = shsx Station = SHANGHAI priority = 5 rf1 = 2150, 8200 ifname = C, A rf2 = 2450, 8600 pol = RCP, RCP lo1 = 1600, 9100 note = 'From An Tao 18May2006' / ! Name = shsx2 Station = SHANGHAI, SHANG_S2 priority = 6 Name = shsx2 Station = SHANGHAI priority = 6 rf1 = 2150, 8600 ifname = C, A rf2 = 2450, 9000 pol = RCP, RCP lo1 = 1600, 8100 note = 'From An Tao 18May2006' / ! Name = shx Station = SHANGHAI, SHANG_S2 priority = 5 Name = shx Station = SHANGHAI priority = 5 rf1 = 8200, 8200 ifname = C, A rf2 = 8600, 8600 pol = RCP, RCP lo1 = 9100, 9100 note = 'From An Tao 18May2006. Normal X-band' / ! Name = shxd Station = SHANGHAI, SHANG_S2 priority = 5 Name = shxd Station = SHANGHAI priority = 5 rf1 = 8200, 8200 ifname = A, C rf2 = 8600, 8600 pol = RCP, LCP lo1 = 9100, 9100 note = 'From An Tao 18May2006. Dummy dual pol - only RCP available' ! AGP 06Nov2008 Changed the IF allocation RCP on A as usual S/X / ! Name = shxd2 Station = SHANGHAI, SHANG_S2 priority = 6 Name = shxd2 Station = SHANGHAI priority = 6 rf1 = 8600, 8600 ifname = A, C rf2 = 9000, 9000 pol = RCP, LCP lo1 = 8100, 8100 note = 'From An Tao 18May2006. Dummy dual pol - only RCP available' ! AGP 06Nov2008 Changed the IF allocation RCP on A as usual S/X / ! AGP 07Nov2008 Commented out entry below - seems copy of shx above ! but wrong !Name = shx Station = SHANGHAI, SHANG_S2 priority = 6 ! rf1 = 8200, 8600 ifname = C, A ! rf2 = 2450, 9000 ! pol = RCP, RCP lo1 = 1600, 8000 ! note = 'From An Tao 18May2006 ' !/ ! Name = sh1cm Station = SHANGHAI, SHANG_S2 priority = 5 Name = sh1cm Station = SHANGHAI priority = 5 rf1 = 22100, 22100 ifname = C, A rf2 = 22600, 22600 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 21600.0, 21600.0 note = 'From Porcas, from Huang Xinyong 231198' ! ranges guessed assuming a 500 - 1000 MHz BBC / Name = tr30cm.mid Station = TORUN priority = 4 rf1 = 867.5,867.5 ifname = C, A rf2 = 882.5, 882.5 fe = '30cm', '30cm' pol = RCP , LCP lo1 = 1700, 1700 note = '** Dummy setup **; RCV asks if better to avoid low LO1=200 for RFI' ! JFD : After my phone call with A. Kus Thuesday 25 August ! ranges 500 - 1000 BBC range / Name = tr30cm.low Station = TORUN priority = 4 rf1 = 700 , 700 ifname = C, A rf2 = 867.5, 867.5 fe = '30cm', '30cm' pol = RCP , LCP lo1 = 1750, 1750 note = '** Dummy setup **; RCV asks if better to avoid low LO1=200 for RFI' ! JFD : After my phone call with A. Kus Thuesday 25 August ! ranges 500 - 1000 BBC range / Name = tr30cm.high Station = TORUN priority = 4 rf1 = 882.5,882.5 ifname = C, A rf2 = 1105 , 1105 fe = '30cm', '30cm' pol = RCP , LCP lo1 = 1750, 1750 note = '** Dummy setup **; RCV asks if better to avoid low LO1=200 for RFI' ! JFD : After my phone call with A. Kus Thuesday 25 August ! ranges 500 - 1000 BBC range / Name = tr18cm Station = TORUN priority = 3 rf1 = 1350, 1350 ifname = C, A rf2 = 1750, 1750 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 2300, 2300 note = 'E-mail Borkowski 12Mar98, preferred alternative' !changed to 1350 for EH7 Borowski 31/1/00 !CR: changed rf2 from K.Borkowski 12Jan01 / !Name = tr18bcm Station = TORUN priority = 5 ! rf1 = 1500, 1500 ifname = C, A ! rf2 = 1800, 1800 fe = '18cm', '18cm' ! pol = RCP, LCP lo1 = 1000, 1000 ! note = 'E-mail Borkowski 12Mar98, not preferred interference' ! CR: removed 12Jan01 after request by K.Borkowski !/ Name = tr6cmOH Station = TORUN priority = 5 rf1 = 4350, 4350 ifname = C, A rf2 = 4950, 4950 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 3900.0, 3900.0 note = 'E-mail K.Borkowski 23Apr03, alternative (CR 1May03)' / Name = tr6cm Station = TORUN priority = 3 rf1 = 4750, 4750 ifname = C, A rf2 = 5350, 5350 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 4200.0, 4200.0 note = 'E-mail Borkowski 23Apr03 (CR 1May03)' / Name = tr5cmOH Station = TORUN priority = 5 rf1 = 5900, 5900 ifname = C, A rf2 = 6400, 6400 fe = '5cm', '5cm' pol = RCP, LCP lo1 = 5400.0, 5400.0 note = 'Values confirmed by E-mail K.Borkowski (JFD 02Oct98)' / Name = tr5cm Station = TORUN priority = 4 rf1 = 6400, 6400 ifname = C, A rf2 = 6900, 6900 fe = '5cm', '5cm' pol = RCP, LCP lo1 = 5900.0, 5900.0 note = 'Values confirmed by E-mail Borkowski (JFD 26Oct98)' / Name = tr1cm Station = TORUN priority = 3 rf1 = 22000, 22000 ifname = C, A rf2 = 22500, 22500 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 21500, 21500 note = 'Values from Bob Campbell by email (23-04-2013)' / Name = ur90cm Station = URUMQI rf1 = 314, 314 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 337, 337 fe = '90cm', '90cm' pol = RCP, LCP lo1 = 0, 0 note = 'Single polarization only available - may be either RCP or LCP' !CR: From L.Xiang 21 Sep 2004' / Name = ur30cm Station = URUMQI rf1 = 790, 790 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 1120, 1120 fe = '30cm', '30cm' pol = RCP, LCP lo1 = 700, 700 note = 'Severe RFI: 928-963 MHz (GSM), 872-882 MHz (CDMA)' !CR: From L.Xiang 8 Aug 2004' / Name = ur18cm Station = URUMQI rf1 = 1410, 1410 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 1735, 1735 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 1300, 1300 note = 'update L.Xiang 9Feb05' / Name = ursx Station = URUMQI rf1 = 2150, 8200 ifname = '2N', '1N' fe = '13cm', '4cm' rf2 = 2450, 8600 altifn = '1A', '2A' pol = RCP, RCP lo1 = 2020, 8100 note = 'From X.Hong 280300' / ! obsolete since new Urumqi receiver installed !Name = ur6cm Station = URUMQI priority = 1 ! rf1 = 4750 ifname = '1N' fe = '6cm' ! rf2 = 5150 altifn = '2A' ! pol = LCP lo1 = 4620.0 ! note = 'From L.Xiang 280300' ! !CR: update from Lorant (1Dec00) !/ Name = ur6cm Station = URUMQI priority = 1 rf1 = 4720, 4720 ifname = '2N', '1N' fe = '6cm', '6cm' rf2 = 5220, 5220 altifn = '1A', '2A' pol = RCP, LCP lo1 = 4620.0, 4620.0 note = '' !CR: update From L.Xiang 8Aug04' / Name = urx Station = URUMQI priority = 6 rf1 = 8300, 8300 ifname = '2N', '1N' fe = '4cm', '4cm' rf2 = 8580, 8580 altifn = '1A', '2A' pol = RCP, RCP lo1 = 8100, 8100 note = 'single pol entry, only RCP available' ! ranges guessed assuming BBC 220 - 500; copied from onxd / Name = urxd Station = URUMQI priority = 6 rf1 = 8300, 8300 ifname = '2N', '1N' fe = '4cm', '4cm' rf2 = 8580, 8580 altifn = '1A', '2A' pol = LCP, RCP lo1 = 8100, 8100 note = 'dummy dual-pol entry, only RCP available' ! ranges guessed assuming BBC 220 - 500; copied from onxd / Name = ur1cm Station = URUMQI priority = 1 rf1 = 22100, 22100 ifname = '1N' altifn = '2A' rf2 = 24000, 24000 fe = '1cm', '1cm' pol = LCP, LCP lo1 = 22000.0, 22000.0 note = 'From X.Hong 280300' / Name = ur1cmd Station = URUMQI priority = 5 rf1 = 22100, 22100 ifname = '2N','1N' fe = '1cm', '1cm' rf2 = 24000, 24000 altifn = '1A','2A' pol = RCP, LCP lo1 = 22000.0, 22000.0 note = 'Dummy dual-pol entry, only LCP available (CR 2Jul02).' / Name = j1b90cm Station = JODRELL1 priority = 1 rf1 = 314, 314 ifname = '2N', '1N' fe = '90cm', '90cm' rf2 = 336, 336 altifn = '1A', '2A' pol = RCP, LCP lo1 = 150.0, 150.0 note = 'from Burgess, 8 Aug 2004' / Name = jb30cm.EV008B Station = JODRELL1 priority = 4 rf1 = 785.5 , 785.5 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 793.5 , 793.5 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 640.5 , 640.5 note = 'RCV shifted LO1 (thus BBsyn) because HI line in upper part of 8 MHz' ! Obs freq 791.5 MHz / Name = jb30cm.EM034 Station = JODRELL1 priority = 4 rf1 = 846.8 , 846.8 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 854.8 , 854.8 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 699.8 , 699.8 note = 'email from S.Garrington (JFD 24-08-99) to copy Effelsberg' ! Obs freq 848.8 MHz / Name = jb30cm.EP030 Station = JODRELL1 priority = 4 rf1 = 848.49, 848.49 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 856.49, 856.49 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 701.49, 701.49 note = 'email from S.Garrington (JFD 24-08-99) to copy Effelsberg' ! Obs freq 850.49 MHz / Name = jb30cm.EO004C Station = JODRELL1 priority = 4 rf1 = 874.7 , 874.7 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 882.7 , 882.7 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 727.7 , 727.7 note = 'email from S.Garrington (JFD 24-08-99) to copy Effelsberg' ! Obs freq 876.7 MHz / Name = jb30cm.EV008A Station = JODRELL1 priority = 4 rf1 = 882.6 , 882.6 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 890.6 , 890.6 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 737.6 , 737.6 note = 'RCV shifted LO1 (thus BBsyn) because HI line in upper part of 8 MHz' ! Obs freq 888.6 MHz / Name = jb30cm.EB015B Station = JODRELL1 priority = 4 rf1 = 986.7 , 986.7 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 990.7 , 990.7 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 838.7 , 838.7 note = 'RCV shifted LO1 (thus BBsyn) because only 4 MHz needed' ! Obs freq 988.7 MHz / Name = jb30cm.EB015A Station = JODRELL1 priority = 4 rf1 = 986.7 , 986.7 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 994.7 , 994.7 fe = '30cm' , '30cm' pol = RCP , LCP lo1 =839.7 , 839.7 note = 'email from S.Garrington (JFD 24-08-99) to copy Effelsberg' ! Obs freq 988.7 MHz / Name = jb30cm.EO004B Station = JODRELL1 priority = 4 rf1 = 1033.2 , 1033.2 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 1041.2 , 1041.2 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 886.2 , 886.2 note = 'email from S.Garrington (JFD 24-08-99) to copy Effelsberg' ! Obs freq 1035.2 MHz / Name = jb30cm.EO004A Station = JODRELL1 priority = 4 rf1 = 1046.6 , 1046.6 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 1054.6 , 1054.6 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 899.6 , 899.6 note = 'email from S.Garrington (JFD 24-08-99) to copy Effelsberg' ! Obs freq 1048.6 MHz / Name = jb30cm.EP031A Station = JODRELL1 priority = 4 rf1 = 1068.75 , 1068.75 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 1076.75 , 1076.75 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 923.75 , 923.75 note = 'RCV shifted LO1 (thus BBsyn) because HI line in upper part of 8 MHz' ! Obs freq 1074.75 MHz / Name = j121.1cm Station = JODRELL1 priority = 4 rf1 = 1404, 1404 ifname = '2N', '1N' fe = '21cm', '21cm' rf2 = 1420, 1420 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1200, 1200 note = 'Values from E-mail A.Gunn (JFD 07jan99)' ! VC ranges 204 - 220, No VC freq possible above 220MHz. / Name = j121red Station = JODRELL1 priority = 4 rf1 = 1330, 1330 ifname = '2N', '1N' fe = '21cm', '21cm' rf2 = 1430, 1430 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1230, 1230 note = 'Values from SImon Garrington for red HI 21/01/00' ! VC ranges 100 - 200, assuming that's OK / Name = j1b1550 Station = JODRELL1 priority = 5 rf1 = 1550, 1550 ifname = '2N', '1N' fe = '18cm', '18cm' rf2 = 1650, 1650 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1450.0, 1450.0 note 'Special entry red OH Ek10, Garrington 25/1/00' / Name = j1b18cm Station = JODRELL1 priority = 3 rf1 = 1610, 1610 ifname = '2N', '1N' fe = '18cm', '18cm' rf2 = 1730, 1730 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1510.0, 1510.0 note = 'LO from Parry 23Jan97, must be using Low patch' ! ranges guessed assuming 100 - 200 BBC range in low output / Name = j1b6cm Station = JODRELL1 priority = 3 rf1 = 4920, 4920 ifname = '2N', '1N' fe = '6cm', '6cm' rf2 = 5060, 5060 altifn = '1A', '2A' pol = RCP, LCP lo1 = 4840.0, 4840.0 note = 'LO from Spencer 05Jun96, must be using Low patch' ! update from Gunn, 03Sep, use same setup as Mk2 (CR 03Sep25) ! Change ranges for 1Gb/s (AGP 201108) / Name = j1v90cm Station = JB1_VLBA priority = 1 rf1 = 314, 314 ifname = 'A', 'C' fe = '90cm', '90cm' rf2 = 336, 336 pol = RCP, LCP lo1 = 844.0, 844.0 note = 'from Burgess, 8 Aug 2004' / Name = j1v18cm Station = JB1_VLBA priority = 4 rf1 = 1300, 1300 ifname = C, A rf2 = 1730, 1730 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 1110.0, 1110.0 note = 'LO from Burgess 29Apr97' ! ranges guessed assuming a 500 - 1000 MHz BBC / Name = j1v6cm Station = JB1_VLBA priority = 4 rf1 = 4940, 4940 ifname = C, A rf2 = 5400, 5400 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 4440.0, 4440.0 note = 'LO from Paul Burgess 10Jun96' ! Assume same as Mk2 (CR 2003Sep26) / Name = j2b90cm Station = JODRELL2 priority = 1 rf1 = 314, 314 ifname = '2N', '1N' fe = '90cm', '90cm' rf2 = 336, 336 altifn = '1A', '2A' pol = RCP, LCP lo1 = 150.0, 150.0 note = 'from Burgess, 8 Aug 2004' / Name = j2b21cm Station = JODRELL2 priority = 4 rf1 = 1400, 1400 ifname = '2N', '1N' fe = '21cm', '21cm' rf2 = 1430, 1430 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1230.0, 1230.0 note = 'From Burgess via email (CR 29Oct01)' ! ranges guessed assuming 170 - 200 BBC range in low output / Name = j2b18cm Station = JODRELL2 priority = 4 rf1 = 1610, 1610 ifname = '2N', '1N' fe = '18cm', '18cm' rf2 = 1730, 1730 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1510.0, 1510.0 note = 'LO from Parry 23Jan97, assuming ident to JB1' ! rf2=1730 from Alastair Gunn, 31Jan2005 / Name = j2c6cmOH Station = JODRELL2 priority = 5 rf1 = 4700, 4700 ifname = '2N', '1N' fe = '6cm', '6cm' rf2 = 4800, 4800 altifn = '1A', '2A' pol = RCP, LCP lo1 = 4600.0, 4600.0 note = 'Values confirmed by E-mail P.Burgess (JFD 29Sep98)' ! always assume the 100 - 200 BBC range at Jodrell / Name = j2b6cm Station = JODRELL2 priority = 3 rf1 = 4920, 4920 ifname = '2N', '1N' fe = '6cm', '6cm' rf2 = 5060, 5060 altifn = '1A', '2A' pol = RCP, LCP lo1 = 4840.0, 4840.0 note = 'LO from Spencer 05Jun96, must be using Low patch' ! ranges changed for 1Gb/s (AGP 201108) / Name = j2b5cmOH Station = JODRELL2 priority = 5 rf1 = 6000, 6000 ifname = '2N', '1N' fe = '5cm', '5cm' rf2 = 6100, 6100 altifn = '1A', '2A' pol = RCP, LCP lo1 = 5912.0, 5912.0 note = 'Guessed values from PC-SCHED (JFD 05Oct98) ' ! ranges guessed assuming 100 - 200 BBC range ! update from JFD (CR 17Oct01) / Name = j2b5cm Station = JODRELL2 priority = 5 rf1 = 6600, 6600 ifname = '2N', '1N' fe = '5cm', '5cm' rf2 = 6700, 6700 altifn = '1A', '2A' pol = RCP, LCP lo1 = 6520.0, 6520.0 note = 'Values confirmed by E-mail P.Burgess (JFD 26Oct98)' / Name = j2b1cm Station = JODRELL2 priority = 4 rf1 = 22180,22180 ifname = '2N', '1N' fe = '1cm', '1cm' rf2 = 22280,22280 altifn = '1A', '2A' pol = RCP, LCP lo1 = 22080.0,22080.0 note = 'Guess from NET1A in PC-SCHED, must be using Low patch' ! ranges guessed assuming 100 - 200 BBC range in low output / Name = j2b1cmhigh Station = JODRELL2 priority = 4 rf1 = 23500,23500 ifname = '2N', '1N' fe = '1cm', '1cm' rf2 = 23900,23900 altifn = '1A', '2A' pol = RCP, LCP lo1 = 23400.0,23400.0 note = 'for high K-band test, ranges guessed' ! ranges would allow for either low or high patching / Name = j2v90cm Station = JB2_VLBA priority = 1 rf1 = 314, 314 ifname = 'C', 'A' fe = '90cm', '90cm' rf2 = 336, 336 pol = RCP, LCP lo1 = 844.0, 844.0 note = 'from Burgess, 8 Aug 2004' / Name = j2v18cm Station = JB2_VLBA priority = 4 rf1 = 1300, 1300 ifname = C, A rf2 = 1730, 1730 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 1110.0, 1110.0 note = 'LO from Burgess 29Apr97' ! ranges guessed assuming a 500 - 1000 MHz BBC / Name = j2v6cm Station = JB2_VLBA priority = 4 rf1 = 4940, 4940 ifname = C, A rf2 = 5400, 5400 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 4440.0, 4440.0 note = 'LO from Paul Burgess 10Jun96' ! ranges guessed assuming a 500 - 1000 MHz BBC / Name = j2v1cm Station = JB2_VLBA priority = 4 rf1 = 22200,22200 ifname = C, A rf2 = 22600,22600 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 21680.0, 22080.0 note = 'From MkIII and guessing 400 MHz converter, Huib' ! ranges guessed assuming a 500 - 1000 MHz BBC / Name = j2v1cmhigh Station = JB2_VLBA priority = 4 rf1 = 23500,23500 ifname = C, A rf2 = 23900,23900 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 23000.0, 23000.0 note = 'for high K-band test, ranges guessed' ! ranges for 500-900 VLBA-type IF / ! Name = mc21cm Station = MEDICINA priority = 3 rf1 = 1366, 1366 ifname = '2N', '1N' fe = '21cm', '21cm' rf2 = 1446, 1446 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1036.0, 1036.0 note = 'updated from Maccaferri (CR 30Jan01)' ! BBC range 250 - 500 BBC range / Name = mcOHlin Station = MEDICINA priority = 5 rf1 = 1599, 1599 ifname = '2N', '1N' fe = '18cm', '18cm' rf2 = 1679, 1679 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1269.0, 1269.0 note = 'updated from Maccaferri (CR 2Dec00)' / Name = mc18cm Station = MEDICINA priority = 3 rf1 = 1625, 1625 ifname = '2N', '1N' fe = '18cm', '18cm' rf2 = 1705, 1705 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1295.0, 1295.0 note = 'updated from Maccaferri (CR 2Dec00)' / Name = mc_s Station = MEDICINA priority = 4 rf1 = 2200, 2200 ifname = '2N', '1N' fe = '13cm', '13cm' rf2 = 2360, 2360 altifn = '1A', '2A' pol = RCP, LCP lo1 = 2020, 2020 note = 'added from Maccaferri (CR 30Nov00)' / Name = mcsx Station = MEDICINA priority = 5 rf1 = 2200, 8180 ifname = '2N', '1N' fe = '13cm', '4cm' rf2 = 2360, 8580 altifn = '1A', '2A' pol = RCP, RCP lo1 = 2020, 8080 note = 'Updated from Maccaferri (CR 30Jan01)' / Name = mc6cm Station = MEDICINA priority = 3 rf1 = 4700, 4700 ifname = '2N', '1N' fe = '6cm', '6cm' rf2 = 5100, 5100 altifn = '1A', '2A' pol = RCP, LCP lo1 = 4600.0, 4600.0 note = 'Values confirmed by E-mail A.Orfei (JFD 2Oct98)' ! BBC range 100 - 500, Maccaferri 11/2000 (CR) / Name = mc6cmOH Station = MEDICINA priority = 5 rf1 = 4700, 4700 ifname = '2N', '1N' fe = '6cm', '6cm' rf2 = 5100, 5100 altifn = '1A', '2A' pol = RCP, LCP lo1 = 4600.0, 4600.0 note = 'Values confirmed by E-mail A.Orfei (JFD 2Oct98)' ! BBC ranges 100-500. ! same settings as mc6cm - Maccaferri 30Jan01 (CR) / Name = mc5cmOH Station = MEDICINA priority = 5 rf1 = 5900, 5900 ifname = '2N', '1N' fe = '5cm', '5cm' rf2 = 6300, 6300 altifn = '1A', '2A' pol = RCP, LCP lo1 = 5800.0, 5800.0 note = 'Updated by E-mail Orlati (CR 15Nov2004)' / Name = mc5cm Station = MEDICINA priority = 5 rf1 = 6500, 6500 ifname = '2N', '1N' fe = '5cm', '5cm' rf2 = 6900, 6900 altifn = '1A', '2A' pol = RCP, LCP lo1 = 6400.0, 6400.0 note = 'Updated by e-mail Orlati (13Feb2006)' / Name = mc_x Station = MEDICINA priority = 4 rf1 = 8180, 8180 ifname = '1N', '2N' fe = '4cm', '4cm' rf2 = 8580, 8580 altifn = '2A', '1A' pol = RCP, LCP lo1 = 8080, 8080 note = 'changed Maccaferri (CR 30Jan01)' / Name = mcredH2O Station = MEDICINA priority = 4 rf1 = 21860,21860 ifname = '2N', '1N' fe = '1cm', '1cm' rf2 = 22260,22260 altifn = '1A', '2A' pol = RCP, LCP lo1 = 21760.0,21760.0 note = 'Special entry by Lincoln Greenhill for red H2O' ! Change to reflect alternate permitted tuning of LO chain as ! indicated on astbo1 web site. / Name = mc13mm Station = MEDICINA priority = 4 rf1 = 22064,22064 ifname = '2N', '1N' fe = '13mm', '13mm' rf2 = 22464,22464 altifn = '1A', '2A' pol = RCP, LCP lo1 = 21964.0, 21964.0 note = 'values confirmed Maccaferri (CR 30Nov00)' ! typo on rf2 corrected and Name changed from mc1cm (CR 29Jan01) / !Name = mc7mm_sio Station = MEDICINA priority = 4 ! rf1 = 42850 ifname = '1N' fe = '7mm' ! rf2 = 43250 altifn = '2A' ! pol = LCP lo1 = 42750.0 ! note = ' ** LCP only **, values from E-mail A.Orfei (JFD 18jan99) ' ! ! only single Pol LCP, the receiver is shared with Noto !/ !Name = mc7mm_d Station = MEDICINA priority = 5 ! rf1 = 42850, 42850 ifname = '2N', '1N' fe = '7mm' ! rf2 = 43250, 43250 altifn = '1A', '2A' ! pol = RCP, LCP lo1 = 42750.0, 42750.0 ! note = 'Dummy dual-pol entry, only LCP available (CR 2Jul02).' !/ Name = ons18cm Station = ONSALA60 priority = 5 note = 'No 18cm on smaller On dish' / Name = ons6cm Station = ONSALA60 priority = 5 note = 'No 6cm on smaller On dish??' / Name = onsx Station = ONSALA60 priority = 5 rf1 = 2240, 8300 ifname = '2N', '1N' fe = '13cm', '4cm' rf2 = 2520, 8580 altifn = '1A', '2A' pol = RCP, RCP lo1 = 2020, 8080 note = 'Antonis Polatidis 210897' ! ranges guessed assuming BBC 220 - 500 / Name = onxd Station = ONSALA60 priority = 6 rf1 = 8300, 8300 ifname = '2N', '1N' fe = '4cm', '4cm' rf2 = 8580, 8580 altifn = '1A', '2A' pol = LCP, RCP lo1 = 8080, 8080 note = 'On is dual pol X band since 2007' ! ranges guessed assuming BBC 220 - 500 / Name = ons1cm Station = ONSALA60 priority = 4 rf1 = 22120,22120 ifname = '2N', '1N' fe = '1cm', '1cm' rf2 = 22400,22400 altifn = '1A', '2A' pol = RCP, LCP lo1 = 21900.0,21900.0 note = 'Conway in my office 28Jan97, must be High patch' ! ranges guessed assuming BBC 220 - 500 corrected 000217 LJG/HJvL / Name = ons1cmhigh Station = ONSALA60 priority = 4 rf1 = 23500,23500 ifname = '2N', '1N' fe = '1cm', '1cm' rf2 = 23900,23900 altifn = '1A', '2A' pol = RCP, LCP lo1 = 23400.0,23400.0 note = 'for high K-band test, ranges guessed' / !Name = ons_x Station = ONSALA60 priority = 3 ! rf1 = 8300, 8300 ifname = '2N', '1N' fe = '4cm', '4cm' ! rf2 = 8580, 8580 altifn = '1A', '2A' ! pol = RCP, RCP lo1 = 8080.0, 8080.0 ! note = 'From Polatidis, 13/8/97 RCP only' ! ! ranges guessed assuming BBC 220 - 500 ! Removed at request of Polatidis (CR 3Jul01) !/ Name = on7mm_sio Station = ONSALA60 priority = 4 rf1 = 42800 ifname = '1N' fe = '7mm' rf2 = 43200 altifn = '2A' pol = LCP lo1 = 42700.0 note = ' ** LCP only **, values from E-mail J.Conway (JFD 12jan99) ' ! only single Pol LCP, BBC range ~100-500MHz / Name = on7mm_sio2 Station = ONSALA60 priority = 5 rf1 = 42900 ifname = '1N' fe = '7mm' rf2 = 43300 altifn = '2A' pol = LCP lo1 = 42800.00 note = ' ** LCP only **, values from E-mail J.Conway (JFD 12jan99) ' ! only single Pol LCP, BBC range ~100-500MHz / ! ! ONSALA at 3 mm Name = 3mm_onsala Station = ONSALA60 Priority = 0 rf1 = 86150, 86150 ifname = '1N', '2N' altifn = '1A', '2A' rf2 = 86440, 86440 fe = '3mm', '3mm' pol = LCP, RCP lo1 = 85900, 85900 / ! ONSALA at 3 mm 256-16-1 no pol ! added for Oct 2000, CMVA session, since other setup produces errors, TPK Name = 3mm_onsa-lcp STATION = ONSALA60 Priority = 0 rf1 = 86150, 86150 ifname = '1N', '2N' altifn = '1A', '2A' rf2 = 86440, 86440 fe = '3mm', '3mm' pol = LCP, LCP lo1 = 85900, 85900 / Name = on30cm.low Station = ONSALA85 priority = 4 rf1 = 780 , 780 ifname = '2N' , '1N' fe = '30cm' , '30cm' rf2 = 900 , 900 altifn = '1A' , '2A' pol = RCP, LCP lo1 = 650 , 650 note = 'Confirmed by email J.Conway (JFD 25-08-99)' / Name = on30cm.mid Station = ONSALA85 priority = 4 rf1 = 800 , 800 ifname = '2N' , '1N' fe = '30cm' , '30cm' rf2 = 920 , 920 altifn = '1A' , '2A' pol = RCP, LCP lo1 = 700 , 700 note = 'Confirmed by email J.Conway (JFD 25-08-99)' / Name = on30cm.high Station = ONSALA85 priority = 4 rf1 = 975 , 975 ifname = '2N' , '1N' fe = '30cm' , '30cm' rf2 = 1200 , 1200 altifn = '1A' , '2A' pol = RCP, LCP lo1 = 700 , 700 note = 'Confirmed by email J.Conway (JFD 25-08-99)' / Name = on21cm3 Station = ONSALA85 priority = 3 rf1 = 1100, 1100 ifname = '2N', '1N' fe = '21cm', '21cm' rf2 = 1230, 1230 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1000, 1000 note = 'Values from E-mail J.Conway (CR 21Oct02)' ! tunable LO, several LOs specified. / Name = on21cm4 Station = ONSALA85 priority = 4 rf1 = 1200, 1200 ifname = '2N', '1N' fe = '21cm', '21cm' rf2 = 1330, 1330 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1100, 1100 note = 'Values from E-mail J.Conway (CR 21Oct02)' ! tunable LO, several LOs specified. Higher freq LOs have higher priority. / Name = on21cm2 Station = ONSALA85 priority = 2 rf1 = 1300, 1300 ifname = '2N', '1N' fe = '21cm', '21cm' rf2 = 1430, 1430 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1200, 1200 note = 'Values from E-mail J.Conway (CR 21Oct02)' ! tunable LO, several LOs specified. / Name = on21cm5 Station = ONSALA85 priority = 5 rf1 = 1400, 1400 ifname = '2N', '1N' fe = '21cm', '21cm' rf2 = 1530, 1530 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1300, 1300 note = 'Values from E-mail J.Conway (CR 21Oct02)' ! tunable LO, several LOs specified. Higher freq LOs have higher priority. / Name = on21cm6 Station = ONSALA85 priority = 6 rf1 = 1500, 1500 ifname = '2N', '1N' fe = '21cm', '21cm' rf2 = 1630, 1630 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1400, 1400 note = 'Values from E-mail J.Conway (CR 21Oct02)' ! tunable LO, several LOs specified. Higher freq LOs have higher priority. / Name = onb18cm Station = ONSALA85 priority = 0 rf1 = 1600, 1600 ifname = '2N', '1N' fe = '18cm', '18cm' rf2 = 1720, 1720 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1220.0, 1220.0 note = 'emails from M. Lindqvist 8-10 apr 2012' ! ranges guessed assuming 100 - 200 BBC / Name = on21cmNEW Station = ONSALA85 priority = 1 rf1 = 1320, 1320 ifname = '2N', '1N' fe = '21cm', '21cm' rf2 = 1440, 1440 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1220, 1220 note = 'emails from M. Lindqvist 8-10 apr 2012' / Name = on21cm1 Station = ONSALA85 priority = 1 rf1 = 1600, 1600 ifname = '2N', '1N' fe = '21cm', '21cm' rf2 = 1730, 1730 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1500, 1500 note = 'Values from E-mail J.Conway (CR 21Oct02)' ! tunable LO, several LOs specified. / Name = on21cm7 Station = ONSALA85 priority = 7 rf1 = 1700, 1700 ifname = '2N', '1N' fe = '21cm', '21cm' rf2 = 1830, 1830 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1600, 1600 note = 'Values from E-mail J.Conway (CR 21Oct02)' ! tunable LO, several LOs specified. Higher freq LOs have higher priority. / Name = onb6cmOH Station = ONSALA85 priority = 3 rf1 = 4700, 4700 ifname = '2N', '1N' fe = '6cm', '6cm' rf2 = 4920, 4920 altifn = '1A', '2A' pol = RCP, LCP lo1 = 4600.0, 4600.0 note = 'Values confirmed by E-mail J.Conway (JFD 17Oct01)' ! ranges guessed assuming 100 - 220 BBC range ! update from JFD (CR 17Oct01) / Name = onb6cm Station = ONSALA85 priority = 3 rf1 = 4920, 4920 ifname = '2N', '1N' fe = '6cm', '6cm' rf2 = 5060, 5060 altifn = '1A', '2A' pol = RCP, LCP lo1 = 4830.0, 4830.0 note = 'email from Lindqvist (25May2007), must be Low patch' ! ranges changed for 1Gb/s AGP 201108 / Name = onb5cmOH Station = ONSALA85 priority = 5 rf1 = 6000, 6000 ifname = '2N', '1N' fe = '5cm', '5cm' rf2 = 6125, 6125 altifn = '1A', '2A' pol = RCP, LCP lo1 = 5900.0, 5900.0 note = 'Values confirmed by E-mail J.Conway(CR 18Jan02)' ! IF filter 75-22MHz, BBC ranges 100- 225 BBC; / Name = on5cm Station = ONSALA85 priority = 5 rf1 = 6600, 6600 ifname = '2N', '1N' fe = '5cm', '5cm' rf2 = 6725, 6725 altifn = '1A', '2A' pol = RCP, LCP lo1 = 6250.0, 6250.0 note = 'emails from M. Lindqvust 8-10 apr 2012' / Name = onb1cm Station = ONSALA85 priority = 5 note = 'No 1 cm on larger Onsala dish' / Name = wb90cm station = WSTRBORK priority = 2 rf1 = 310, 310 ifname = '2N', '1N' fe = '5cm', '5cm' rf2 = 380, 380 altifn = '1A', '2A' pol = RCP, LCP lo1 = 200.0, 200.0 note = 'Best estimates for now' ! From Foley 21 Sep 2004 (CR 040921) / Name = wb30cm.EV008B Station = WSTRBORK priority = 4 rf1 = 785.5 , 785.5 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 793.5 , 793.5 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 653.45, 653.45 note = '** not final ** tuning must be re-calculated at WSRT (JFD 25/08/99)' ! supplied by Vermeulen 25/08/1999 ! Obs freq 791.5 MHz / Name = wb30cm.EM034 Station = WSTRBORK priority = 4 rf1 = 846.8 , 846.8 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 854.8 , 854.8 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 714.75, 714.75 note = '** not final ** tuning must be re-calculated at WSRT (JFD 25/08/99)' ! supplied by Vermeulen 25/08/1999 ! Obs freq 848.8 MHz / Name = wb30cm.EP030 Station = WSTRBORK priority = 4 rf1 = 848.49, 848.49 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 856.49, 856.49 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 716.44, 716.44 note = '** not final ** tuning must be re-calculated at WSRT (JFD 25/08/99)' ! supplied by Vermeulen 25/08/1999 ! Obs freq 850.49 MHz / Name = wb30cm.EO004C Station = WSTRBORK priority = 4 rf1 = 874.7 , 874.7 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 882.7 , 882.7 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 742.65, 742.65 note = '** not final ** tuning must be re-calculated at WSRT (JFD 25/08/99)' ! supplied by Vermeulen 25/08/1999 ! Obs freq 876.7 MHz / Name = wb30cm.EV008A Station = WSTRBORK priority = 4 rf1 = 882.6 , 882.6 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 890.6 , 890.6 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 750.55, 750.55 note = '** not final ** tuning must be re-calculated at WSRT (JFD 25/08/99)' ! supplied by Vermeulen 25/08/1999 ! Obs freq 888.6 MHz / Name = wb30cm.EB015B Station = WSTRBORK priority = 4 rf1 = 986.7 , 986.7 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 990.7 , 990.7 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 854.65, 854.65 note = '** not final ** tuning must be re-calculated at WSRT (JFD 25/08/99)' ! supplied by Vermeulen 25/08/1999 ! Obs freq 988.7 MHz / Name = wb30cm.EB015A Station = WSTRBORK priority = 4 rf1 = 986.7 , 986.7 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 994.7 , 994.7 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 854.65, 854.65 note = '** not final ** tuning must be re-calculated at WSRT (JFD 25/08/99)' ! supplied by Vermeulen 25/08/1999 ! Obs freq 988.7 MHz / Name = wb30cm.EO004B Station = WSTRBORK priority = 4 rf1 = 1033.2 , 1033.2 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 1041.2 , 1041.2 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 901.15, 901.15 note = '** not final ** tuning must be re-calculated at WSRT (JFD 25/08/99)' ! supplied by Vermeulen 25/08/1999 ! Obs freq 1035.2 MHz / Name = wb30cm.EO004A Station = WSTRBORK priority = 4 rf1 = 1046.6 , 1046.6 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 1054.6 , 1054.6 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 914.55, 914.55 note = '** not final ** tuning must be re-calculated at WSRT (JFD 25/08/99)' ! supplied by Vermeulen 25/08/1999 ! Obs freq 1048.6 MHz / Name = wb30cm.EP031A Station = WSTRBORK priority = 4 rf1 = 1068.75 , 1068.75 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 1076.75 , 1076.75 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 936.7, 936.7 note = '** not final ** tuning must be re-calculated at WSRT (JFD 25/08/99)' ! supplied by Vermeulen 25/08/1999 ! Obs freq 1074.75 MHz / Name = wb30cm.VAH1 Station = WSTRBORK priority = 4 rf1 = 1123.2 , 1123.2 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 1131.2 , 1131.2 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 991.15, 991.15 note = '** not final ** tuning must be re-calculated at WSRT (JFD 25/08/99)' ! supplied by Vermeulen 25/08/1999 ! Obs freq 1125.2 MHz / Name = wb22.6cm Station = WSTRBORK priority = 4 rf1 = 1240, 1240 ifname = '2N', '1N' fe = '21cm', '21cm' rf2 = 1340, 1340 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1145.0, 1145.0 note = 'Values from E-mail T.Foley (JFD 07jan99)' ! BBC ranges 100 - 220 BBC; / Name = wb30cm.EP031B Station = WSTRBORK priority = 4 rf1 = 1163.25 , 1163.25 ifname = '2N' , '1N' altifn = '1A' , '2A' rf2 = 1171.25 , 1171.25 fe = '30cm' , '30cm' pol = RCP , LCP lo1 = 1031.2 , 1031.2 note = '** not final ** tuning must be re-calculated at WSRT (JFD 25/08/99)' ! supplied by Vermeulen 25/08/1999 ! Obs freq 1165.25 MHz / Name = wb21.1cm Station = WSTRBORK priority = 3 rf1 = 1360, 1360 ifname = '2N', '1N' fe = '21cm', '21cm' rf2 = 1460, 1460 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1265.0, 1265.0 note = 'Values from E-mail T.Foley (JFD 07jan99)' ! BBC ranges 100 - 220 BBC; / Name = wb1530 Station = WSTRBORK priority = 5 rf1 = 1530, 1530 ifname = '2N', '1N' fe = '18cm', '18cm' rf2 = 1660, 1660 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1440.0, 1440.0 note = 'Special entry red OH Ek10 Foley 25/1/00' ! ranges guessed assuming BBC 90 - 220 / Name = wb18cm Station = WSTRBORK priority = 3 rf1 = 1600, 1600 ifname = '2N', '1N' fe = '18cm', '18cm' rf2 = 1730, 1730 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1510.0, 1510.0 note = 'E-mail Foley 22Jan97 MFFE, must be using Low patch' ! ranges guessed assuming BBC 100 - 220 / Name = wbsx Station = WSTRBORK priority = 5 rf1 = 2240, 8300 ifname = '2N', '1N' fe = '13cm', '4cm' rf2 = 2520, 8580 altifn = '1A', '2A' pol = RCP, RCP lo1 = 2020.0, 8080.0 note = 'Wild guess from SX PC-Sched assuming high patch' / Name = wb6cmOH Station = WSTRBORK priority = 5 rf1 = 4750, 4750 ifname = '2N', '1N' fe = '6cm', '6cm' rf2 = 4850, 4850 altifn = '1A', '2A' pol = RCP, LCP lo1 = 4640.0, 4640.0 note = 'Values confirmed by E-mail T.Foley (JFD 2Oct98)' / !!fmo091123: disable on advice of zsolt; wb6cm is now identical. !Name = wb6cm_l Station = WSTRBORK priority = 2 ! rf1 = 4800, 4800 ifname = '2N', '1N' fe = '6cm', '6cm' ! rf2 = 5060, 5060 altifn = '1A', '2A' !! pol = RCP, LCP lo1 = 4820.0, 4820.0 ! pol = RCP, LCP lo1 = 4840.0, 4840.0 !! changed LO to 4840 for 1Gb/s - fictitious number 201108 ! note = 'Non-standard requested by VSOP project OK-d foley 290198' !! Prefered for 1Gb/s and eVLBI - changed rf1-rf2 OK-d Foley 201108 !/ Name = wb6cm Station = WSTRBORK priority = 3 rf1 = 4800, 4800 ifname = '2N', '1N' fe = '6cm', '6cm' rf2 = 5060, 5060 altifn = '1A', '2A' pol = RCP, LCP lo1 = 4840.0, 4840.0 note = 'LO from PC-SCHED values, must be in Low patch' ! Changed rf1-rf2 for 1Gb/s OK-d Foley 201108 / Name = wb5 Station = WSTRBORK priority = 4 rf1 = 6000, 6000 ifname = '2N', '1N' fe = '5cm', '5cm' rf2 = 6200, 6200 altifn = '1A', '2A' pol = RCP, LCP lo1 = 5900.0, 5900.0 note = 'Update from Foley, 25 Jan 2005' ! 6000 MHz is really at the edge of the receiver band / Name = wb5a Station = WSTRBORK priority = 0 rf1 = 6600, 6600 ifname = '2N', '1N' fe = '5cm', '5cm' rf2 = 6700, 6700 altifn = '1A', '2A' pol = RCP, LCP lo1 = 6500.0, 6500.0 note = 'Best estimates for now' ! From Foley 21 Sep 2004 (CR 040921) / Name = wb_x Station = WSTRBORK priority = 4 rf1 = 8300, 8300 ifname = '2N', '1N' fe = '4cm', '4cm' rf2 = 8580, 8580 altifn = '1A', '2A' pol = RCP, LCP lo1 = 8080.0, 8080.0 note = 'Wild guess from SX PC-Sched assuming high patch' / Name = wb1cm Station = WSTRBORK priority = 5 note = 'No 1 cm at WB; 1 cm just drips through the chickenwire' / Name = yb_sx Station = YEBES priority = 5 rf1 = 2210, 8130 ifname = C, A rf2 = 2350, 8630 fe = '13cm', '4cm' pol = RCP, RCP lo1 = 1530, 7650 note = 'From vicente@cay.oan.es Thu May 29 12:52:22 1997' ! Relevant for the Yb 14m now obsolete / Name = yb7mm Station = YEBES priority = 4 rf1 = 41000 ifname = C, A rf2 = 49000 fe = '0.7cm' pol = LCP lo1 = 40900 note = 'LO tunable according to Vicente, just put something arbitrary' ! Relevant to Yb 14m - probably obsolete 211108 AGP / Name = yb7mm_sio Station = YEBES priority = 0 rf1 = 43000, 43000 ifname = C, A rf2 = 43300, 43300 fe = '7mm', '7mm' pol = LCP, LCP lo1 = 42400, 42400 note = ' ** LCP only **, (JFD 15jan99) ' ! Guess BBCs range ~600-900MHz / Name = ys40_sx Station = YEBES40M priority = 4 rf1 = 2200, 8180 ifname = B, A rf2 = 2370, 8650 fe = '13cm', '4cm' pol = RCP,RCP lo1 = 1530, 7650 note = 'OK email de Vicente 151008 - investigate further ' / Name = ys40_4cm Station = YEBES40M priority = 4 rf1 = 8180, 8180 ifname = C, A rf2 = 8650, 8650 fe = '4cm', '4cm' pol = LCP,RCP lo1 = 7650, 7650 note = 'LO taken from D.Grahams S/X configuration for EK028A' / Name = ys40_1cm Station = YEBES40M priority = 4 rf1 = 21650,21650 ifname = C, A rf2 = 22850,22850 fe = '1cm' pol = LCP,RCP lo1 = 21550,21550 note ='LO value by Francisco Colomer (21MAY08), BBC 500-1000MHz' / Name = ys40_1cm_nh3 Station = YEBES40M priority = 4 rf1 = 23350,23350 ifname = C, A rf2 = 24450,24450 fe = '1cm' pol = LCP,RCP lo1 = 23150,23150 note ='LO value by Francisco Colomer (21MAY08), BBC 500-1000MHz' / Name = ys40_5cmOH Station = YEBES40M priority = 4 rf1 = 5780,5780 ifname = C, A rf2 = 6280,6280 fe = '5cm', '5cm' pol = LCP,RCP lo1 = 5280, 5280 note ='RF values by de Vicente (FEB09), BBC 500-1000MHz' / Name = ys40_5cm Station = YEBES40M priority = 4 rf1 = 5900,5900 ifname = C, A rf2 = 6900,6900 fe = '5cm', '5cm' pol = LCP,RCP lo1 = 5910, 5910 ! 'P. de Vicente (apr09) note ='RF and LO values by de Vicente (FEB09), BBC 500-1000MHz' / Name = ys40_6cm Station = YEBES40M priority = 4 rf1 = 4560, 4560 ifname = C, A rf2 = 5060, 5060 fe = '6cm', '6cm' pol = LCP,RCP lo1 = 4158, 4158 note = 'P. de Vicente (apr09)' / ! ! ! Name = hh21cm Station = HART, HART_S2 priority = 5 ! note = 'No 21cm at HartRAO' ! / Name = hh18cm Station = HART priority = 3 rf1 = 1600, 1600 ifname = 'A1', 'B1' fe = '18cm', '18cm' rf2 = 1730, 1730 altifn = 'B2', 'A2' pol = RCP, LCP lo1 = 1510.0, 1510.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / Name = hh13cm Station = HART priority = 3 rf1 = 2210, 2210 ifname = 'A1', 'B1' fe = '13cm', '13cm' rf2 = 2450, 2450 altifn = 'B2', 'A2' pol = RCP, LCP lo1 = 2020.0, 2020.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / Name = hhsx Station = HART priority = 3 rf1 = 2210, 8180 ifname = 'C1', 'A1' fe = '13cm', '4cm' rf2 = 2450, 8980 altifn = 'A2', 'B2' pol = RCP, RCP lo1 = 2020.0, 8080.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / Name = hh13cm_S2 Station = HART priority = 4 rf1 = 2225, 2225 ifname = 'A1', 'B1' fe = '13cm', '13cm' rf2 = 2375, 2375 altifn = 'B2', 'A2' pol = RCP, LCP lo1 = 2120.0, 2120.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / Name = hh6cm_S2 Station = HART priority = 4 rf1 = 4650, 4650 ifname = 'A1', 'B1' fe = '6cm', '6cm' rf2 = 5160, 5160 altifn = 'B2', 'A2' pol = RCP, LCP lo1 = 4600.0, 4600.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / Name = hh6cm Station = HART priority = 3 rf1 = 4700, 4700 ifname = 'A1', 'B1' fe = '6cm', '6cm' rf2 = 5100, 5100 altifn = 'B2', 'A2' pol = RCP, LCP lo1 = 4600.0, 4600.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / Name = hh5cmOH Station = HART priority = 4 rf1 = 6020, 6020 ifname = 'A1', 'B1' fe = '5cm', '5cm' rf2 = 6052, 6052 altifn = 'B2', 'A2' pol = RCP, LCP lo1 = 5880.0, 5880.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / Name = hh5cm Station = HART priority = 4 rf1 = 6650, 6650 ifname = 'A1', 'B1' fe = '5cm', '5cm' rf2 = 6682, 6682 altifn = 'B2', 'A2' pol = RCP, LCP lo1 = 6510.0, 6510.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / Name = hh4cm Station = HART priority = 3 rf1 = 8180, 8180 ifname = 'A1', 'B1' fe = '4cm', '4cm' rf2 = 8980, 8980 altifn = 'B2', 'A2' pol = RCP, LCP lo1 = 8080.0, 8080.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / Name = hh4cm_S2 Station = HART priority = 4 rf1 = 8335, 8335 ifname = 'A1', 'B1' fe = '4cm', '4cm' rf2 = 8505, 8505 altifn = 'B2', 'A2' pol = RCP, LCP lo1 = 8265.0, 8265.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / Name = hh3cm Station = HART priority = 6 rf1 = 12070, 12070 ifname = 'A1', 'B1' fe = '3cm', '3cm' rf2 = 12240, 12240 altifn = 'B2', 'A2' pol = RCP, LCP lo1 = 12021.0, 12021.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / ! Name = hh2cm Station = HART, HART_S2 priority = 5 ! note = 'No 2cm at HartRAO' ! / Name = hh1cm Station = HART priority = 3 rf1 = 21400,21400 ifname = 'A1', 'B1' fe = '1cm', '1cm' rf2 = 24100,24100 altifn = 'B2', 'A2' pol = RCP, LCP lo1 = 22080.0,22080.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / Name = hh1cm_nh3_low Station = HART priority = 3 rf1 = 23600,23600 ifname = 'A1', 'B1' fe = '1cm', '1cm' rf2 = 23800,23800 altifn = 'B2', 'A2' pol = RCP, LCP lo1 = 23550.0,23550.0 note = 'LO selected for NH3 lines 23.6-23.7MHz, suggested by JQ' note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / Name = hh1cm_nh3_hi Station = HART priority = 3 rf1 = 23800,23800 ifname = 'A1', 'B1' fe = '1cm', '1cm' rf2 = 24000,24000 altifn = 'B2', 'A2' pol = RCP, LCP lo1 = 23710.0,23710.0 note = 'LO selected for NH3 line 23.9MHz, suggested by JQ' note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / ! Name = hh1cm_vlba Station = HART, HART_S2 priority = 3 Name = hh1cm_vlba Station = HART priority = 3 rf1 = 23750,23750 ifname = 'A1', 'B1' fe = '1cm', '1cm' rf2 = 23850,23850 altifn = 'B2', 'A2' pol = RCP, LCP lo1 = 23640.0,23640.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / ! Name = hh7mm Station = HART, HART_S2 priority = 5 ! note = 'No 7mm at HartRAO' ! / ! Setups for the Hart15m, with DBBC Name = ht4cm Station = HART15M priority = 4 rf1 = 8180, 8180 ifname = A1, B1 rf2 = 8980, 8980 altifn = B2, C2 pol = RCP, LCP lo1 = 8080.0, 8080.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / Name = ht13cm Station = HART15M priority = 4 rf1 = 2025, 2025 ifname = A3, B3 rf2 = 2520, 2520 altifn = B4, C3 pol = RCP, LCP lo1 = 2020.0, 2020.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / Name = htsx Station = HART15M priority = 4 rf1 = 8180, 2025 ifname = A1, C1 rf2 = 8980, 2520 altifn = B2, B4 pol = RCP, RCP lo1 = 8080.0, 2020.0 note = 'Values confirmed by E-mail Jonathan Quick 20140219 (CR)' / ! ===================================================================== ! The following entries in the SCHED frequency catalog are for geodetic ! VLBI stations. ! ===================================================================== Name = wzsx Station = WETTZELL priority = 5 rf1 = 2210, 8219 ifname = '2N', '1N' rf2 = 2360, 8865 fe = '13cm', '4cm' pol = RCP, RCP lo1 = 2020, 8080 note = 'Estimates from Lorant sjouwerman@jive.nl May 2000; OK 02/05/00/RK' !CR: updates from Lorant (1Dec00) / Name = nysx Station = NYALES20 priority = 5 rf1 = 2210, 8180 ifname = '2N', '1N' rf2 = 2350, 8980 fe = '13cm', '4cm' pol = RCP, RCP lo1 = 2020, 8080 note = 'Estimates from Lorant sjouwerman@jive.nl May 2000; OK?03/05/00/HD' !CR: updates from Lorant (1Dec00) / Name = masx Station = MATERA priority = 5 rf1 = 2210, 8180 ifname = '2N', '1N' ! LORANT rf2 = 2450, 8980 fe = '13cm', '4cm' pol = RCP, RCP lo1 = 2020, 8080 note = 'Estimates from Lorant sjouwerman@jive.nl May 2000' !CR: updates from Lorant (1Dec00) / ! ===================================================================== ! The following entries in the SCHED frequency catalog are for mm (GMVA) ! VLBI stations in Europe. ! ===================================================================== ! Plateau de Bure (IRAM) at 3 mm, single pol Name = 3mm_pdbure-lcp Station = PDBURE Priority = 0 rf1 = 85800, 85800 ifname = '1N', '2N' altifn = '1A', '2A' rf2 = 86400, 86400 fe = '3mm', '3mm' pol = LCP, LCP lo1 = 85919, 85919 note = '3-mm CMVA' / ! Plateau de Bure (IRAM) at 3 mm Name = 3mm_pdbure Station = PDBURE Priority = 0 rf1 = 85800, 85800 ifname = '1N', '2N' altifn = '1A', '2A' rf2 = 86400, 86400 fe = '3mm', '3mm' pol = LCP, RCP lo1 = 85919, 85919 note = '3-mm CMVA' / ! Pico Veleta (IRAM) at 3 mm ! Name = 3mm_picovel Station = PICOVEL Priority = 0 rf1 = 86007, 86007 ifname = C, A rf2 = 86507, 86507 fe = '3mm', '3mm' pol = RCP, LCP lo1 = 85507, 85507 note = '3-mm CMVA' / ! Pico Veleta (IRAM) at 2 mm ! Name = 2mm_pico-l Station = PICOVEL Priority = 0 rf1 = 128000,128000 ifname = B, D rf2 = 130000,130000 fe = '2mm', '2mm' pol = LCP, LCP lo1 = 128670,128670 note = '2-mm test' / ! ===================================================================== ! Chinese stations added sep 2009 ! ===================================================================== Name = kmsx Station = KUNMING rf1 = 2150, 8200 ifname = B, A rf2 = 2450, 8600 fe = '13cm', '4cm' pol = RCP, RCP lo1 = 1600, 9100 note = 'From Hao Longfei 11 may 2009' / Name = mysx Station = MIYUN50 rf1 = 2150, 8200 ifname = B, A rf2 = 2450, 8600 fe = '13cm', '4cm' pol = RCP, RCP lo1 = 1600, 9100 note = 'From ZHU Xinying 6 July 2009' / ! ===================================================================== ! Robledo 7mm added 2009 Sep 24 (Bob Campbell) ! (an example Cristina worked out for GB065B -- the LO is ! tunable; the Q-band LNA works from 39-49 GHz, and the max recording ! bandwidth is 70 MHz within that) ! ===================================================================== Name = ro7mm Station = ROB34BWG priority = 5 rf1 = 43156 , 43156 ifname = '2N', '1N' fe = '7mm', '7mm' rf2 = 43226 , 43226 altifn = '1A', '2A' pol = RCP, LCP lo1 = 42870.00 , 42870.00 note = 'new 7mm RX, configuration appropriate for GB065B' / ! ! ===================================================================== ! The following entries in the SCHED frequency catalog are for stations ! of the Asia Pacific Telescope. ! These stations are maintained in file freq_APT.dat. ! Remove S2 July 22, 2010 RCW. (Kashima only). ! ===================================================================== Name = us18cm Station = USUDA, USUDAVL, USUDA64 priority = 5 rf1 = 1600, 1600 ifname = A, C rf2 = 1730, 1730 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 750, 750 note = 'LO and rf* from Kenta Fujisawa, e-mail 27/01/97 other values guesses' ! adding values by Kenta to obtain total LO ! confirmed ok May 1999 by K Fujisawa / Name = us6cm Station = USUDA, USUDAVL, USUDA64 priority = 5 rf1 = 4740, 4740 ifname = A, C rf2 = 5140, 5140 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 4140, 4140 note = 'LO and rf* from Kenta Fujisawa, e-mail 27/01/97 other values guesses' ! adding values by Kenta to obtain total LO ! updated may 1999 with information from K Fujisawa / Name = us1cm Station = USUDA, USUDAVL, USUDA64 priority = 5 rf1 = 21900, 21900 ifname = A, C rf2 = 22300, 22300 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 21300.0, 21300.0 note = 'LO and rf* from Kenta Fujisawa, e-mail 27/01/97 other values guesses' ! adding vlues by Kenta to obtain total LO ! updated may 1999 with information from K Fujisawa / Name = ka18cm Station = KASHIM34 priority = 5 rf1 = 1600, 1600 ifname = A, C rf2 = 1800, 1800 fe = '18cm', '18cm' pol = RCP, LCP lo1 = 1250.00, 1250.00 ! updated may 1999 with information from KM Shibata / Name = ka6cm Station = KASHIM34 priority = 5 rf1 = 4600, 4600 ifname = A, C rf2 = 5100, 5100 fe = '6cm', '6cm' pol = RCP, LCP lo1 = 4500.00, 4500.00 ! updated may 1999 with information from KM Shibata / Name = ka1cm Station = KASHIM34 priority = 5 rf1 = 21800, 21800 ifname = A, C rf2 = 23800, 23800 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 16800.00, 16800.00 ! updated may 1999 with information from KM Shibata / Name = no1cm Station = NOBEYAMA priority = 5 rf1 = 22000, 22000 ifname = A, C rf2 = 22300, 22300 fe = '1cm', '1cm' pol = RCP, LCP lo1 = 21000.00, 21000.00 ! fake values pge 2-feb-99 / ! The following are VERA stations forwarded from Cormac Reynolds from ! Simon Ellingsen from Mareki Honma. See Reynolds email of Jan. 3, 2010. ! The stations are Mizusawa and Yamaguchi. They could be merged into a ! single entry, but I'll keep as is for now. RCW March 22, 2010. Name = Vm5cm Station = VERAMZSW priority = 4 rf1 = 6600, 6600 ifname = C, A rf2 = 6700, 6700 fe = '5cm', '5cm' pol = LCP lo1 = 6403, 6403 note = 'RF-256 MHz' ! M Honma (04/Feb/2009) / Name = Ym5cm Station = YAMAGU32 priority = 4 rf1 = 6600, 6600 ifname = C, A rf2 = 6700, 6700 fe = '5cm', '5cm' pol = LCP lo1 = 6403, 6403 note = 'RF-256 MHz' ! K Fujisawa (05/Feb/2009) / ! ===================================================================== ! The following entries in the SCHED frequency catalog are for the ! DSN antennas. ! These stations are maintained in file freq_DSN.dat. ! ===================================================================== ! ! DSN data also originally from Huib Jan van Langevelde ! Modified by Jim Ulvestad, 21 November 1997, based on information ! from Chuck Naudet of JPL. ! Removed S2 July 22, 2010 RCW. ! ! Changed to DSS names Oct 10, 2011. RCW. ! GOLD70 and GOLDMARS -> DSS14 Took out one entry like the last ! but with a RF range that seemed too wide. ! TID70 -> DSS43 ! ROB70 -> DSS63 ! Name = go18cm Station = DSS14 priority = 5 rf1 = 1608, 1608 ifname = '2N', '1N' fe = '18cm', '18cm' rf2 = 1708, 1708 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1380.0, 1380.0 note = 'LO from Altunin 3Feb97, must be Low patch (well they do anything)' ! Range assuming high patch ! rf and LO from Chuck Naudet, 20 Nov. 1997 (jsu) / Name = go13cm Station = DSS14 priority = 5 rf1 = 2265, 2265 ifname = '2N', '1N' fe = '13cm', '13cm' rf2 = 2305, 2305 altifn = '1A', '2A' pol = RCP, LCP lo1 = 2000.0, 2000.0 note = 'LO from Altunin 3Feb97, must be Low patch (well they do anything)' ! Range assuming high patch ! rf and LO from Chuck Naudet, 20 Nov. 1997 (jsu) / Name = go4cm Station = DSS14 priority = 5 rf1 = 8400, 8400 ifname = '2N', '1N' fe = '4cm', '4cm' rf2 = 8500, 8500 altifn = '1A', '2A' pol = RCP, LCP lo1 = 8100.00,8100.00 note = 'LO from Altunin via LJG via Greenhill' ! confirmed by Chuck Naudet, 20 Nov. 1997 (jsu) / Name = go1cm Station = DSS14 priority = 5 rf1 = 22140,22140 ifname = '2N', '1N' fe = '1cm', '1cm' rf2 = 22410,22410 altifn = '1A', '2A' pol = RCP, LCP lo1 = 21914.0,21914.0 note = 'LO from Altunin 01Nov96, must be High patch (well they can do anything)' ! Range assuming low patch, but there is a problem with filters / Name = ti18cm Station = DSS43, DSS45, DSS43LBA, DSS45LBA, DSS34, DSS34LBA priority = 5 rf1 = 1608, 1608 ifname = '2N', '1N' fe = '18cm', '18cm' rf2 = 1708, 1708 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1380.00, 1380.00 note = 'LO from Harbison, e-mail 20/03/97. other values guesses' ! especially no idea on rf* and if names, uses ?? DAR ! earlier email suggested 1480 firstlo. ! rf and lo from Naudet, 20 Nov 1997 (jsu) / Name = ti13cm Station = DSS43, DSS45, DSS43LBA, DSS45LBA, DSS34, DSS34LBA priority = 5 rf1 = 2265, 2265 ifname = '2N', '1N' fe = '13cm', '13cm' rf2 = 2305, 2305 altifn = '1A', '2A' pol = RCP, LCP lo1 = 2000.00, 2000.00 note = 'LO from Harbison, e-mail 20/03/97. other values guesses' ! Email forwarded by Bill Scott. ! especially no idea on rf* and if names, uses ?? DAR ! IF range based on high patch nominal values. ! rf and LO confirmed by Chuck Naudet, 20 Nov. 1997 (jsu) / Name = ti4cm Station = DSS43, DSS34, DSS45, DSS43LBA, DSS45LBA, DSS34, DSS34LBA priority = 5 rf1 = 8200, 8200 ifname = '2N', '1N' fe = '4cm', '4cm' rf2 = 8600, 8600 altifn = '1A', '2A' pol = RCP, LCP lo1 = 8100.00, 8100.00 note = 'LO from Harbison, e-mail 20/03/97. other values guesses' ! Email forwarded by Bill Scott. ! especially no idea on rf* and if names, uses ?? DAR ! IF range based on high patch nominal values. ! rf and LO confirmed by Chuck Naudet, 20 Nov. 1997 (jsu) ! June 2009 from Shingi Horiuchi rf range 8200-8600. Was 8400-8500 ! Need to confirm LO. / Name = tisx Station = DSS43, DSS34, DSS45, DSS43LBA, DSS45LBA priority = 5 rf1 = 2200, 8200 ifname = '2N', '1N' fe = '13cm', '4cm' rf2 = 2600, 8600 altifn = '1A', '2A' pol = RCP, RCP lo1 = 2100.00, 8100.00 note = 'LO from Harbison, e-mail 20/03/97. other values guesses' / Name = ti1cm Station = DSS43, DSS45, DSS43LBA, DSS45LBA, DSS34, DSS34LBA priority = 5 rf1 = 18000, 18000 ifname = '2N', '1N' fe = '1cm', '1cm' rf2 = 26000, 26000 altifn = '1A', '2A' pol = RCP, LCP lo1 = 21914.00, 21914.00 note = 'LO from Harbison, e-mail 03/02/97 other values guesses' ! especially no idea on rf* and if names, uses ?? DAR / Name = ti7mm Station = DSS34, DSS34LBA priority = 5 rf1 = 31910, 31910 ifname = '2N', '1N' fe = '7mm', '7mm' rf2 = 32190, 32190 altifn = '1A', '2A' pol = RCP, LCP lo1 = 31000.00, 31000.00 note = 'LO fake' / Name = ro18cm Station = DSS63 priority = 5 rf1 = 1608, 1608 ifname = '2N', '1N' fe = '18cm', '18cm' rf2 = 1708, 1708 altifn = '1A', '2A' pol = RCP, LCP lo1 = 1380.00, 1380.00 note = 'LO from Harbison, e-mail 20/03/97. other values guesses' ! especially no idea on rf* and if names, uses ?? DAR ! earlier email suggested 1480 firstlo. ! rf and LO confirmed by Chuck Naudet, 20 Nov. 1997 (jsu) / Name = ro13cm Station = DSS63 priority = 5 rf1 = 2265, 2265 ifname = '2N', '1N' fe = '13cm', '13cm' rf2 = 2305, 2305 altifn = '1A', '2A' pol = RCP, LCP lo1 = 2000.00, 2000.00 note = 'LO from Harbison, e-mail 20/03/97. other values guesses' ! Email forwarded by Bill Scott. ! especially no idea on rf* and if names, uses ?? DAR ! IF range based on high patch nominal values. ! rf and LO confirmed by Chuck Naudet, 20 Nov. 1997 (jsu) / Name = ro4cm Station = DSS63 priority = 5 rf1 = 8400, 8400 ifname = '2N', '1N' fe = '4cm', '4cm' rf2 = 8500, 8500 altifn = '1A', '2A' pol = RCP, LCP lo1 = 8100.00, 8100.00 note = 'LO from Harbison, e-mail 20/03/97. other values guesses' ! Email forwarded by Bill Scott. ! especially no idea on rf* and if names, uses ?? DAR ! IF range based on high patch nominal values. ! rf and LO confirmed by Chuck Naudet, 20 Nov. 1997 (jsu) / Name = ro1cm Station = DSS63 priority = 5 rf1 = 18000, 18000 ifname = '2N', '1N' fe = '1cm', '1cm' rf2 = 26000, 26000 altifn = '1A', '2A' pol = RCP, LCP lo1 = 21914.00, 21914.00 note = 'LO from Harbison, e-mail 03/02/97 other values guesses' ! especially no idea on rf* and if names, uses ?? DAR / ! ! ===================================================================== ! The following entries in the SCHED frequency catalog are for mm ! VLBI stations only. ! These stations are maintained in file freq_mm.dat. ! ===================================================================== ! Initial entries from mm-stations.dat from Krichbaum, Sept. 26, 2005. ! Actually none of these stations are in common use now (2005). ! Haystack at 3 mm dual-pol ! ! Receiver B is LCP, A is RCP Name = 3mm_haystk Station = HAYSTACK Priority = 0 rf1 = 86140, 86140 ifname = '1N', '2N' altifn = '1A', '2A' rf2 = 86540, 86540 fe = '3mm', '3mm' pol = RCP, LCP lo1 = 86040, 86040 note = '3-mm CMVA' / ! Haystack at 3 mm single-pol ! Name = 3mm_haystk-lcp Station = HAYSTACK Priority = 0 rf1 = 86140, 86140 ifname = '1N', '2N' altifn = '1A', '2A' rf2 = 86540, 86540 fe = '3mm', '3mm' pol = LCP, LCP lo1 = 86040, 86040 !this works with 86210.99 note = '3-mm CMVA LCP only' / ! Quabbin at 3 mm ! Name = 3mm_quabn Station = QUAB Priority = 0 rf1 = 86169, 86169 ifname = '1N', '2N' altifn = '1A', '2A' rf2 = 86569, 86569 fe = '3mm', '3mm' pol = RCP, LCP lo1 = 86069.1, 86069.1 note = '3-mm CMVA' / ! Kitt Peak 12-m at 3 mm ! Name = 3mm_KP12m Station = KITTPEAK Priority = 0 rf1 = 86168, 86168 ifname = B, D rf2 = 86668, 86668 fe = '3mm', '3mm' pol = RCP, LCP lo1 = 85295, 85295 note = '3-mm CMVA' / ! Name = 3mm_KP12m-l Station = KITTPEAK Priority = 0 rf1 = 86168, 86168 ifname = B, D rf2 = 86668, 86668 fe = '3mm', '3mm' pol = LCP, LCP lo1 = 85295, 85295 note = '3-mm CMVA' / ! KITTPEAK v=2 SiO ! Name = 3mm_v2SiO_12m Station = KITTPEAK Priority = 0 rf1 = 85500, 85500 ifname = B, D rf2 = 86000, 86000 fe = '3mm', '3mm' pol = RCP, LCP lo1 = 84686, 84686 / ! KITTPEAK 29 SiO ! Name = 3mm_29SiO_12m Station = KITTPEAK Priority = 0 rf1 = 85500, 85500 ifname = B, D rf2 = 86000, 86000 fe = '3mm', '3mm' pol = RCP, LCP lo1 = 84808, 84808 / ! 2mm VLBI test KITTPEAK 12m - PICOVEL ! Pico Veleta (IRAM) at 2 mm ! Name = 2mm_pico-l Station = PICOVEL Priority = 0 rf1 = 128000,128000 ifname = B, D rf2 = 130000,130000 fe = '2mm', '2mm' pol = LCP, LCP lo1 = 128670,128670 note = '2-mm test' / ! Kitt Peak 12m at 2 mm ! Name = 2mm_KP12m-l Station = KITTPEAK Priority = 0 rf1 = 128000,128000 ifname = B, D rf2 = 130000,130000 fe = '2mm', '2mm' pol = LCP, LCP lo1 = 128670,128670 note = '2-mm test' / ! ! ===================================================================== ! The following entries in the SCHED frequency catalog are for geodetic ! VLBI stations only. It's a bit thin so far! ! These stations are maintained in file freq_geodesy.dat. ! ===================================================================== Name = ap_sx Station = ALGOPARK priority = 5 rf1 = 2040, 2040, 8100, 8100 ifname = B, D, A, C rf2 = 2540, 2540, 8600, 8600 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, LCP lo1 = 1540.1, 1540.1, 7600.1, 7600.1 note = 'Based on Norbert Bartel info 20 Jan 2003.' ! ranges from assuming BBC can do 500 - 1000 MHz / Name = ap_sxw Station = ALGOPARK priority = 5 rf1 = 2040, 2040, 8100, 8580 ifname = B, D, A, C rf2 = 2540, 2540, 8600, 9080 fe = '13cm', '13cm', '4cm', '4cm' pol = RCP, LCP, RCP, RCP lo1 = 1540.1, 1540.1, 7600.1, 8080.0 note = 'Based on Norbert Bartel info 20 Jan 2003.' ! ranges from assuming BBC can do 500 - 1000 MHz / Name = ap_x Station = ALGOPARK priority = 4 rf1 = 8100, 8100 ifname = C, A rf2 = 8600, 8600 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7600.1, 7600.1 note = 'Based on Norbert Bartel info 20 Jan 2003.' ! ranges from assuming BBC can do 500 - 1000 MHz / Name = ap_x Station = ALGOPARK priority = 4 rf1 = 8100, 8580 ifname = A, C rf2 = 8600, 9080 fe = '4cm', '4cm' pol = RCP, LCP lo1 = 7600.1, 8080.0 note = 'Based on Norbert Bartel info 20 Jan 2003.' ! ranges from assuming BBC can do 500 - 1000 MHz / ! From Haystack via Walter Brisken just before the real time test ! of May 7, 2007 ! Name = westx ! Station = WESTFORD Priority = 0 ! rf1 = 8180, 8180 ifname = '1N', '2N' altifn = '1A', '2A' ! rf2 = 8580, 8580 fe = '2cm', '2cm' ! pol = RCP, LCP lo1 = 8080, 8080 ! note = 'Westford - xband'/ Name = westx Station = WESTFORD Priority = 0 rf1 = 8180 ifname = '1N' altifn = '1A' rf2 = 8580 fe = '4cm' pol = RCP lo1 = 8080 note = 'Westford - xband'/ ! The LO's are 2020 and 8080 MHz with the IF upconverted by 479.9 MHz ! for the VLBA BBCs (need 500-1000 MHz). RCP only. ! Trying to feed all BBC's with X band will be a special patch case ! requiring a special setup. Name = tg_sx Station = TIGOCONC,OHIGGINS priority = 5 rf1 = 2210, 8180, 8580 ifname = B, A, C rf2 = 2450, 8600, 8980 fe = '13cm', '4cm', '4cm' pol = RCP, RCP, RCP lo1 = 1540.1, 7600.1, 8080.0 note = 'Based on email from Roopesh Ojha Nov. 10, 2008' /