Welcome to program SCHED. Version: 11.30 Version 11.3 update 1. April 14, 2014 The manual is at http://www.aoc.nrao.edu/software/sched/index.html Unix users should set $SCHED to the base area where SCHED is installed. Most run time messages will be in sched.runlog Some useful commands to give now if running interactively: SCHedule= : Specify input file. PLOT : Invokes uv, xy, rd, and uptime plotting. FREQLIST=lowF,highF : Make frequency list (MHz). Then exit. EXIT : Leave program. / : End of inputs - run program (or EXIT). RDSET: Reading setup file: sess314.X512 STREAD: Reading station catalog: ./sta.sess314nme.dat STREAD: Reading locations file: ./loc.sess314nme.dat SRREAD: Reading source catalog: /usr/local/sched_11.3U1/catalogs/sources.vlba GETFREQ: Reading frequency file: /usr/local/sched_11.3U1/catalogs/freq.dat INPUT: Found 31 input scans. SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETCHAN: Must use dual sidebands because of the maximum BBCs available at some site: 8 SETFCAT: In setup: sess314.X512 Station ONSALA60 WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band onsx 1 2 F T T T T T T T onsx 2 2 F T F T T T T T onsx 3 2 F T T T T T T T onsx 4 2 F T F T T T T T onsx 5 2 F T T T T T T T onsx 6 2 F T F T T T T T onsx 7 2 F T T T T T T T onsx 8 2 F T F T T T T T onsx 9 2 F T T T T T T T onsx 10 2 F T F T T T T T onsx 11 2 F T T T T T T T onsx 12 2 F T F T T T T T onsx 13 2 F T T T T T T T onsx 14 2 F T F T T T T T onsx 15 2 F T T T T T T T onsx 16 2 F T F T T T T T onxd 1 2 F T T T T T T T onxd 2 1 F T T T T T T T onxd 3 2 F T T T T T T T onxd 4 1 F T T T T T T T onxd 5 2 F T T T T T T T onxd 6 1 F T T T T T T T onxd 7 2 F T T T T T T T onxd 8 1 F T T T T T T T onxd 9 2 F T T T T T T T onxd 10 1 F T T T T T T T onxd 11 2 F T T T T T T T onxd 12 1 F T T T T T T T onxd 13 2 F T T T T T T T onxd 14 1 F T T T T T T T onxd 15 2 F T T T T T T T onxd 16 1 F T T T T T T T --------------------------------------- SETFCAT: In setup: sess314.X512 Station NOTO WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band ntsx 1 3 F F T T T T T T ntsx 2 3 F F F T T T T T ntsx 3 3 F F T T T T T T ntsx 4 3 F F F T T T T T ntsx 5 3 F F T T T T T T ntsx 6 3 F F F T T T T T ntsx 7 3 F F T T T T T T ntsx 8 3 F F F T T T T T ntsx 9 3 F F T T T T T T ntsx 10 3 F F F T T T T T ntsx 11 3 F F T T T T T T ntsx 12 3 F F F T T T T T ntsx 13 3 F F T T T T T T ntsx 14 3 F F F T T T T T ntsx 15 3 F F T T T T T T ntsx 16 3 F F F T T T T T nt_xd 1 1 F F T T T T T T nt_xd 2 2 F F T T T T T T nt_xd 3 1 F F T T T T T T nt_xd 4 2 F F T T T T T T nt_xd 5 1 F F T T T T T T nt_xd 6 2 F F T T T T T T nt_xd 7 1 F F T T T T T T nt_xd 8 2 F F T T T T T T nt_xd 9 1 F F T T T T T T nt_xd 10 2 F F T T T T T T nt_xd 11 1 F F T T T T T T nt_xd 12 2 F F T T T T T T nt_xd 13 1 F F T T T T T T nt_xd 14 2 F F T T T T T T nt_xd 15 1 F F T T T T T T nt_xd 16 2 F F T T T T T T --------------------------------------- SETFCAT: In setup: sess314.X512 Station YEBES40M WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band ys40_sx 1 2 F T T T T T T T ys40_sx 2 2 F T F T T T T T ys40_sx 3 2 F T T T T T T T ys40_sx 4 2 F T F T T T T T ys40_sx 5 2 F T T T T T T T ys40_sx 6 2 F T F T T T T T ys40_sx 7 2 F T T T T T T T ys40_sx 8 2 F T F T T T T T ys40_sx 9 2 F T T T T T T T ys40_sx 10 2 F T F T T T T T ys40_sx 11 2 F T T T T T T T ys40_sx 12 2 F T F T T T T T ys40_sx 13 2 F T T T T T T T ys40_sx 14 2 F T F T T T T T ys40_sx 15 2 F T T T T T T T ys40_sx 16 2 F T F T T T T T ys40_4cm 1 2 F T T T T T T T ys40_4cm 2 1 F T T T T T T T ys40_4cm 3 2 F T T T T T T T ys40_4cm 4 1 F T T T T T T T ys40_4cm 5 2 F T T T T T T T ys40_4cm 6 1 F T T T T T T T ys40_4cm 7 2 F T T T T T T T ys40_4cm 8 1 F T T T T T T T ys40_4cm 9 2 F T T T T T T T ys40_4cm 10 1 F T T T T T T T ys40_4cm 11 2 F T T T T T T T ys40_4cm 12 1 F T T T T T T T ys40_4cm 13 2 F T T T T T T T ys40_4cm 14 1 F T T T T T T T ys40_4cm 15 2 F T T T T T T T ys40_4cm 16 1 F T T T T T T T --------------------------------------- SETFCAT: In setup: sess314.X512 Station TIANMA65 WRTMSG: Special message from routine SETFCAT: ----------- WARNING ----------- SCHED could not find a frequency catalog group that matched the setup file and station mentioned above. Below are the closest matches with at least some overlap in RF frequency. You can use FREQLIST (a main program input) to get the frequency catalog group and IF numbers that are available. Or you can look in freq.dat in the catalogs area. Since SCHED cannot confirm the validity of your setup, check and be very sure it is correct! In the table below, a match is indicated by a T. A mismatch is indicated by F. FreqCat Baseband FreqCat IF First Pol RF VLA FE RF RF Group Channel IF Name LO Chan 1 IF Freq Band --------------------------------------- SCHOPT: First output scan will be number 1 WRTMSG: Special message from routine AUTODOWN: * Stations using automatic tape allocation or disk recording systems are being removed from scans when the source is below the antenna pointing limits. This behavior can be overridden using DODOWN. SCHOPT: There will be 31 output scans ( 1 - 31) from 308/10:30:00 to 308/13:30:00 SUMOPE: Writing summary file n14x1.sum STALST: WARNING - A station has zero axis offset, which is unlikely. Accurate positions, including axis offsets are needed for correlation. Is your station location information adequate? See the summary file station list to see which stations are suspect. OMSOUT: Writing OMS file n14x1.oms VXWRT : Writing V E X file n14x1.vex VXWRIF: WARNING, Phase cal not under computer control for some stations. Contact stations by e-mail to make sure phase cal is switched off Phase cal is under computer control for VLBA stations and many others. V2DOUT: Writing V2D file n14x1.tv2d FLAGS: Writing apriori flagging file n14x1.flag Processing EFLSBERG Processing WSTRBORK Processing ONSALA60 Processing NOTO Processing SVETLOE Processing ZELENCHK Processing BADARY Processing SHANGHAI Processing HART Processing YEBES40M Processing TIANMA65